Rubber & FoamSKU IP-SILP-16X12.3X5-BLACK-10
Silicone L Profile – 16mm x 12.3mm, 5mm Legs, Soft 30 Shore A – 10m or 25m Coil
Price shown updates with the option you pick.
A heavy-wall, very soft silicone angle profile: 16mm across the base, 12.3mm high and a solid 5mm thick on both legs. At 30 Shore A it squashes easily, so it cushions knocks and seals against uneven edges far better than a firm trim. Sold as a continuous 10m or 25m coil in seven colours, held in stock in the UK.
At a glance
- Size: 16mm wide x 12.3mm high, 5mm leg thickness (11mm x 7.3mm inside faces)
- Material: solid silicone rubber, 30 Shore A, 910% elongation at break
- Temperature: stays flexible from -50°C to +180°C
- Compound compliance (supplier datasheet text): FDA 21 CFR 177.2600, EC 1935/2004, WRAS approved
- Coils: 10m (£75.00/m) or 25m (£39.60/m), inc VAT
- Colours: black, blue, green, red, translucent, white, yellow
Technical drawing
![]()
Orange dimensions are the supplier's; the grey inside sizes (11mm and 7.3mm) are derived from them. Corners are square.
Specification
| Property | Value | Test method |
|---|---|---|
| Profile | Solid L (angle) section, unequal legs, square corners | - |
| Overall width (base leg) | 16 mm | Supplier drawing |
| Overall height (upright leg) | 12.3 mm | Supplier drawing |
| Base leg thickness | 5 mm | Supplier drawing |
| Upright leg thickness | 5 mm | Supplier drawing |
| Inside face, base (derived) | 11 mm (16 - 5) | Calculated |
| Inside face, upright (derived) | 7.3 mm (12.3 - 5) | Calculated |
| Cross-section area (derived) | approx. 116.5 mm² | Calculated |
| Weight (derived) | approx. 128 g/m; 1.3 kg per 10m, 3.2 kg per 25m | Calculated from area x density |
| Material | Silicone rubber | - |
| Hardness | 30 Shore A | DIN ISO 48-4 |
| Density | 1.10 g/cm³ | DIN EN ISO 1183-1 A |
| Tensile strength | 10 N/mm² (10 MPa) | ISO 37 Type 1 |
| Elongation at break | 910 % | ISO 37 Type 1 |
| Tear strength | 28 N/mm | ASTM D 624 B |
| Compression set (22 h at 175°C) | 20 % | DIN ISO 815-1 Type B, Method A |
| Rebound resilience | 58 % | ISO 4662 |
| Working temperature | -50°C to +180°C | - |
| Environmental resistance | Ozone, UV, oxidation, weathering, cosmic and ionising radiation, corona discharge | - |
| Dimensional tolerance | ISO 3302-1:2014 Class E2 | ISO 3302-1 |
| Colours | Black, blue, green, red, translucent, white, yellow | - |
| Supplied as | Continuous coil, 10m or 25m | - |
Materials and compliance
The silicone compound used for this profile is stated in the manufacturer's datasheet to comply with:
- FDA 21 CFR 177.2600 (rubber articles for repeated food contact)
- EC 1935/2004 (materials in contact with food)
- WRAS approved material (potable water)
- Free from TSE/BSE-derived products and free from phthalates
These are material statements for the compound. Check that the approval covers your exact application, contact temperature and food type before use.
How it fits
![]()
The inside of the L sits over a square outside corner. It covers 11mm of one face and 7.3mm of the other, with 5mm of soft silicone standing proud on both. Fit the 16mm leg to whichever face takes the knocks or needs the wider seal.
Typical uses
- Soft corner guard on benches, cabinets, machine guards and panel edges
- Angle seal around enclosure doors, hatches, ovens and HVAC panels where heat rules out PVC or EPDM
- Colour-coded edging in food, drink and pharmaceutical areas
- Cushioned edge on glass, sheet metal and acrylic during handling or in service
- Edge finish in cleanrooms and laboratories, where silicone wipes clean and stays flexible
Fitting tips
- Degrease both faces of the corner with isopropyl alcohol and let them dry.
- For a loose cushion it can be pressed on dry. For a permanent or watertight fit, run a bead of silicone or polyurethane adhesive sealant along both inside faces.
- Lay it on without stretching. Very soft silicone stretched during fitting will creep back and leave gaps at the ends.
- Cut square with a sharp knife in one stroke. Mitre corners at 45° and seal the joint with silicone.
How much do I need?
Add up every edge you want to cover and allow about 5% for trimming and mitres. Example: four bench fronts 1.8m long need 4 x 1.8 = 7.2m, plus 5% = 7.6m, so one 10m coil. Twelve 1.8m edges (22.7m with allowance) fit on one 25m coil, which works out at about half the price per metre.
Related profiles
- Silicone L Profile 15mm x 12mm, 5mm thick: almost the same size, 25m coil
- Silicone L Profile 16mm x 10mm: same base width with a lower upright
- Silicone L Profile 17mm x 14mm, 40 Shore A: slightly larger and a little firmer
- Silicone L Profile 20mm x 10mm: wider base for more bonding area
FAQ
How do I fit it?
Clean the corner, then either press it on dry for a light-duty cushion or bond it with a silicone or polyurethane adhesive sealant on both inside faces for a permanent, watertight fit. No tools beyond a sharp knife are needed.
Will it fit my edge? How do I size it?
It fits over a square outside corner. The inside faces are 11mm and 7.3mm long, so measure how much of each face you want covered. It does not clip onto a thin panel edge: for that you need a U channel or edge trim.
How soft is 30 Shore A?
Very soft, softer than a typical pencil eraser. It compresses readily to seal against uneven surfaces and absorbs knocks well. If you need a firmer edge that holds its shape, choose a 60 Shore A profile.
What temperatures can it take?
The datasheet gives -50°C to +180°C working temperature, with a compression set of 20% after 22 hours at 175°C, so it keeps sealing after long periods of heat.
Can it be used in food areas or with drinking water?
The compound is stated to meet FDA 21 CFR 177.2600 and EC 1935/2004 and is a WRAS approved material. The seven colours also help with colour-coded hygiene zones.
How do I cut and join it?
Cut with a sharp knife or blade in one clean stroke. Mitre corners at 45° and bond the faces with silicone sealant or a silicone-compatible adhesive. Silicone cannot be joined with ordinary rubber cements.
Is it suitable outdoors?
Yes. Silicone resists UV, ozone and weathering and stays flexible in frost, so it will not crack or harden outside.
10m or 25m?
10m suits a few edges or a repair. 25m costs £39.60/m against £75.00/m, so it is better value for any run over about 13m.
Need help choosing a size, colour or adhesive? Contact our technical team on +44 1282 277786 or sales@industrial-polymers.co.uk.
Product details
| SKU | IP-SILP-16X12.3X5-BLACK-10 |
|---|---|
| Weight | 3.09 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Silicone L Profile – 16mm x 12.3mm, 5mm Legs, Soft 30 Shore A – 10m or 25m Coil