Rubber & FoamSKU IP-SITS-3X6.5-SQ-25M-BLK
Silicone T Seal Profile – 3mm x 6.5mm – 25m Coil
A small, solid silicone T seal for slots about 2mm wide. The 2mm leg pushes into the slot and holds the seal in place; the 3mm head stays proud of the surface and closes the gap against dust, splash, draughts and heat. It comes as one unbroken 25m coil in seven colours, and in two head shapes that share the same 6.5mm overall height and 2mm leg.
At a glance
- Square head (Profile A): flat 3.0mm face, 3.5mm deep, for the widest contact area
- Tapered head (Profile B): 2.0mm flat face widening to 3.0mm, 3.2mm deep, giving an angled lead-in on one side
- Both: 2.0mm leg, 6.5mm overall, 0.5mm shoulder each side of the leg
- Solid silicone rubber, 50 Shore A, working range -50°C to +180°C
- Compound stated to meet FDA 21 CFR 177.2600 and EC 1935/2004 for food contact; WRAS approved material
- Black, white, translucent, red, green, blue or yellow: same size and same price
- Held in stock in both profiles and all colours
Square or tapered head: which one?
| Profile A: square head | Profile B: tapered head | |
|---|---|---|
| Head | 3.0mm wide × 3.5mm deep, square | 2.0mm flat top, sloping out to 3.0mm, 3.2mm deep |
| Leg | 2.0mm wide × 3.0mm long | 2.0mm wide × 3.3mm long |
| Minimum slot depth | 3.0mm | 3.3mm |
| Typically chosen for | Flat-faced lids and panels that close straight down onto the seal | Doors and hatches that swing or slide across the seal, where an angled edge helps them ride on |
Typical uses
- Lid and door seals on catering cabinets, warming units and proving ovens
- Slot seals in aluminium extrusion frames, guards and enclosures
- Inspection hatches and access panels on food and packaging machinery
- HVAC access doors and fan coil housings
- Colour-coded seals for hygiene zones (red, green, blue, yellow)
Technical drawing
![]()
Full specification
| Property | Value | Test method |
|---|---|---|
| Dimensions | ||
| Profile type | Solid T section, square head (A) or tapered head (B) | – |
| Overall height | 6.5 mm (both profiles) | – |
| Head width | 3.0 mm (both profiles) | – |
| Head depth | A: 3.5 mm · B: 3.2 mm | – |
| Flat face of head | A: 3.0 mm · B: 2.0 mm, then tapers to 3.0 mm | – |
| Leg width | 2.0 mm (both profiles) | – |
| Leg length below head | A: 3.0 mm · B: 3.3 mm | – |
| Dimensional tolerance | Class E2 | ISO 3302-1:2014 |
| Length per coil | 25 m, one continuous length | – |
| Material and physical properties | ||
| Compound | Solid silicone rubber | – |
| Hardness | 50 Shore A | DIN ISO 48-4 |
| Density | 1.15 g/cm³ | DIN EN ISO 1183-1, method A |
| Tensile strength | 12 N/mm² (12 MPa) | ISO 37, type 1 |
| Elongation at break | 640 % | ISO 37, type 1 |
| Tear strength | 27 N/mm (27 kN/m) | ASTM D624, die B |
| Compression set | 34 % after 22 h at 175 °C | DIN ISO 815-1, type B, method A |
| Rebound resilience | 58 % | ISO 4662 |
| Service conditions | ||
| Working temperature | -50 °C to +180 °C | – |
| Environmental resistance | Ozone, UV, oxidation, weathering, corona discharge, cosmic and ionising radiation | – |
| Supply | ||
| Colours | Black, white, translucent, red, green, blue, yellow | – |
| Unit of sale | 1 coil of 25 m (£27.00 per metre inc VAT) | – |
Materials and compliance
These are the claims the manufacturer makes in writing for this exact profile and compound. Ask us for the certificate or declaration your file needs.
| Claim | What it means for you |
|---|---|
| FDA 21 CFR 177.2600 | The compound meets the US rule for rubber articles in repeated contact with food. |
| EC 1935/2004 | The compound meets the EU framework regulation for materials that come into contact with food. |
| WRAS approved material | The material is accepted for contact with drinking water in UK water fittings. |
| Free from TSE/BSE by-products | No animal-derived ingredients that carry TSE/BSE risk. |
| Phthalate free | Made without phthalate plasticisers. |
Approvals cover the material as supplied. Whether your finished assembly complies also depends on its design, cleaning regime and the other materials in it, so check against your own requirements.
Will it fit my slot?
Measure the slot width and depth. The leg is 2.0mm wide, so it grips best in a slot of about 1.8–2.0mm. The slot needs to be at least 3.0mm deep for the square head or 3.3mm for the tapered head, so that the head sits down flat on the surface. In a slot that is slightly wide, run a thin bead of silicone adhesive along the bottom first so the leg cannot work loose.
How much do I need?
Add up the length of every slot and allow about 5% for trimming and joints. Example: a cabinet door with a 400mm × 300mm seal track needs 1.4m, or about 1.5m with allowance, so one 25m coil seals 16 doors.
Fitting tips
- Clear old seal, grease and grit out of the slot and let it dry
- Start partway along a straight side, not at a corner
- Press the leg in with your thumb or a small plastic roller as you go
- Lay the seal into corners rather than pulling it round: stretched silicone shrinks back and opens a gap
- Cut slightly long with a sharp knife and push the ends together; a dab of silicone adhesive keeps the joint closed
- For the tapered head, face the sloping side towards the edge that closes onto it
FAQ: frequently asked questions
What is the difference between the two profiles?
Only the head. Profile A has a square 3.0 × 3.5mm head with a flat top. Profile B has a 2.0mm flat top that slopes out to 3.0mm, 3.2mm deep. The leg, overall height, material and price are the same. See the drawing above.
Which way up does it go?
The leg goes into the slot and the head sits on the surface. With the tapered head, the sloping side is the lead-in edge, so face it towards the door or panel that closes onto it.
Can it be used inside an oven?
It is rated to +180°C continuous. It suits door frames, cabinet lids and warming or proving equipment where the seal stays at or below that temperature. For hotter positions, ask us about a higher-rated profile.
Is it safe near food or drinking water?
The compound is stated to meet FDA 21 CFR 177.2600 and EC 1935/2004 for food contact, and it is a WRAS approved material. We can send the declaration if your audit needs it.
How accurate are the dimensions?
The profile is extruded to ISO 3302-1 class E2, the normal tolerance class for extruded rubber sections. Check your slot against the drawing before ordering.
Will it flatten over time?
Silicone recovers well. This compound has a compression set of 34% after 22 hours at 175°C and 58% rebound resilience, so it keeps pushing back through repeated heat cycles.
What glue works with it?
Use a silicone adhesive or silicone sealant. Most general-purpose glues and contact adhesives will not bond to silicone rubber.
Can I buy a shorter length?
This listing is a full 25m coil. For a cut length or a large quantity, contact us for a quote.
Is every colour the same price?
Yes. All seven colours and both head shapes are £675.00 per 25m coil inc VAT, so you can colour-code by area at no extra cost.
Complete your project
- Silicone T Seal Profile – 4mm x 6.5mm (for slightly wider slots)
- Silicone T-Section Seal – 10mm x 10mm
- Silicone Round U Channel – 3mm x 5mm
Not sure which head shape suits your slot? Send us a photo or the slot size and we will check it for you. Contact our team.
Product details
| SKU | IP-SITS-3X6.5-SQ-25M-BLK |
|---|---|
| Weight | 1.1 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Silicone T Seal Profile – 3mm x 6.5mm – 25m Coil