Rubber & FoamSKU IP-SILT-4X8.5-BLACK
Silicone T Seal Profile – 4mm x 8.5mm – 25m Coil
This silicone T seal 4mm x 8.5mm presses into narrow slots and structural gaps to give a tight, flush barrier against moisture, dust and draughts. It is made from food-grade 60 Shore A silicone that stays flexible from -50°C to +180°C, and is sold as a continuous 25m coil in a choice of seven colours.
At a glance
- 4mm wide flange x 8.5mm overall height, 2.2mm stem
- Supplied as one continuous 25m coil
- Food-grade silicone rubber, FDA and WRAS approved
- Works from -50°C to +180°C
- Resists UV, ozone and outdoor weathering
- Black, white, translucent, red, green, blue or yellow
Typical uses
- Food processing lines, catering units and brewery equipment
- Panel joints on ovens, furnaces, HVAC ducting and heating enclosures
- Weatherproof hatch boundaries and windows on marine vessels
- Gap seal and rubber T trim for control cabinets and dashboard interfaces
Which one do I need?
| Profile | Best for |
|---|---|
| 4mm x 6.5mm T seal | Shallower slots where the seal must sit lower |
| 4mm x 8.5mm T seal (this item) | Narrow slots needing a deeper stem for extra grip |
| 5mm x 10mm T seal | Wider gaps and a larger domed sealing face |
| 6mm x 5.2mm T seal | Short, firm 80 Shore A stem for shallow tracks |
Technical drawing
Specification
| Material | Silicone (FDA and WRAS approved) |
| Width (flange) | 4mm |
| Overall height | 8.5mm |
| Stem thickness | 2.2mm |
| Hardness | 60° Shore A |
| Density | 1.15 g/cm³ |
| Tensile strength | 11 N/mm² |
| Elongation at break | 550% |
| Operating temperature | -50°C to +180°C |
| Unit of sale | 25m coil |
Installation and care
Clean the slot thoroughly and measure the length you need. Mark the cut with a non-permanent marker and cut square with a sharp utility knife or heavy-duty shears. If the joint vibrates or moves, run a bead of silicone adhesive into the slot first. Press the stem fully into the gap and smooth the flange flat along the edge so it makes even contact. Wipe clean with warm soapy water; avoid solvents.
Fitting tips
- Make sure the slot is free of dust, grease and swarf before fitting.
- Do not stretch the seal as you press it in, or it may shrink back later.
- Cut slightly long and trim to a tight butt joint at the ends.
- Allow adhesive to cure fully before exposing the joint to heat or water.
Complete your project
- Silicone T Seal Profile – 10mm x 8mm – 25m Coil
- Silicone T Seal Profile – 3mm x 6.5mm, 50° Shore A – 25m Coil
- Silicone Self-Grip Edge Trim 8.9 x 12.4mm – Fits 1–4mm Panels
Questions
Is this T seal suitable for food contact?
Yes. The silicone meets FDA 21 CFR 177.2600 and EC1935/2004 and is WRAS approved, so it suits food processing and drinking water equipment.
Can it be used outdoors?
Yes. Silicone resists UV, ozone and weathering without cracking or going brittle.
How do I cut the coil?
A sharp utility knife or heavy-duty shears gives a clean, square cut.
Does it need adhesive?
The stem grips by friction in a snug slot. For joints that vibrate or flex, a silicone adhesive in the slot is recommended.
Need help choosing the right gap seal? Contact our team for advice.
Product details
| SKU | IP-SILT-4X8.5-BLACK |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Silicone T Seal Profile – 4mm x 8.5mm – 25m Coil