Rubber & FoamSKU IP-SIRU-6.1X10-25-BLACK
Silicone Round U Channel – 6.1mm x 10mm for 2.1mm Edges – 25m Coil
A compact silicone U channel with a fully rounded back, 6.1mm across and 10mm tall, made for edges 2.1mm thick, which makes it the natural fit for 2mm sheet steel, stainless and aluminium, 2mm acrylic and polycarbonate, and thin glass or laminate. The 2.1mm slot runs 7mm deep, so it grips well down both faces, and the 2mm walls and 3mm solid, half-round crown give a thicker, softer bumper than slimmer 2mm trims. The compound is approved for food contact and drinking water (see Material compliance). Supplied as one continuous 25m coil in seven colours, all held in stock.
At a glance
- Made for 2.1mm edges, so it suits standard 2mm sheet
- 6.1mm wide x 10mm high, 2.1mm slot, 7mm slot depth, 2mm walls, 3mm solid full-round crown
- Thick 3mm crown: a soft, rounded bumper along the exposed edge
- Silicone rubber, 60 Shore A: flexible, and follows curves and corners
- Continuous service from -50°C to +180°C
- FDA 21 CFR 177.2600, EC 1935/2004 and WRAS approved compound
- Unaffected by UV, ozone and weather, so it will not crack or harden outdoors
- Black, blue, green, red, translucent, white or yellow, all at the same price
- 25m coil, £27.00 per metre inc VAT
Technical drawing
![]()
Typical uses
- Edging 2mm stainless and aluminium guards, access panels, hoppers and splash screens on food, packaging and catering equipment
- Finishing 2mm acrylic and polycarbonate sneeze screens, display panels and machine sight windows
- Cushioning thin glass or polycarbonate panes in cabinet doors, inspection hatches and display cases
- Edge trim on lids, hatches and covers that are in contact with drinking water
- Edge protection on oven, dryer, heater and lighting panels where rubber or PVC trims would harden
- Colour-coding guards, trays and fixtures by line, zone or allergen
Which size do I need?
Measure the edge thickness and choose the slot that matches it most closely. For the same slot, a deeper channel covers more of the edge face and grips harder.
| Silicone U channel | Slot / edge thickness |
|---|---|
| Silicone Round U Channel 3mm x 5mm | 1mm |
| Silicone Round U Channel 4.1mm x 9mm | 1.5mm |
| Silicone Round U Channel 5mm x 12.5mm | 1.6mm |
| Silicone Round U Channel 5mm x 8mm | 2mm, 6.5mm deep, slim |
| Silicone Round U Channel 6.1mm x 10mm (this one) | 2.1mm, 7mm deep, 3mm crown |
| Silicone Round U Channel 5mm x 14mm | 2mm, 12.5mm deep |
| Silicone Round U Channel 6mm x 12mm | 2mm, 9mm deep |
| Silicone Round U Channel 6mm x 14.5mm | 3mm |
Specification
| Property | Value | Test method |
|---|---|---|
| Profile and dimensions | ||
| Profile | Round-bottom U channel (push-on edge trim) | – |
| Overall width | 6.1 mm | – |
| Overall height | 10.0 mm | – |
| Slot (grip) width | 2.1 mm | – |
| Slot depth | 7.0 mm | – |
| Wall thickness | 2.0 mm each side | – |
| Crown (solid base) | 3.0 mm, full-round | – |
| Fits panel / edge | 2.1 mm | – |
| Dimensional tolerance | Class E2 | ISO 3302-1:2014 |
| Weight (calculated) | approx. 49 g per metre, approx. 1.2 kg per 25 m coil | From cross-section and density |
| Material properties (typical) | ||
| Material | Silicone rubber (VMQ) | – |
| Hardness | 60 Shore A | DIN ISO 48-4 |
| Density | 1.15 g/cm³ | DIN EN ISO 1183-1 A |
| Tensile strength | 11 N/mm² (11 MPa) | ISO 37 Type 1 |
| Elongation at break | 550 % | ISO 37 Type 1 |
| Tear strength | 26 N/mm (26 kN/m) | ASTM D624 B |
| Compression set | 31 % after 22 h at 175 °C | DIN ISO 815-1 Type B, Method A |
| Rebound resilience | 59 % | ISO 4662 |
| Operating temperature | -50 °C to +180 °C continuous | – |
| Environmental resistance | Ozone, UV, oxidation, weathering, cosmic and ionising radiation, corona discharge | – |
| Supply | ||
| Colours | Black, blue, green, red, translucent, white, yellow | – |
| Unit of sale | One continuous 25 m coil | – |
Material compliance
The manufacturer's datasheet for this exact profile states that its silicone compound meets:
- FDA 21 CFR 177.2600: the US regulation for rubber articles in repeated contact with food
- EC 1935/2004: the EU and UK framework regulation for food-contact materials
- WRAS approved: approved for contact with drinking (potable) water in the UK
- Free from TSE/BSE by-products: no animal-derived ingredients of TSE/BSE concern
- Phthalate-free: contains no phthalate plasticisers
These approvals apply to the material. Whether a finished assembly complies depends on its design and use. Compliance documents are available on request: contact our team.
How much do I need?
Add up every edge you want to cover and allow about 5% for trimming and joints. Example: eight 2mm stainless access panels, each 800mm wide x 600mm high with trim along the top and both sides (2.0m each), need 16m, or about 16.8m with allowance. One 25m coil covers the job with spare.
Fitting tips
- Deburr the edge and wipe off oil and dust before fitting
- Start at one end and press the channel on with your thumb, working along the edge until it is fully seated
- A little soapy water on the edge helps it slide on; let it dry before use
- Cut slightly over length with a sharp knife and push the ends together for a tight butt joint
- On thinner edges, or where it must be sealed or permanent, run a bead of silicone or polyurethane sealant into the slot first
Questions
What edge thickness will it fit?
The slot is 2.1mm, so it is made for 2.1mm edges and is the usual choice for standard 2mm sheet. On thinner edges add a little silicone sealant in the slot so it cannot slide off. For 1.5mm edges see the 4.1mm x 9mm channel, and for 3mm edges the 6mm x 14.5mm channel.
How does it compare with the 5mm x 8mm channel?
Both suit 2mm edges with a similar grip depth. This 6.1mm x 10mm version has thicker 2mm walls and a 3mm crown, so it gives a softer, more cushioned edge. Choose the 5mm x 8mm for a slimmer look, or the 5mm x 14mm for a much deeper grip.
Is it suitable for food equipment?
Yes. The compound is stated to meet FDA 21 CFR 177.2600 and EC 1935/2004, so it suits guards, covers and panels on food processing, packaging and catering equipment.
Can it be used with drinking water?
Yes. The material is WRAS approved for contact with potable water.
Is it suitable for hot equipment or outdoor use?
Yes. It is rated for continuous use from -50°C to +180°C and resists UV, ozone and weathering.
How do I cut and join it?
Cut it square with a sharp craft knife or scissors. For a neat joint, butt the two ends together; for a sealed joint, bond them with a silicone adhesive.
Will it go round corners?
Yes, it follows curves and rounded corners well. On a sharp 90° corner, cut a small V notch out of the walls or butt two lengths together.
How accurate are the dimensions?
It is extruded to ISO 3302-1 tolerance class E2, the standard precision class for rubber extrusions, so allow a few tenths of a millimetre either way on the nominal sizes.
Is it in stock?
Yes. All seven colours are held in stock, so orders go out quickly, as shown by the dispatch message above.
Can I order a shorter length or a bulk quantity?
This listing is a full 25m coil. For cut lengths or multiple coils, ask our team for a quote.
Are all colours the same price?
Yes. Every colour is the same profile, the same compound and the same price.
Need help choosing an edge trim or seal? Call +44 1282 277786, email sales@industrial-polymers.co.uk or contact our team.
Product details
| SKU | IP-SIRU-6.1X10-25-BLACK |
|---|---|
| Weight | 2.87 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Silicone Round U Channel – 6.1mm x 10mm for 2.1mm Edges – 25m Coil