Rubber & FoamSKU IP-SILP-12X8.4-BLACK
Silicone L Profile – 12mm x 8.4mm, 1.5mm Wall, 70 Shore A – 25m Coil
A slim, thin-wall silicone angle: 12mm across the base and 8.4mm high, with both legs just 1.5mm thick and a 1.5mm radius in the inside corner. It sits over the outside corner of a panel, worktop, cabinet or guard to cushion a sharp edge and give it a neat, coloured finish. The firm 70 Shore A silicone stays flexible from -50°C to +180°C. Sold as a 25m continuous coil in seven colours, held in UK stock.
At a glance
- Size: 12mm wide x 8.4mm high, thin-wall angle (not a solid block)
- Walls: 1.5mm on both legs, R1.5mm inside corner
- Covers: about 10.5mm of the top face and 6.9mm of the side face of a corner
- Material: firm 70 Shore A silicone rubber, 1.18 g/cm³
- Temperature: -50°C to +180°C working range
- Compliance stated by the manufacturer: FDA 21 CFR 177.2600, EC 1935/2004, WRAS approved, free from TSE/BSE-derived products and phthalates
- Colours: black, blue, green, red, translucent, white and yellow, all at the same price
- Supplied as: 25m coil (£27.00 per metre), cut to length yourself
Technical drawing
![]()
The orange dimensions are the manufacturer's. The 10.5mm inside width (12 − 1.5) and 6.9mm inside height (8.4 − 1.5) are worked out from them.
Specification
| Property | Value | Test method / note |
|---|---|---|
| Profile | L section (equal-wall angle), thin wall | Manufacturer's drawing |
| Overall width (base leg) | 12 mm | Nominal |
| Overall height (upright leg) | 8.4 mm | Nominal |
| Wall thickness, both legs | 1.5 mm | Nominal |
| Inside corner radius | R1.5 mm | Manufacturer's drawing |
| Inside width / inside height | 10.5 mm / 6.9 mm | Derived from the dimensions above |
| Dimensional tolerance | Class E2 | ISO 3302-1:2014 |
| Coil length | 25 m continuous | One coil per unit |
| Material | Silicone rubber | - |
| Hardness | 70 Shore A | DIN ISO 48-4 |
| Density | 1.18 g/cm³ | DIN EN ISO 1183-1 A |
| Tensile strength | 11.3 N/mm² (11.3 MPa) | ISO 37 Type 1 |
| Elongation at break | 530 % | ISO 37 Type 1 |
| Tear strength | 31 N/mm (31 kN/m) | ASTM D624 B |
| Compression set | 40 % after 22 h at 175°C | DIN ISO 815-1 Type B, Method A |
| Rebound resilience | 55 % | ISO 4662 |
| Working temperature | -50°C to +180°C | Manufacturer's data |
| Environmental resistance | Ozone, UV, oxidation, weathering, corona discharge, cosmic and ionising radiation | Manufacturer's data |
| Colours | Black, blue, green, red, translucent, white, yellow | - |
Materials and compliance
The manufacturer's datasheet for this exact profile states that the compound meets:
- FDA 21 CFR 177.2600 (rubber articles for repeated food contact)
- EC 1935/2004 (EU food-contact materials framework)
- WRAS approved material (for use with drinking water)
- Free from TSE/BSE-derived products
- Free from phthalates
We list only the approvals the manufacturer states in writing for this product. If you need a declaration of conformity or a certificate for an audit, ask us before ordering.
How it fits
![]()
The angle drops over an outside corner. The 12mm leg lies on the top face and the 8.4mm leg runs down the side, so the corner is wrapped by 1.5mm of silicone on both faces. It works on any thickness of panel because it covers the corner, not the whole edge. To hold the edge on both faces of a thin sheet, use a U channel instead.
Typical uses
- Cushioning sharp corners on sheet-metal enclosures, cabinets, machine guards and HVAC casings
- Low-profile corner trim on glass, acrylic and composite panels
- Corner protection on food and drink processing equipment (FDA and EC 1935/2004 compound)
- Edging in potable water equipment (WRAS approved material)
- Hot-zone corners near ovens, dryers and heat-sealing machines, up to +180°C
- Colour-coded corners in food zones, cleanrooms and laboratories
- Trim on caravans, vehicles and outdoor kit, where UV and ozone resistance matter
Which profile do I need?
| Profile | Best for |
|---|---|
| 12mm x 8.4mm, 1.5mm wall, 70 Shore A (this one) | Slim, firm corner cap with a low, neat look |
| 12.5mm x 9.4mm | Similar footprint with a thicker wall for more cushioning |
| 12mm x 10mm, thin wall, 60 Shore A | Softer and a little taller, follows curves more easily |
| 12mm x 10mm, 70 Shore A | Same firm grade with a taller 10mm leg |
| 10mm x 12mm, solid | A near-solid stepped block, used as a stop or glazing ledge rather than a corner cap |
Fitting and care
- Clean and degrease the corner. Silicone sealant bonds best to dry, oil-free metal, glass or plastic.
- For simple protection the angle can be pressed on without adhesive. For a permanent or watertight fit, run a thin bead of silicone or a compatible polyurethane sealant along one or both inside faces.
- Cut with a sharp knife against a straight edge. At corners, mitre both pieces at 45° and seal the joint with a dab of silicone.
- Lay the profile in relaxed rather than stretched, so it does not pull back at the ends.
- Clean with warm soapy water or your normal food-area cleaning routine.
Questions
How does it fit a corner?
Turn it so the inside of the L faces the corner and press it on. The 12mm leg covers about 10.5mm of one face and the 8.4mm leg covers about 6.9mm of the other. The R1.5 inside corner seats best on a corner with a small arris or radius.
Will it grip a thin sheet edge on its own?
No. An L profile covers one corner, it does not clamp. Bond it with sealant, or choose a U channel if you need the edge held on both faces.
Which way round should I fit it?
Put the 12mm leg on the face that takes the most knocks or that people see, and the shorter 8.4mm leg on the other face.
How firm is it?
70 Shore A is firm, roughly like a car tyre tread. With a 1.5mm wall it gives a thin, tough cushion rather than a soft bumper.
Can it be used in food areas?
Yes. The manufacturer states that the compound meets FDA 21 CFR 177.2600 and EC 1935/2004 for food contact. Blue and other bright colours are popular in food zones because they are easy to spot.
Is it suitable for drinking water equipment?
Yes. The material is WRAS approved.
How hot and cold can it go?
The working range is -50°C to +180°C. Compression set is 40% after 22 hours at 175°C.
Will it survive outdoors?
Yes. Silicone resists UV, ozone and weathering, so it will not crack or perish in sunlight the way many black rubbers can.
How do I cut and join it?
Cut it with a sharp knife. Mitre the ends at 45° for neat corners, or butt square-cut ends together, and seal the joint with silicone sealant.
How much do I get, and is it in stock?
Each unit is a full 25m coil, which works out at £27.00 per metre. All seven colours are held in stock and dispatched from the UK.
Need help choosing a profile, or a quote for several coils? Contact our team or call +44 1282 277786.
Product details
| SKU | IP-SILP-12X8.4-BLACK |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Silicone L Profile – 12mm x 8.4mm, 1.5mm Wall, 70 Shore A – 25m Coil