Rubber & FoamSKU IP-SIRU-7.4X9.1-25-BLACK
Silicone Round U Channel – 7.4mm x 9.1mm for 3.4mm Edges – 25m Coil
A sturdy silicone U channel with a rounded back, 7.4mm across and 9.1mm tall, made for edges up to 3.4mm thick. That makes it the natural fit for 3mm sheet: aluminium, stainless and mild steel, acrylic and polycarbonate, aluminium composite panel, and 3mm glass in cabinet and display doors. The 3.4mm slot runs 6.1mm deep, so it grips well down both faces, while the 2mm walls and 3mm solid round base give a soft, cushioned bumper along the exposed edge. The compound is approved for food contact and drinking water (see Material compliance). Supplied as one continuous 25m coil in seven colours, all held in stock.
At a glance
- Made for 3.4mm edges, so it suits standard 3mm sheet and 1/8in panels
- 7.4mm wide x 9.1mm high, 3.4mm slot, 6.1mm slot depth, 2mm walls, 3mm solid base with R3.8 rounded back
- Rounded back and top corners: a neat, soft edge with nothing to snag
- Silicone rubber, 60 Shore A: flexible, and follows curves and corners
- Continuous service from -50°C to +180°C
- FDA 21 CFR 177.2600, EC 1935/2004 and WRAS approved compound
- Unaffected by UV, ozone and weather, so it will not crack or harden outdoors
- Black, blue, green, red, translucent, white or yellow, all at the same price
- 25m coil, £27.00 per metre inc VAT
Technical drawing
![]()
Typical uses
- Edging 3mm polycarbonate and acrylic machine guards, sneeze screens, sight windows and display panels
- Finishing 3mm aluminium, stainless and steel access panels, hoppers and splash guards on food, packaging and catering equipment
- Cushioning 3mm glass in cabinet doors, display cases and inspection hatches
- Trimming 3mm aluminium composite panel on enclosures, signage and kiosks
- Edge trim on lids, hatches and covers that are in contact with drinking water
- Edge protection on oven, dryer, heater and lighting panels where rubber or PVC trims would harden
- Colour-coding guards, trays and fixtures by line, zone or allergen
Which size do I need?
Measure the edge thickness and choose the slot that matches it most closely. For the same slot, a deeper channel covers more of the edge face and grips harder.
| Silicone U channel | Slot / edge thickness |
|---|---|
| Silicone Round U Channel 6mm x 12mm | 2mm, 9mm deep |
| Silicone Round U Channel 6.1mm x 10mm | 2.1mm, 7mm deep |
| Silicone Round U Channel 6.5mm x 8mm | 2.5mm, 6mm deep |
| Silicone Round U Channel 5mm x 4mm | 3mm, shallow, low profile |
| Silicone Round U Channel 7.4mm x 9.1mm (this one) | 3.4mm, 6.1mm deep, 3mm round base |
| Silicone Round U Channel 6mm x 14.5mm | 3mm, deeper grip |
| Silicone U Channel 9.1mm x 14mm | 5mm |
Specification
| Property | Value | Test method |
|---|---|---|
| Profile and dimensions | ||
| Profile | Round-bottom U channel (push-on edge trim) | – |
| Overall width | 7.4 mm | – |
| Overall height | 9.1 mm | – |
| Slot (grip) width | 3.4 mm | – |
| Slot depth | 6.1 mm | – |
| Wall thickness | 2.0 mm each side | – |
| Solid base (below slot) | 3.0 mm | – |
| Base radius | R3.8 mm | – |
| Fits panel / edge | 3.4 mm | – |
| Dimensional tolerance | Class E2 | ISO 3302-1:2014 |
| Weight (calculated) | approx. 45 g per metre, approx. 1.1 kg per 25 m coil | From cross-section and density |
| Material properties (typical) | ||
| Material | Silicone rubber (VMQ) | – |
| Hardness | 60 Shore A | DIN ISO 48-4 |
| Density | 1.15 g/cm³ | DIN EN ISO 1183-1 A |
| Tensile strength | 11 N/mm² (11 MPa) | ISO 37 Type 1 |
| Elongation at break | 550 % | ISO 37 Type 1 |
| Tear strength | 26 N/mm (26 kN/m) | ASTM D624 B |
| Compression set | 31 % after 22 h at 175 °C | DIN ISO 815-1 Type B, Method A |
| Rebound resilience | 59 % | ISO 4662 |
| Operating temperature | -50 °C to +180 °C continuous | – |
| Environmental resistance | Ozone, UV, oxidation, weathering, cosmic and ionising radiation, corona discharge | – |
| Supply | ||
| Colours | Black, blue, green, red, translucent, white, yellow | – |
| Unit of sale | One continuous 25 m coil | – |
Material compliance
The manufacturer's datasheet for this exact profile states that its silicone compound meets:
- FDA 21 CFR 177.2600: the US regulation for rubber articles in repeated contact with food
- EC 1935/2004: the EU and UK framework regulation for food-contact materials
- WRAS approved: approved for contact with drinking (potable) water in the UK
- Free from TSE/BSE by-products: no animal-derived ingredients of TSE/BSE concern
- Phthalate-free: contains no phthalate plasticisers
These approvals apply to the material. Whether a finished assembly complies depends on its design and use. Compliance documents are available on request: contact our team.
How much do I need?
Add up every edge you want to cover and allow about 5% for trimming and joints. Example: six 3mm polycarbonate guards, each 1000mm wide x 700mm high with trim along the top and both sides (2.4m each), need 14.4m, or about 15.1m with allowance. One 25m coil covers the job with spare.
Fitting tips
- Deburr the edge and wipe off oil and dust before fitting
- Start at one end and press the channel on with your thumb, working along the edge until it is fully seated
- A little soapy water on the edge helps it slide on; let it dry before use
- Cut slightly over length with a sharp knife and push the ends together for a tight butt joint
- On edges thinner than 3mm, or where it must be sealed or permanent, run a bead of silicone or polyurethane sealant into the slot first
Questions
What edge thickness will it fit?
The slot is 3.4mm, so it is made for 3.4mm edges and suits standard 3mm sheet and 1/8in panels, which often measure a little over 3mm. On thinner edges add a little silicone sealant in the slot so it cannot slide off. For 2mm edges see the 6.1mm x 10mm channel, and for 5mm edges the 9.1mm x 14mm channel.
How does it compare with the 6mm x 14.5mm channel?
Both suit 3mm edges. This 7.4mm x 9.1mm version is shorter, with a 6.1mm grip and a thick rounded base, so it sits lower and gives a softer bumper. Choose the 6mm x 14.5mm when you want more of the edge face covered and a deeper grip.
Is it suitable for food equipment?
Yes. The compound is stated to meet FDA 21 CFR 177.2600 and EC 1935/2004, so it suits guards, screens and panels on food processing, packaging and catering equipment.
Can it be used with drinking water?
Yes. The material is WRAS approved for contact with potable water.
Is it suitable for hot equipment or outdoor use?
Yes. It is rated for continuous use from -50°C to +180°C and resists UV, ozone and weathering.
How do I cut and join it?
Cut it square with a sharp craft knife or scissors. For a neat joint, butt the two ends together; for a sealed joint, bond them with a silicone adhesive.
Will it go round corners?
Yes, it follows curves and rounded corners well. On a sharp 90° corner, cut a small V notch out of the walls or butt two lengths together.
How accurate are the dimensions?
It is extruded to ISO 3302-1 tolerance class E2, the standard precision class for rubber extrusions, so allow a few tenths of a millimetre either way on the nominal sizes.
Is it in stock?
Yes. All seven colours are held in stock, so orders go out quickly, as shown by the dispatch message above.
Can I order a shorter length or a bulk quantity?
This listing is a full 25m coil. For cut lengths or multiple coils, ask our team for a quote.
Are all colours the same price?
Yes. Every colour is the same profile, the same compound and the same price.
Need help choosing an edge trim or seal? Call +44 1282 277786, email sales@industrial-polymers.co.uk or contact our team.
Product details
| SKU | IP-SIRU-7.4X9.1-25-BLACK |
|---|---|
| Weight | 2.87 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Silicone Round U Channel – 7.4mm x 9.1mm for 3.4mm Edges – 25m Coil