Rubber & FoamSKU IP-SRUC-8X21-BLACK-10
Silicone Round U Channel – 8mm x 21mm, 3mm Slot 18.5mm Deep – for 3mm Edges – 10m or 25m Coil
Price shown updates with the option you pick.
A sturdy silicone edge trim with thick 2.5mm walls: the 8mm x 21mm round U channel slides 18.5mm down over a 3mm panel and finishes the edge with a fully rounded, 2.5mm-thick closed base. The 60 Shore A silicone stays flexible from -50°C to +180°C and shrugs off UV, ozone and washdown. Choose a 10m or 25m coil in any of seven colours.
At a glance
- 8mm wide x 21mm high, R4 fully rounded closed base
- 3mm wide slot, 18.5mm deep, with a rounded (R1.5) slot floor
- 2.5mm side walls, 2.5mm base: a heavier, more cushioned trim than thin-wall channels
- Silicone rubber, 60 Shore A, -50°C to +180°C
- Compound stated as FDA 21 CFR 177.2600, EC 1935/2004 and WRAS approved
- Black, blue, green, red, translucent, white or yellow
- In stock: 10m coil £750.00 (£75.00/m) or 25m coil £990.00 (£39.60/m), prices inc VAT
Technical drawing
![]()
Cross-section drawn to scale. Nominal dimensions in mm; tolerance ISO 3302-1:2014 Class E2.
Specification
| Property | Value | Test method / note |
|---|---|---|
| Profile | Round-base U channel (edge trim) | - |
| Overall width | 8 mm | Nominal |
| Overall height | 21 mm | Nominal |
| Slot (channel) width | 3 mm | Nominal |
| Slot depth | 18.5 mm | Nominal, from supplier drawing |
| Side wall thickness | 2.5 mm | Nominal |
| Base thickness | 2.5 mm | Calculated: 21 mm height less 18.5 mm slot |
| Base shape | Fully rounded (R4), rounded slot floor (R1.5) | From supplier drawing |
| Fits panel / edge | 3 mm | - |
| Dimensional tolerance | ISO 3302-1:2014 Class E2 | ISO 3302-1 |
| Material | Silicone rubber | - |
| Hardness | 60 Shore A | DIN ISO 48-4 |
| Density | 1.15 g/cm³ | DIN EN ISO 1183-1 A |
| Tensile strength | 11 N/mm² (MPa) | ISO 37 Type 1 |
| Elongation at break | 550 % | ISO 37 Type 1 |
| Tear strength | 26 N/mm | ASTM D 624 B |
| Compression set (22 h at 175°C) | 31 % | DIN ISO 815-1 Type B, Method A |
| Rebound resilience | 59 % | ISO 4662 |
| Working temperature | -50°C to +180°C | - |
| Environmental resistance | Ozone, UV, oxidation, weathering, ionising radiation, corona discharge | - |
| Approx. weight | About 0.12 kg per metre | Our calculation from the cross-section and density, not a measured value |
| Colours | Black, blue, green, red, translucent, white, yellow | - |
| Supplied as | 10 m or 25 m continuous coil | - |
Materials and compliance
The manufacturer's datasheet for this profile states the compound is:
- FDA 21 CFR 177.2600 compliant (rubber articles for repeated food contact)
- EC 1935/2004 compliant (food contact materials)
- WRAS approved material
- Free from TSE/BSE by-products
- Free from phthalates
Typical uses
- Protective edge on 3mm stainless steel machine guards, hoppers and chute panels
- Cushioned trim on 3mm acrylic, polycarbonate and glass screens and panes
- Seal strip on enclosure doors, hatches and inspection covers
- Anti-rattle packer between clamped 3mm panels
- Colour-coded edges for hygiene zones in food and drink plant
Which one do I need?
| Silicone round U channel 8mm x 21mm (this one) | 3mm panels where you want thick 2.5mm walls and an 18.5mm grip |
| Silicone round U channel 6mm x 14.5mm | A slimmer, lighter trim for 3mm edges (1.5mm walls, 13mm grip) |
| Silicone round U channel 7mm x 36mm | 3mm panels where you need a very long 34mm grip down each face |
| Silicone round U channel 9mm x 25mm | A larger, deeper profile |
| Silicone round U channel 15mm x 40mm, 8mm slot | Thicker panels up to about 8mm |
How much do I need?
Add up every edge you want to cover and add about 5% for trimming. Four guards with 4.5m of exposed edge each need about 19m, so one 25m coil does the job with spare. For a single door or hatch under 10m, the 10m coil is enough. For anything over 10m, one 25m coil (£990.00) costs less than two 10m coils (£1,500.00).
Fitting tips
- Deburr, clean and degrease the edge first.
- Start at one end and press the channel on by hand, working along the edge. Do not stretch it, or it will shrink back and leave gaps.
- Push it fully home so the panel edge sits against the slot floor, 18.5mm in.
- The 2.5mm walls make this a stiffer trim: on tight corners, cut small V-notches in the side walls so it follows the bend without buckling.
- For a watertight or permanent joint, run a bead of silicone or polyurethane sealant into the slot before fitting.
Data sheet
Download the technical data sheet (PDF)
Questions
What panel thickness does this fit?
It is made for 3mm panels. The 3mm slot grips a 3mm sheet firmly; much thinner sheet will be loose unless you bond it, and thicker sheet will not seat fully.
How far does it cover the panel?
The slot is 18.5mm deep, so the trim covers 18.5mm down each face of the panel, with a 2.5mm rounded base over the edge itself.
How do I measure what I need?
Measure the panel thickness with a caliper (it should be 3mm) and add up the length of all edges. Order a 10m or 25m coil to cover that length plus a little extra.
Is it suitable for food and drinking-water applications?
The datasheet states the compound meets FDA 21 CFR 177.2600 and EC 1935/2004 and is WRAS approved, so it is used on food processing equipment and potable water equipment.
What temperatures can it take?
-50°C to +180°C continuous, so it handles freezers, ovens, dryers and hot washdown.
Can it be used outdoors?
Yes. Silicone resists UV, ozone and weathering, so it suits outdoor enclosures, hatches and marine panels.
How do I cut and join it?
Cut square with a sharp knife or shears. For a sealed butt joint, bond the ends with a silicone adhesive. On corners, notch the walls rather than cutting right through.
Does the colour change the performance?
No. All seven colours are the same compound and profile; choose a colour for visibility, colour-coding or to match your equipment.
Is it in stock?
Yes. All seven colours in both coil lengths are held in stock and dispatched from the UK.
Need help choosing the right edge trim? Contact our team, call +44 1282 277786 or email sales@industrial-polymers.co.uk.
Product details
| SKU | IP-SRUC-8X21-BLACK-10 |
|---|---|
| Weight | 3.09 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Silicone Round U Channel – 8mm x 21mm, 3mm Slot 18.5mm Deep – for 3mm Edges – 10m or 25m Coil