Rubber & FoamSKU IP-SIRU-6.5X8-70-25-BLACK
Silicone Round U Channel – 6.5mm x 8mm, 2mm Slot 4mm Deep, 70 Shore A – for 2mm Edges – 25m Coil
A silicone U channel 6.5mm wide and 8mm tall with a fully rounded back and a 2mm slot, made for edges about 2mm thick: 14-gauge sheet steel, aluminium sheet, 2mm acrylic and polycarbonate, thin glass and laminate. The slot is 4mm deep, which leaves a thick 4mm solid base over the edge, and the 2.25mm walls in a firmer 70 Shore A silicone make a heavy, rounded bumper that holds a straight line and resists being knocked off. The compound is approved for food contact and drinking water (see Material compliance). Supplied as one continuous 25m coil in seven colours, all held in stock.
At a glance
- Fits edges about 2mm thick
- 6.5mm wide x 8mm high, 2.0mm slot 4mm deep, 2.25mm walls, 4.0mm solid base
- Firm 70 Shore A, thick 4mm rounded bumper
- Silicone rubber, 70 Shore A
- Continuous service from -50°C to +180°C
- FDA 21 CFR 177.2600, EC 1935/2004 and WRAS approved compound
- Unaffected by UV, ozone and weather, so it will not crack or harden outdoors
- Black, blue, green, red, translucent, white or yellow, all at the same price
- 25m coil, £27.00 per metre inc VAT
Technical drawing
![]()
Two versions of this size
This is the 70 Shore A version: a 2mm slot, 4mm deep, with 2.25mm walls, a 4mm solid base and a fully rounded back. It suits 2mm edges and gives the heavier, firmer bumper. The 60 Shore A version has the same 6.5 x 8mm outside size but a wider 2.5mm slot running 6mm deep, 2mm walls and rounded back corners. Choose it for 2.5mm edges or where you want a softer, more flexible trim that grips further down the edge.
| 60 Shore A | 70 Shore A | |
|---|---|---|
| Outside size | 6.5 x 8 mm | 6.5 x 8 mm |
| Fits edge | 2.5 mm | 2 mm |
| Slot | 2.5 mm wide, 6 mm deep | 2 mm wide, 4 mm deep |
| Wall thickness | 2.0 mm | 2.25 mm |
| Solid base | 2 mm | 4 mm |
| Back shape | Flat with rounded corners | Fully rounded, R1 top corners |
| Feel | Softer, bends round curves easily | Firmer, heavier bumper |
| Listing | View | This one |
Typical uses
- Bumper trim on 2mm stainless hatches, hoppers and chutes on food and packaging lines, where the 4mm rounded base takes knocks
- Finishing 2mm acrylic and polycarbonate screens, display panels and machine windows
- Cushioning glass or polycarbonate in cabinet doors, inspection hatches and display cases
- Edge trim on tank lids, access hatches and covers in contact with drinking water
- Edge protection on oven, heater, dryer and lighting panels where rubber or PVC trims would degrade
- Colour-coding guards, trays and fixtures by line, zone or allergen
Which size do I need?
Measure the edge thickness and choose the slot that matches it most closely. For the same slot, a deeper channel covers more of the edge face and grips harder; thicker walls give a heavier, more cushioned trim.
| Silicone U channel | Slot / edge thickness |
|---|---|
| Silicone Round U Channel 4.1mm x 9mm | 1.5mm |
| Silicone Round U Channel 5mm x 8mm | 2mm, 1.5mm walls |
| Silicone Round U Channel 6.5mm x 8mm, 70 Shore A (this one) | 2mm, 4mm deep, 2.25mm walls |
| Silicone Round U Channel 6mm x 12mm, 60 Shore A | 2mm, 9mm deep, 2mm walls |
| Silicone U Channel 4.6mm x 10mm | 2.5mm |
| Silicone Round U Channel 6.5mm x 8mm, 60 Shore A | 2.5mm, 6mm deep, 2mm walls |
| Silicone U Channel 5.6mm x 12mm | 3mm |
Specification
| Property | Value | Test method |
|---|---|---|
| Profile and dimensions | ||
| Profile | Full-round back U channel (R1.0 top corners), flat slot bottom | – |
| Overall width | 6.5 mm | – |
| Overall height | 8.0 mm | – |
| Slot (channel) width | 2.0 mm | – |
| Slot depth | 4.0 mm | – |
| Wall thickness | 2.25 mm each side | – |
| Solid base | 4.0 mm (height minus slot depth) | – |
| Corner radius | R1.0 mm at the open-end corners; back fully rounded | – |
| Fits panel / edge | 2 mm nominal | – |
| Dimensional tolerance | Class E2 | ISO 3302-1:2014 |
| Weight (calculated) | approx. 46 g per metre, approx. 1.15 kg per 25 m coil | From cross-section and density |
| Material properties (typical) | ||
| Material | Silicone rubber (VMQ) | – |
| Hardness | 70 Shore A | DIN ISO 48-4 |
| Density | 1.18 g/cm³ | DIN EN ISO 1183-1 A |
| Tensile strength | 11.3 N/mm² (11.3 MPa) | ISO 37 Type 1 |
| Elongation at break | 530 % | ISO 37 Type 1 |
| Tear strength | 31 N/mm (31 kN/m) | ASTM D624 B |
| Compression set | 40 % after 22 h at 175 °C | DIN ISO 815-1 Type B, Method A |
| Rebound resilience | 55 % | ISO 4662 |
| Operating temperature | -50 °C to +180 °C continuous | – |
| Environmental resistance | Ozone, UV, oxidation, weathering, cosmic and ionising radiation, corona discharge | – |
| Supply | ||
| Colours | Black, blue, green, red, translucent, white, yellow | – |
| Unit of sale | One continuous 25 m coil | – |
Material compliance
The manufacturer's datasheet for this exact profile states that its silicone compound meets:
- FDA 21 CFR 177.2600: the US regulation for rubber articles in repeated contact with food
- EC 1935/2004: the EU and UK framework regulation for food-contact materials
- WRAS approved: approved for contact with drinking (potable) water in the UK
- Free from TSE/BSE by-products: no animal-derived ingredients of TSE/BSE concern
- Phthalate-free: contains no phthalate plasticisers
These approvals apply to the material. Whether a finished assembly complies depends on its design and use. Compliance documents are available on request: contact our team.
How much do I need?
Add up every edge you want to cover and allow about 5% for trimming and joints. Example: six 2mm stainless hatch covers, each 1000mm wide x 700mm high with trim along the top and both sides (2.4m each), need 14.4m, or about 15.1m with allowance. One 25m coil covers the job with spare.
Fitting tips
- Deburr the edge and wipe off oil and dust before fitting
- Start at one end and press the channel on with your thumb, working along the edge until it is fully seated
- A little soapy water on the edge helps it slide on; let it dry before use
- Cut slightly over length with a sharp knife and push the ends together for a tight butt joint
- On thinner edges, or where it must be sealed or permanent, run a bead of silicone or polyurethane sealant into the slot first
Questions
What edge thickness will it fit?
The slot is 2mm. Silicone stretches a little, so edges from about 1.8mm to 2.3mm usually hold well. On thinner edges add a little silicone sealant so it cannot slide off; for 2.5mm edges the 60 Shore A 6.5 x 8mm version (2.5mm slot) is the closer fit, and for 1.5mm edges the 4.1mm x 9mm channel.
Should I choose the 60 or the 70 Shore A version?
This is the 70 Shore A version: a 2mm slot, 4mm deep, with 2.25mm walls, a 4mm solid base and a fully rounded back. It suits 2mm edges and gives the heavier, firmer bumper. The 60 Shore A version has the same 6.5 x 8mm outside size but a wider 2.5mm slot running 6mm deep, 2mm walls and rounded back corners. Choose it for 2.5mm edges or where you want a softer, more flexible trim that grips further down the edge.
Is it suitable for food equipment?
Yes. The compound is stated to meet FDA 21 CFR 177.2600 and EC 1935/2004, so it suits guards, covers and panels on food processing, packaging and catering equipment.
Can it be used with drinking water?
Yes. The material is WRAS approved for contact with potable water.
Is it suitable for hot equipment or outdoor use?
Yes. It is rated for continuous use from -50°C to +180°C and resists UV, ozone and weathering.
How do I cut and join it?
Cut it square with a sharp craft knife or scissors. For a neat joint, butt the two ends together; for a sealed joint, bond them with a silicone adhesive.
Will it go round corners?
Yes, it follows curves and rounded corners. On a sharp 90° corner, cut a small V notch out of the walls or butt two lengths together. Being firmer and thicker, this version needs a slightly larger bend radius than the 60 Shore A version.
How accurate are the dimensions?
It is extruded to ISO 3302-1 tolerance class E2, the standard precision class for rubber extrusions, so allow a few tenths of a millimetre either way on the nominal sizes.
Is it in stock?
Yes. All seven colours are held in stock, so orders go out quickly, as shown by the dispatch message above.
Can I order a shorter length or a bulk quantity?
This listing is a full 25m coil. For cut lengths or multiple coils, ask our team for a quote.
Are all colours the same price?
Yes. Every colour is the same profile, the same compound and the same price.
Need help choosing an edge trim or seal? Call +44 1282 277786, email sales@industrial-polymers.co.uk or contact our team.
Product details
| SKU | IP-SIRU-6.5X8-70-25-BLACK |
|---|---|
| Weight | 2.65 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Silicone Round U Channel – 6.5mm x 8mm, 2mm Slot 4mm Deep, 70 Shore A – for 2mm Edges – 25m Coil