Rubber & FoamSKU IP-SITS-4X6.1-25M-BLK
Silicone T Seal Profile – 4mm x 6.1mm – 25m Coil
A slim-legged solid silicone T seal for narrow slots around 1.3–1.4mm wide. The 1.4mm leg pushes into the slot and grips the walls along its full 4.1mm length, while the 4mm flat head sits on the surface and closes the gap against dust, splash, draughts and heat. Each order is one unbroken 25m coil, in any of seven colours.
At a glance
- Head 4.0mm wide × 2.0mm deep, with a flat face for the lid or door to close onto
- Leg 1.4mm wide × 4.1mm long: the thinnest leg in our 4mm-head T seal range, for narrow, deep slots
- 6.1mm overall height, with a 1.3mm shoulder each side of the leg
- Solid silicone rubber, 60 Shore A, working range -50°C to +180°C
- Compound stated to meet FDA 21 CFR 177.2600 and EC 1935/2004 for food contact; WRAS approved material
- Black, white, translucent, red, green, blue or yellow, all the same size and price
- Held in stock in every colour
Where it fits best
Most T seals with a 4mm head have a 2mm leg. This one has a 1.4mm leg, so it is the one to choose when your slot is too narrow for a 2mm leg to go in. The longer 4.1mm leg gives more grip in a deep slot, and the wide 1.3mm shoulders cover small gaps either side of the slot mouth.
- Narrow slot seals in aluminium extrusion frames, machine guards and enclosures
- Door and lid seals on catering cabinets, proving cabinets and warming units
- Inspection hatches and access panels on food and packaging machinery
- HVAC access doors, ducting panels and heater enclosures
- Colour-coded seals for hygiene zones (red, green, blue, yellow)
Technical drawing
![]()
Full specification
| Property | Value | Test method |
|---|---|---|
| Dimensions | ||
| Profile type | Solid T section, square-edged head | – |
| Overall height | 6.1 mm | – |
| Head width × depth | 4.0 mm × 2.0 mm | – |
| Leg (base) width | 1.4 mm | – |
| Leg length below head | 4.1 mm | – |
| Shoulder each side of leg | 1.3 mm | – |
| Suits slot | About 1.3–1.4 mm wide, at least 4.1 mm deep | – |
| Dimensional tolerance | Class E2 | ISO 3302-1:2014 |
| Approximate weight | 16 g per metre (about 0.4 kg per coil), calculated from section and density | – |
| Length per coil | 25 m, one continuous length | – |
| Material and physical properties | ||
| Compound | Solid silicone rubber | – |
| Hardness | 60 Shore A | DIN ISO 48-4 |
| Density | 1.15 g/cm³ | DIN EN ISO 1183-1, method A |
| Tensile strength | 11 N/mm² (11 MPa) | ISO 37, type 1 |
| Elongation at break | 550 % | ISO 37, type 1 |
| Tear strength | 26 N/mm (26 kN/m) | ASTM D624, die B |
| Compression set | 31 % after 22 h at 175 °C | DIN ISO 815-1, type B, method A |
| Rebound resilience | 59 % | ISO 4662 |
| Service conditions | ||
| Working temperature | -50 °C to +180 °C | – |
| Environmental resistance | Ozone, UV, oxidation, weathering, corona discharge, cosmic and ionising radiation | – |
| Supply | ||
| Colours | Black, white, translucent, red, green, blue, yellow | – |
| Unit of sale | 1 coil of 25 m (£27.00 per metre inc VAT) | – |
Materials and compliance
These are the claims the manufacturer makes in writing for this exact profile and compound. Ask us for the certificate or declaration your file needs.
| Claim | What it means for you |
|---|---|
| FDA 21 CFR 177.2600 | The compound meets the US rule for rubber articles in repeated contact with food. |
| EC 1935/2004 | The compound meets the EU framework regulation for materials that come into contact with food. |
| WRAS approved material | The material is accepted for contact with drinking water in UK water fittings. |
| Free from TSE/BSE by-products | No animal-derived ingredients that carry TSE/BSE risk. |
| Phthalate free | Made without phthalate plasticisers. |
Approvals cover the material as supplied. Whether your finished assembly complies also depends on its design, cleaning regime and the other materials in it, so check against your own requirements.
Will it fit my slot?
Measure the slot width and depth with a vernier or feeler gauge. The leg is 1.4mm wide, so it grips best in a slot of about 1.3–1.4mm. The slot needs to be at least 4.1mm deep so that the head sits down flat; a deeper slot is fine. Around the slot you need at least 1.3mm of flat surface each side for the head to rest on. If your slot is 1.8mm or wider, a T seal with a 2mm leg will hold better. In a slot that is slightly wide, run a thin bead of silicone adhesive along the bottom first so the leg cannot work loose.
How much do I need?
Add up the length of every slot and allow about 5% for trimming and joints. Example: a cabinet door 600mm × 1500mm sealed on all four sides needs 4.2m, or about 4.4m with allowance, so one 25m coil does five doors.
Fitting tips
- Clear old seal, grease and grit out of the slot and let it dry
- Start partway along a straight side, not at a corner
- Press the leg in with your thumb or a small plastic roller as you go; the thin leg goes in more easily if you feed it at a slight angle
- Lay the seal into corners rather than pulling it round: stretched silicone shrinks back and opens a gap
- Cut slightly long with a sharp knife and push the ends together; a dab of silicone adhesive keeps the joint closed
FAQ: frequently asked questions
What slot does this T seal need?
A slot about 1.3–1.4mm wide and at least 4.1mm deep, with about 1.3mm of flat face either side for the 4mm head to sit on. See the drawing above.
How is it different from the 4mm x 5mm T seal?
Both have a 4mm × 2mm head. The 4mm x 5mm seal has a 2.0mm × 3.0mm leg for wider, shallower slots. This 4mm x 6.1mm seal has a thinner 1.4mm leg that is longer at 4.1mm, for narrow, deeper slots.
Can it be used on oven and heater doors?
It is rated to +180°C continuous, so it suits proving cabinets, warming units, heater enclosures and door frames that stay at or below that temperature. For hotter positions, ask us about a higher-rated profile.
Is it safe near food or drinking water?
The compound is stated to meet FDA 21 CFR 177.2600 and EC 1935/2004 for food contact, and it is a WRAS approved material. We can send the declaration if your audit needs it.
How accurate are the dimensions?
The profile is extruded to ISO 3302-1 class E2, the normal tolerance class for extruded rubber sections. Check your slot against the drawing before ordering.
Will it flatten over time?
Silicone recovers well. This compound has a compression set of 31% after 22 hours at 175°C and 59% rebound resilience, so it keeps pushing back through repeated heat cycles.
How do I cut and join it?
Cut square with a sharp craft knife or fine shears on a cutting board. Butt the ends together at corners or joints and fix with a silicone adhesive or silicone sealant; most general-purpose glues and contact adhesives will not bond to silicone rubber.
Can I buy a shorter length?
This listing is a full 25m coil. For a cut length or a large quantity, contact us for a quote.
Is every colour the same price?
Yes. All seven colours are £675.00 per 25m coil inc VAT (£27.00 per metre), so you can colour-code by area at no extra cost.
Complete your project
- Silicone T Seal Profile – 4mm x 5mm (2mm leg, for wider, shallower slots)
- Silicone T Seal Profile – 4mm x 6.5mm (chamfered head)
- Silicone T Seal Profile – 4mm x 4.3mm (dovetail leg, serrated head)
Not sure it suits your slot? Send us a photo or the slot size and we will check it for you. Contact our team.
Product details
| SKU | IP-SITS-4X6.1-25M-BLK |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Silicone T Seal Profile – 4mm x 6.1mm – 25m Coil