Rubber & FoamSKU IP-SRUC-6.1X6.3-BLACK
Silicone Round U Channel – 6.1mm x 6.3mm for 2.5mm Edges – 25m Coil
A small, neat silicone U channel with a fully oval back, 6.1mm wide and 6.3mm tall, made for edges 2.5mm thick. It is the right size for 2.5mm aluminium and steel sheet, 2.5mm polycarbonate and acrylic, and thin laminate or board, where a 2mm-slot trim is too tight and a 3mm slot is too loose. The 2.5mm slot runs 3.7mm deep, and the solid 2.6mm oval base gives a soft, rounded bead along the edge that stands only 2.6mm proud of it. The compound is approved for food contact and drinking water (see Material compliance). Supplied as one continuous 25m coil in seven colours, all held in stock.
At a glance
- Made for 2.5mm edges
- 6.1mm wide x 6.3mm high, 2.5mm slot, 3.7mm slot depth, 1.8mm walls, 2.6mm solid oval base
- Low-profile: adds only about 1.8mm to each face and 2.6mm to the edge height
- Silicone rubber, 60 Shore A: flexible, and follows curves and rounded corners
- Continuous service from -50°C to +180°C
- FDA 21 CFR 177.2600, EC 1935/2004 and WRAS approved compound
- Unaffected by UV, ozone and weather, so it will not crack or harden outdoors
- Black, blue, green, red, translucent, white or yellow, all at the same price
- 25m coil, £27.00 per metre inc VAT
Technical drawing
![]()
How it fits
![]()
Typical uses
- Edging 2.5mm aluminium and stainless guards, conveyor side plates, hopper rims and access panels on food, bakery and packaging equipment
- Finishing the edges of 2.5mm polycarbonate and acrylic machine windows, screens and display panels
- Cushioning thin panels in frames, cabinet doors and inspection hatches to stop rattles
- Edge trim on lids, covers and hatches in contact with drinking water
- Protecting edges on oven, dryer, heater and lighting panels where rubber or PVC trims would harden
- Colour-coding guards, trays and fixtures by line, zone or allergen
Which size do I need?
Measure the edge thickness and choose the slot that matches it most closely. A deeper channel covers more of the edge face and grips harder; a smaller one gives a slimmer finish.
| Silicone U channel | Slot / edge thickness |
|---|---|
| Silicone Round U Channel 5mm x 8mm | 2mm, 6.5mm deep, slim |
| Silicone Round U Channel 6.1mm x 10mm | 2.1mm, 7mm deep |
| Silicone Round U Channel 6.1mm x 6.3mm (this one) | 2.5mm, 3.7mm deep, low profile |
| Silicone Round U Channel 6.5mm x 8mm | 2.5mm, 6mm deep, deeper grip |
| Silicone Round U Channel 6mm x 14.5mm | 3mm |
| Silicone Round U Channel 7.4mm x 9.1mm | 3.4mm |
Specification
| Property | Value | Test method |
|---|---|---|
| Profile and dimensions | ||
| Profile | Oval-back U channel (push-on edge trim) | – |
| Overall width | 6.1 mm | – |
| Overall height | 6.3 mm | – |
| Slot (channel) width | 2.5 mm | – |
| Slot depth | 3.7 mm | – |
| Wall thickness | 1.8 mm each side (at widest point) | – |
| Solid base below slot | 2.6 mm (calculated: 6.3 − 3.7) | – |
| Fits panel / edge | 2.5 mm | – |
| Dimensional tolerance | Class E2 | ISO 3302-1:2014 |
| Weight (calculated) | approx. 25 g per metre, approx. 0.63 kg per 25 m coil | From cross-section and density |
| Material properties | ||
| Material | Silicone rubber | – |
| Hardness | 60 Shore A | DIN ISO 48-4 |
| Density | 1.15 g/cm³ | DIN EN ISO 1183-1 A |
| Tensile strength | 11 N/mm² (11 MPa) | ISO 37 Type 1 |
| Elongation at break | 550 % | ISO 37 Type 1 |
| Tear strength | 26 N/mm (26 kN/m) | ASTM D624 B |
| Compression set | 31 % after 22 h at 175 °C | DIN ISO 815-1 Type B, Method A |
| Rebound resilience | 59 % | ISO 4662 |
| Operating temperature | -50 °C to +180 °C continuous | – |
| Environmental resistance | Ozone, UV, oxidation, weathering, cosmic and ionising radiation, corona discharge | – |
| Supply | ||
| Colours | Black, blue, green, red, translucent, white, yellow | – |
| Unit of sale | One continuous 25 m coil | – |
| Part numbers | IP-SRUC-6.1X6.3-<colour> | – |
Material compliance
The manufacturer's datasheet for this exact profile states that its silicone compound meets:
- FDA 21 CFR 177.2600: the US regulation for rubber articles in repeated contact with food
- EC 1935/2004: the EU and UK framework regulation for food-contact materials
- WRAS approved: approved for contact with drinking (potable) water in the UK
- Free from TSE/BSE by-products: no animal-derived ingredients of TSE/BSE concern
- Phthalate-free: contains no phthalate plasticisers
These approvals apply to the material. Whether a finished assembly complies depends on its design and use. Compliance documents are available on request: contact our team.
How much do I need?
Add up every edge you want to cover and allow about 5% for trimming and joints. Example: ten 2.5mm polycarbonate guard windows, each 600mm wide x 400mm high and trimmed all round (2.0m each), need 20m, or 21m with allowance. One 25m coil covers the job with spare.
Fitting tips
- Deburr the edge and wipe off oil and dust before fitting
- Start at one end and press the channel on with your thumb, working along the edge until it is fully seated
- A little soapy water on the edge helps it slide on; let it dry before use
- Cut slightly over length with a sharp knife and push the ends together for a tight butt joint
- Because the grip is a shallow 3.7mm, run a bead of silicone or polyurethane sealant into the slot on edges that are knocked often, vibrate, or must be sealed
Data sheet
Download the summary data sheet (PDF). The full specification is in the table above.
Questions
What edge thickness will it fit?
The slot is 2.5mm, so it is made for 2.5mm edges. On 2mm sheet it will be loose unless bonded; the 5mm x 8mm channel suits 2mm. For 3mm edges choose the 6mm x 14.5mm channel.
How does it compare with the 6.5mm x 8mm channel?
Both have a 2.5mm slot. This 6.1mm x 6.3mm version is lower and neater, gripping 3.7mm down each face. The 6.5mm x 8mm grips 6mm deep, so choose it where the trim must stay on without adhesive under knocks or vibration.
Is it suitable for food equipment?
Yes. The compound is stated to meet FDA 21 CFR 177.2600 and EC 1935/2004, so it suits guards, covers and panels on food processing, packaging and catering equipment.
Can it be used with drinking water?
Yes. The material is WRAS approved for contact with potable water.
Is it suitable for hot equipment or outdoor use?
Yes. It is rated for continuous use from -50°C to +180°C and resists UV, ozone and weathering.
How do I cut and join it?
Cut it square with a sharp craft knife or scissors. For a neat joint, butt the two ends together; for a sealed joint, bond them with a silicone adhesive.
Will it go round corners?
Yes, it follows curves and rounded corners well. On a sharp 90° corner, cut a small V notch out of the walls or butt two lengths together.
How accurate are the dimensions?
It is extruded to ISO 3302-1 tolerance class E2, the standard precision class for rubber extrusions, so allow a few tenths of a millimetre either way on the nominal sizes.
Is it in stock?
Yes. All seven colours are held in stock, so orders go out quickly, as shown by the dispatch message above.
Can I order a shorter length or a bulk quantity?
This listing is a full 25m coil. For cut lengths or multiple coils, ask our team for a quote.
Are all colours the same price?
Yes. Every colour is the same profile, the same compound and the same price.
Need help choosing an edge trim or seal? Call +44 1282 277786, email sales@industrial-polymers.co.uk or contact our team.
Product details
| SKU | IP-SRUC-6.1X6.3-BLACK |
|---|---|
| Weight | 1.76 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Silicone Round U Channel – 6.1mm x 6.3mm for 2.5mm Edges – 25m Coil