Rubber & FoamSKU IP-SUC-20.5X20.2-BLACK-10
Silicone Round U Channel – 20.5mm x 20.2mm, 13.5mm Opening – for 13.5mm Edges – 10m or 25m Coil
Price shown updates with the option you pick.
A wide-mouth silicone edge trim for thick panels. This round U channel is 20.5 mm wide and 20.2 mm tall. Its 13.5 mm opening pushes over 13.5 mm board, laminate, plate or double-skin panels and grips 17.7 mm down each face. The 2.5 mm walls and 2.5 mm base keep it light and flexible, and the radiused base corners give a soft, rounded finish along the edge. It is made from 70 Shore A silicone, which works continuously from −50 °C to +180 °C. The compound is FDA 21 CFR 177.2600 compliant, EC 1935/2004 compliant and WRAS approved, so it suits food lines, hygienic enclosures and water equipment.
Choose one of seven colours (black, blue, green, red, translucent, white or yellow) and a 10 m or 25 m coil. A 10 m coil is £750.00 inc VAT (£75.00 per metre). A 25 m coil is £990.00 inc VAT (£39.60 per metre). All colours cost the same. Held in stock in the UK.
At a glance
- Fits 13.5 mm edges: 13.5 mm channel opening with a 17.7 mm deep grip
- Light, flexible section: 2.5 mm walls and a 2.5 mm base with radiused corners
- Wide temperature range: −50 °C to +180 °C continuous
- Food and water approvals: FDA 21 CFR 177.2600, EC 1935/2004 and WRAS-approved material
- Weather-proof: resists ozone, UV, oxidation and weathering
- 7 colours, 10 m or 25 m continuous coil, cut to length on site
Technical drawing
![]()
The profile is drawn to scale. All dimensions are nominal, in mm, with tolerances to ISO 3302-1:2014 Class E2.
Specifications
| Property | Value | Test method / note |
|---|---|---|
| Profile | Round-base U channel (edge trim) | – |
| Overall width | 20.5 mm | Nominal |
| Overall height | 20.2 mm | Nominal |
| Channel opening (width at the mouth) | 13.5 mm | Nominal |
| Internal depth (grip depth) | 17.7 mm | Nominal |
| Wall thickness | 2.5 mm each side | Nominal |
| Base thickness | 2.5 mm | Calculated: 20.2 − 17.7 |
| Base corners | Radiused (rounded) outer corners | From drawing |
| Fits panel / edge thickness | 13.5 mm | Manufacturer data sheet |
| Coil length | 10 m or 25 m continuous | Choose with the Length option |
| Dimensional tolerance | ISO 3302-1:2014 Class E2 | ISO 3302-1 |
| Material | Silicone rubber (VMQ) | – |
| Hardness | 70 ° Shore A | DIN ISO 48-4 |
| Density | 1.18 g/cm³ | DIN EN ISO 1183-1 A |
| Tensile strength | 11.3 N/mm² (MPa) | ISO 37 Type 1 |
| Elongation at break | 530 % | ISO 37 Type 1 |
| Tear strength | 31 N/mm | ASTM D 624 B |
| Compression set (22 h at 175 °C) | 40 % | DIN ISO 815-1 Type B, Method A |
| Rebound resilience | 55 % | ISO 4662 |
| Operating temperature | −50 °C to +180 °C continuous | – |
| Environmental resistance | Ozone, UV, oxidation, weathering, ionising and cosmic radiation, corona discharge | – |
| Colours | Black, Blue, Green, Red, Translucent, White, Yellow | Same profile and compound in every colour |
| Approx. weight | about 160 g/m (about 1.6 kg per 10 m, 4.0 kg per 25 m) | Calculated from cross-section area and density |
Materials and compliance
The manufacturer's data sheet for this profile states that the silicone compound is:
- FDA compliant to 21 CFR 177.2600 (rubber articles for repeated food contact)
- Compliant with EC 1935/2004 (materials intended to contact food)
- WRAS approved material (drinking water)
- Free from TSE/BSE by-products
- Free from phthalates
Certificates of conformity are available on request. Ask when you order.
Typical applications
- Edging 13 mm worktops, shelves and cutting boards on food preparation and processing equipment
- Protective edging on 12–13.5 mm polycarbonate, acrylic, HDPE or laminate guards and screens
- Cushioning glass or twin-wall panels held in frames, hatches and enclosure doors
- Colour-coded edging in hygienic and food processing areas
- Anti-rattle and vibration cushioning around thick plates and clamped panels
- Trim on potable water equipment where a WRAS-approved material is required
Which size do I need?
| Profile | Fits | Best for |
|---|---|---|
| 16 x 25 mm | 6 mm edges | 6 mm glass and sheet, heavier 5 mm wall |
| 15 x 40 mm | 6 mm edges | Deep-grip trim on 6 mm panels |
| 18 x 22 mm | 12 mm panels | Square-profile trim for 12 mm board |
| 20.5 x 20.2 mm (this item) | 13.5 mm edges | Thick board, plate and double-skin panels |
Fitting the channel
![]()
- Clean the edge and remove any sharp burrs or splinters.
- Start at one end and press the channel over the edge by hand.
- Work along the edge until the panel is seated at the bottom of the 17.7 mm channel.
- Cut to length with a sharp knife, leaving it slightly long so the ends butt tightly.
- For a permanent or watertight fit, run a bead of silicone sealant in the channel first.
How much do I need?
Add up every edge you want to cover and allow about 5 % for trimming. Example: three worktops of 2.0 m x 0.6 m edged on the front and both ends need 3 x 3.2 m = 9.6 m, plus 5 % = about 10 m. One 10 m coil covers that. For more than 13 m, the 25 m coil works out cheaper.
Frequently asked questions
What thickness of panel does it fit?
It is made for 13.5 mm edges. The 13.5 mm opening grips a 13.5 mm board firmly. Slightly thinner material, such as 12 or 13 mm board, can be used if you bond it in with silicone sealant. For 6 mm glass or sheet, choose the 16 x 25 mm profile.
How much of the panel face does it cover?
The channel is 17.7 mm deep, so it covers 17.7 mm down each face. The 2.5 mm base sits over the edge itself, making 20.2 mm in total.
Will it stay on without adhesive?
Yes, on panels of the right thickness. The opening is the narrowest part of the channel, so it holds onto the panel once pushed home. Where it will be knocked often or must seal against water, add silicone sealant inside the channel.
Is it food safe?
Yes. The compound is stated as FDA 21 CFR 177.2600 and EC 1935/2004 compliant, so it suits food processing equipment and worktops. The lighter colours and the translucent option make contamination easy to spot.
What temperatures can it handle?
It works continuously from −50 °C to +180 °C, so it suits freezer doors, ovens, dryers and outdoor equipment. It stays flexible at the cold end and does not melt or go brittle at the hot end.
Can I use it outdoors?
Yes. Silicone resists UV, ozone and weathering far better than most organic rubbers, so it will not crack or perish in sunlight.
How do I cut and join it?
Cut it square with a sharp knife. It bends round gentle curves. On tight outside corners, mitre the ends at 45° or cut a small V-notch from the channel side. Butt joints can be bonded with a silicone RTV sealant or a cyanoacrylate adhesive with a silicone primer.
Is it the same in every colour?
Yes. All seven colours share the same profile, compound and approvals. Only the pigment changes.
Can I buy a cut length or a bulk quantity?
The listing is for full 10 m or 25 m coils. For cut lengths, bulk quantities or other sizes, contact sales@industrial-polymers.co.uk or call +44 1282 277786.
Product details
| SKU | IP-SUC-20.5X20.2-BLACK-10 |
|---|---|
| Weight | 3.97 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Silicone Round U Channel – 20.5mm x 20.2mm, 13.5mm Opening – for 13.5mm Edges – 10m or 25m Coil