Rubber & FoamSiliconeSKU IP-SITS-10X10-25M-BLACK
Silicone T Seal 10mm x 10mm – Soft 30 Shore A, 10 x 5mm Head, 5mm Leg – 25m Coil
A solid silicone T seal with a 10mm wide by 5mm deep head on a centred 5mm wide, 5mm long leg: 10mm tall overall. The leg pushes into a slot or panel joint and the head lies flat over the gap, giving a flush, flexible seal. Made in a very soft 30 Shore A compound, so it compresses easily into slightly undersized slots and recovers when released. Supplied as one continuous 25m coil in seven colours, held in stock.
At a glance
- Profile: T section, 10mm wide x 10mm high; head 10 x 5mm, leg 5 x 5mm
- Material: solid silicone rubber, soft 30 Shore A
- Temperature: -50°C to +180°C working range
- Food and water: FDA 21 CFR 177.2600, EC 1935/2004, WRAS approved
- Colours: black, white, translucent, red, green, blue, yellow (same price)
- Length: 25m coil, £675.00 inc VAT (£27.00 per metre inc VAT)
Technical drawing
![]()
Every dimension above comes from the manufacturer's datasheet. Values in brackets are derived (leg length 10 − 5 = 5mm; shoulder each side (10 − 5) ÷ 2 = 2.5mm).
Specifications
| Property | Value | Test method |
|---|---|---|
| Profile | Solid T section, leg centred | – |
| Overall width (head) | 10 mm | Datasheet drawing |
| Overall height | 10 mm | Datasheet drawing |
| Head depth (supplier: "base thickness") | 5 mm | Datasheet drawing |
| Leg width | 5 mm | Datasheet drawing |
| Leg length (derived) | 5 mm | 10 − 5 |
| Shoulder each side of leg (derived) | 2.5 mm | (10 − 5) ÷ 2 |
| Cross-section area (derived) | 75 mm² | 50 + 25 |
| Dimensional tolerance | Class E2 | ISO 3302-1:2014 |
| Coil length | 25 m, one continuous length | – |
| Approx. weight per coil (derived) | ≈ 2.1 kg | 75 mm² x 25 m x 1.10 g/cm³ |
| Compound | Silicone rubber | – |
| Hardness | 30° Shore A | DIN ISO 48-4 |
| Density | 1.10 g/cm³ | DIN EN ISO 1183-1 A |
| Tensile strength | 10 N/mm² (10 MPa) | ISO 37 Type 1 |
| Elongation at break | 910 % | ISO 37 Type 1 |
| Tear strength | 28 N/mm (28 kN/m) | ASTM D 624 B |
| Compression set, 22 h at 175°C | 20 % | DIN ISO 815-1 Type B Method A |
| Rebound resilience | 58 % | ISO 4662 |
| Working temperature | -50°C to +180°C | – |
| Environmental resistance | Ozone, UV, oxidation, weathering, corona discharge, cosmic and ionising radiation | Manufacturer statement |
| Colours | Black, white, translucent, red, green, blue, yellow | – |
All material values are the manufacturer's figures for this profile's 30 Shore A compound. "Derived" rows are our arithmetic from those figures.
Materials and compliance
The manufacturer states in writing, for this product:
- FDA 21 CFR 177.2600: rubber articles intended for repeated food contact
- EC 1935/2004: EU framework regulation for food-contact materials
- WRAS approved material, for use with drinking (potable) water
- Free from TSE/BSE animal by-products
- Free from phthalates
Only approvals the manufacturer states in text for this product are listed. Ask us for the declaration of conformity if you need it for an audit.
Typical uses
- Joint seal between stainless or painted steel panels on food lines and catering units
- Slot seal on oven, furnace, HVAC and heating enclosure panels up to +180°C
- Infill strip for T-slots and grooves in machine guards and enclosures
- Weather seal on hatches, frames and structural joints (UV and ozone resistant)
- Potable water and brewery equipment where WRAS approval is needed
- Colour-coded seals for food-safety zoning (blue, red, green, yellow)
Sizing and fitting
Our guidance (not a manufacturer figure): for a push fit, use a slot about 4–4.5mm wide and at least 5mm deep, so the soft 5mm leg is lightly squeezed and the head sits flat. A 5mm slot gives a free fit; add silicone adhesive to hold it. The 10mm head covers a gap up to about 5mm wide with 2.5mm of overlap each side.
- Clean and dry the slot or joint.
- Measure the run and cut the seal square with a sharp knife or shears. Allow 1–2% extra; soft silicone can stretch while fitting.
- For a permanent fix, run a thin bead of silicone adhesive or RTV sealant into the slot.
- Start at one end and press the leg fully home without pulling the strip tight, then smooth the head flat.
How much do I need?
Add up the length of every joint and allow about 2% for trimming. Eight 2.4m panel joints = 19.2m + 0.4m = 19.6m, so one 25m coil covers it. A 40m job needs two coils.
Frequently asked questions
What size slot does the 10mm x 10mm T seal fit?
The leg is 5mm wide and 5mm long. A slot 4–4.5mm wide and at least 5mm deep gives a firm push fit in this soft 30 Shore A silicone. That is our fitting guidance, not a manufacturer tolerance.
How do I fit it?
Press the leg into the slot by hand or with a plastic roller, working from one end, then smooth the head flat. Do not stretch the strip as you go. Add silicone adhesive in the slot for a permanent seal.
How do I cut and join it?
Cut with a sharp knife or shears on a cutting board; a mitre block helps at corners. Join ends or mitres with a silicone adhesive or RTV silicone sealant. General-purpose superglues do not bond silicone well without a primer.
Is it safe for food and drinking water?
Yes. The manufacturer states it meets FDA 21 CFR 177.2600 and EC 1935/2004 for food contact and is a WRAS approved material for potable water. It is also free from phthalates and TSE/BSE by-products.
What temperature can it take?
It works continuously from -50°C to +180°C. Compression set is 20% after 22 hours at 175°C, so it keeps sealing on hot panels.
How soft is 30 Shore A?
Very soft, a little firmer than a pencil eraser. It squeezes into undersized slots and seals uneven gaps well. If you need a stiffer infill that resists being pushed out, choose a 60 Shore A T seal.
Is it the same profile in every colour?
Yes. All seven colours use the same 10 x 10mm profile and the same 30 Shore A compound, at the same price. Blue, red, green and yellow are often used for food-safety colour coding.
Is it in stock and how long is the coil?
It is held in stock and sold as one continuous 25m coil. Need a different length or a large quantity? Contact our team or call +44 1282 277786.
Complete your project
Product details
| SKU | IP-SITS-10X10-25M-BLACK |
|---|---|
| Material | Silicone |
| Form | Profile |
| Weight | 4.63 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Silicone T Seal 10mm x 10mm – Soft 30 Shore A, 10 x 5mm Head, 5mm Leg – 25m Coil