Rubber & FoamSKU IP-SIRU-5X4-25-BLACK
Silicone Round U Channel – 5mm x 4mm for 3mm Edges – 25m Coil
A compact, firm silicone U channel 5mm wide and 4mm high with a 3mm slot, made to cap edges about 3mm thick: 3mm aluminium and stainless sheet, 3mm acrylic and polycarbonate, thin glass, laminate and fibreglass panels. The slot is 3mm deep, so the trim sits low and neat on the edge, and the 80 Shore A compound is harder than most silicone trims, so it grips well and resists being pushed or knocked off. The compound is approved for food contact and drinking water (see Material compliance). Supplied as one continuous 25m coil in seven colours, all held in stock.
At a glance
- Fits edges about 3mm thick
- 5mm wide x 4mm high, 3mm slot, 3mm slot depth, 1mm walls, 1mm base
- Silicone rubber, 80 Shore A: firm, low-profile and hard-wearing
- Continuous service from -50°C to +180°C
- FDA 21 CFR 177.2600, EC 1935/2004 and WRAS approved compound
- Resists UV, ozone and weathering, so it will not crack or harden outdoors
- Black, blue, green, red, translucent, white or yellow, all at the same price
- 25m coil, about £27.00 per metre inc VAT
Technical drawing
![]()
Typical uses
- Finishing the cut edges of 3mm acrylic and polycarbonate screens, guards and display panels
- Capping 3mm aluminium or stainless sheet on machine guards, covers and enclosures
- Cushioning glass or plastic glazing in frames, cabinet doors and inspection windows
- Edge trim on lids, hatches and covers on food processing and drinking-water equipment
- Edge protection on oven, heater and lighting panels where PVC or EPDM trims would degrade
- Colour-coding panels, trays and fixtures by line, zone or allergen
Which size do I need?
Measure the edge thickness and choose the slot that matches it most closely.
| Silicone U channel | Slot / edge thickness |
|---|---|
| Silicone Round U Channel 3mm x 5mm | 1mm |
| Silicone Round U Channel 3.2mm x 7.8mm | 1.2mm |
| Silicone Round U Channel 4.1mm x 9mm | 1.5mm |
| Silicone Round U Channel 5mm x 4mm (this one) | 3mm, 3mm deep |
| Silicone U Channel 7.1mm x 13mm | 4mm |
| Silicone U Channel 15mm x 20mm | 10mm |
Specification
| Property | Value | Test method |
|---|---|---|
| Profile and dimensions | ||
| Profile | U channel with radiused outer base corners (push-on edge trim) | – |
| Overall width | 5.0 mm | – |
| Overall height | 4.0 mm | – |
| Slot (grip) width | 3.0 mm | – |
| Slot depth | 3.0 mm | – |
| Wall thickness | 1.0 mm each side | – |
| Base thickness | 1.0 mm solid | – |
| Fits panel / edge | 3 mm nominal | – |
| Dimensional tolerance | Class E2 | ISO 3302-1:2014 |
| Weight (calculated) | approx. 13 g per metre, approx. 0.33 kg per 25 m coil | From cross-section and density |
| Material properties (typical) | ||
| Material | Silicone rubber | – |
| Hardness | 80 Shore A | DIN ISO 48-4 |
| Density | 1.20 g/cm³ | DIN EN ISO 1183-1 A |
| Tensile strength | 10 N/mm² (10 MPa) | ISO 37 Type 1 |
| Elongation at break | 440 % | ISO 37 Type 1 |
| Tear strength | 28 N/mm (28 kN/m) | ASTM D624 B |
| Compression set | 78 % after 22 h at 175 °C | DIN ISO 815-1 Type B, Method A |
| Rebound resilience | 54 % | ISO 4662 |
| Operating temperature | -50 °C to +180 °C continuous | – |
| Environmental resistance | Ozone, UV, oxidation, weathering, cosmic and ionising radiation, corona discharge | – |
| Supply | ||
| Colours | Black, blue, green, red, translucent, white, yellow | – |
| Unit of sale | One continuous 25 m coil | – |
Material compliance
The manufacturer's datasheet for this exact profile states that its silicone compound meets:
- FDA 21 CFR 177.2600: the US regulation for rubber articles in repeated contact with food
- EC 1935/2004: the EU and UK framework regulation for food-contact materials
- WRAS approved: approved for contact with drinking (potable) water in the UK
- Free from TSE/BSE by-products: no animal-derived ingredients of TSE/BSE concern
- Phthalate-free: contains no phthalate plasticisers
These approvals apply to the material. Whether a finished assembly complies depends on its design and use. Compliance documents are available on request: contact our team.
How much do I need?
Add up every edge you want to cover and allow about 5% for trimming and joints. Example: six 3mm acrylic sneeze screens, each 1000 x 600mm with trim on the top and both sides (2.2m each), need 13.2m, or about 13.9m with allowance. One 25m coil covers the job with spare.
Fitting tips
- Deburr the edge and wipe off oil and dust before fitting
- Start at one end and press the channel on with your thumb, working along the edge
- Cut slightly over length with a sharp knife and push the ends together for a tight butt joint
- Where it must be sealed, permanent or fitted to a slightly thinner edge, run a bead of silicone or polyurethane sealant into the slot first
Questions
What edge thickness will it fit?
The slot is 3mm, made for 3mm panels. Edges a little thinner (around 2.5mm) can be held with a bead of silicone sealant in the slot. For 4mm panels choose the 7.1mm x 13mm channel.
Why is it only 4mm high?
It is a low-profile trim: the 3mm deep slot covers the edge and a little of each face, giving a slim, neat finish on screens, glazing and panels where a deep, bulky trim would look out of place.
Is it suitable for food equipment?
Yes. The compound is stated to meet FDA 21 CFR 177.2600 and EC 1935/2004, so it suits guards, covers and panels on food processing, packaging and catering equipment.
Can it be used with drinking water?
Yes. The material is WRAS approved for contact with potable water.
Is it suitable for hot equipment or outdoor use?
Yes. It is rated for continuous use from -50°C to +180°C and resists UV, ozone and weathering.
How do I cut and join it?
Cut it square with a sharp craft knife or scissors. For a neat joint, butt the two ends together; for a sealed joint, bond them with a silicone adhesive.
Will it go round corners?
It follows gentle curves well. At 80 Shore A it is firmer than softer silicone trims, so on a sharp 90° corner cut a small V notch in the base or butt two lengths together.
Is it a good compression seal?
It is designed as an edge trim and glazing cushion rather than a compression gasket. Its compression set at 175°C is 78%, so for a door seal that is squeezed repeatedly, ask us about a softer silicone profile.
How accurate are the dimensions?
It is extruded to ISO 3302-1 tolerance class E2, the standard precision class for rubber extrusions, so allow a few tenths of a millimetre either way on the nominal sizes.
Is it in stock?
Yes. All seven colours are held in stock, so orders go out quickly, as shown by the dispatch message above.
Can I order a shorter length or a bulk quantity?
This listing is a full 25m coil. For cut lengths or multiple coils, ask our team for a quote.
Are all colours the same price?
Yes. Every colour is the same profile, the same compound and the same price.
Need help choosing an edge trim or seal? Call +44 1282 277786, email sales@industrial-polymers.co.uk or contact our team.
Product details
| SKU | IP-SIRU-5X4-25-BLACK |
|---|---|
| Weight | 0.77 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Silicone Round U Channel – 5mm x 4mm for 3mm Edges – 25m Coil