Rubber & FoamSKU IP-SITS-4.5X8.5-H25-25M-BLK
Silicone T Seal Profile – 4.5mm x 8.5mm – 25m Coil
A solid silicone T seal with a 4.5mm-wide head and a 2.7mm leg, 8.5mm tall overall. Push the leg into a slot about 2.5–2.7mm wide and the head sits on the surface, closing the gap against dust, splash, draughts and heat. You can choose a 2.5mm or a 2.7mm head thickness, in any of seven colours. Every option is the same price, and each coil is one unbroken 25m length.
At a glance
- Head 4.5mm wide; leg 2.7mm wide; 8.5mm overall height
- Two head thicknesses: 2.5mm (6.0mm leg below the head) or 2.7mm (5.8mm leg below the head)
- 0.9mm shoulder each side of the leg, so the head covers both slot edges
- Solid silicone rubber, 70 Shore A, working range -50°C to +180°C
- The manufacturer states the compound meets FDA 21 CFR 177.2600 and EC 1935/2004 for food contact. It is a WRAS approved material.
- Black, white, translucent, red, green, blue or yellow, all at the same price
- Held in stock in every colour and both head thicknesses
2.5mm or 2.7mm head: which do I need?
| 2.5mm head | 2.7mm head | |
|---|---|---|
| Head | 4.5 × 2.5mm | 4.5 × 2.7mm |
| Leg below the head | 6.0mm | 5.8mm |
| Stands proud of the frame | 2.5mm | 2.7mm |
| Best for | Matching an existing 2.5mm seal, or where the door gap is tight | Matching an existing 2.7mm seal, or where you want a little more squeeze from the closing panel |
| Leg width, height, material, price | Identical: 2.7mm leg, 8.5mm overall, 70 Shore A silicone, £675.00 per 25m coil | |
Replacing an old seal? Measure the head of an offcut with a vernier caliper: if it is 2.5mm thick order 2.5mm, and if it is 2.7mm order 2.7mm. If you are designing a new joint, measure the gap between the closed door and the frame face. A head about 0.5–1mm thicker than that gap gives a good seal.
Typical uses
- Slot seals in machine guards, enclosures and aluminium profile frames
- Access doors on air handling units, fan housings and ductwork
- Inspection hatches on food, bakery and packaging machinery
- Lids and doors on ovens, provers, warming cabinets and dryers up to +180°C
- Marine hatches and outdoor enclosures, where UV and ozone crack other rubbers
- Colour-coded seals for hygiene zones (red, green, blue, yellow)
Technical drawing
![]()
Full specification
| Property | Value | Test method |
|---|---|---|
| Dimensions | ||
| Profile type | Solid T section, centred leg | – |
| Overall height | 8.5 mm | – |
| Head width | 4.5 mm | – |
| Head thickness | 2.5 mm or 2.7 mm (your choice) | – |
| Leg width (base thickness) | 2.7 mm | – |
| Leg length below head | 6.0 mm (2.5mm head) / 5.8 mm (2.7mm head), reference | – |
| Shoulder each side | 0.9 mm | – |
| Suits slot | Approx. 2.5–2.7 mm wide, at least 6 mm deep | – |
| Dimensional tolerance | Class E2 | ISO 3302-1:2014 |
| Length per coil | 25 m, one continuous length | – |
| Material and physical properties | ||
| Compound | Solid silicone rubber | – |
| Hardness | 70 Shore A | DIN ISO 48-4 |
| Density | 1.18 g/cm³ | DIN EN ISO 1183-1, method A |
| Tensile strength | 11.3 N/mm² (11.3 MPa) | ISO 37, type 1 |
| Elongation at break | 530 % | ISO 37, type 1 |
| Tear strength | 31 N/mm (31 kN/m) | ASTM D624, die B |
| Compression set | 40 % after 22 h at 175 °C | DIN ISO 815-1, type B, method A |
| Rebound resilience | 55 % | ISO 4662 |
| Service conditions | ||
| Working temperature | -50 °C to +180 °C | – |
| Environmental resistance | Ozone, UV, oxidation, weathering, corona discharge, cosmic and ionising radiation | – |
| Supply | ||
| Head thicknesses | 2.5 mm, 2.7 mm | – |
| Colours | Black, white, translucent, red, green, blue, yellow | – |
| Approx. weight | About 32–33 g per metre, about 0.8 kg per coil (calculated from section and density) | – |
| Unit of sale | 1 coil of 25 m (£27.00 per metre inc VAT) | – |
Materials and compliance
These are the claims the manufacturer makes in writing for this exact profile and compound. Ask us if your file needs the certificate or declaration.
| Claim | What it means for you |
|---|---|
| FDA 21 CFR 177.2600 | The compound meets the US rule for rubber articles in repeated contact with food. |
| EC 1935/2004 | The compound meets the EU framework regulation for materials that come into contact with food. |
| WRAS approved material | The material is accepted for contact with drinking water in UK water fittings. |
| Free from TSE/BSE by-products | No animal-derived ingredients that carry TSE/BSE risk. |
| Phthalate free | Made without phthalate plasticisers. |
The approvals cover the material as supplied. Whether your finished assembly complies also depends on its design, its cleaning regime and the other materials in it, so check it against your own requirements.
Will it fit my slot?
Measure the slot's width and depth. The leg is 2.7mm wide, so it grips best in a slot of about 2.5–2.7mm. The slot should be at least 6mm deep so the head can sit down flat on either version; a deeper slot is fine. If your slot is nearer 2.2mm wide, our 4mm × 8.5mm T seal with a 2.2mm leg is a closer fit.
How much do I need?
Add up the length of every slot and allow about 5% for trimming and joints. For example, a 600mm × 400mm guard door needs 2.0m, or about 2.1m with the allowance, so one 25m coil seals 11 doors of that size.
Fitting tips
- Clear any old seal, grease and grit out of the slot, and let it dry
- Start partway along a straight side, not at a corner
- Press the leg in with your thumb or a small plastic roller as you go
- Lay the seal into corners rather than pulling it round them. Stretched silicone shrinks back and opens a gap.
- Cut the end slightly long with a sharp knife and push the ends together; a dab of silicone adhesive keeps the joint closed
FAQ: frequently asked questions
What slot does it fit?
A slot about 2.5–2.7mm wide and at least 6mm deep. The head is 4.5mm wide, so it overlaps the slot by 0.9mm each side and covers the edges.
What is the difference between the 2.5mm and 2.7mm head?
Only the head thickness, and so how far the seal stands proud of the frame. The leg width, overall 8.5mm height, material and price are the same.
Which way up does it go?
The 2.7mm leg goes into the slot, and the wider head sits on the surface, facing the door, lid or panel it seals against.
Can it be used near ovens and heaters?
It is rated to +180°C continuous. That suits oven and warming-cabinet doors, drying equipment and heater housings, as long as the seal itself stays at or below that temperature. It stays flexible down to -50°C.
Is it safe near food or drinking water?
The manufacturer states the compound meets FDA 21 CFR 177.2600 and EC 1935/2004 for food contact, and it is a WRAS approved material. We can send the declaration if your audit needs it.
How accurate are the dimensions?
The profile is extruded to ISO 3302-1 class E2, the normal tolerance class for extruded rubber sections. Check your slot against the drawing before you order.
Will it flatten over time?
At 70 Shore A it is a firmer silicone that holds its shape. It has a compression set of 40% after 22 hours at 175°C and a rebound resilience of 55%, so it keeps sealing through repeated heat cycles.
How do I cut and join it?
Cut it with a sharp knife or shears. To join it, use a silicone adhesive or silicone sealant; most general-purpose glues and contact adhesives will not bond to silicone rubber.
Is every option the same price?
Yes. Both head thicknesses in all seven colours cost £675.00 per 25m coil inc VAT (£27.00 per metre).
Complete your project
- Silicone T Seal Profile – 4mm x 8.5mm (2.2mm leg)
- Silicone T Seal Profile – 3.6mm x 8.6mm
- Silicone T Seal Profile – 7.5mm x 6.5mm (wider head)
Not sure it will fit? Send us a photo, or the width and depth of the slot, and we will check it for you. Contact our team.
Product details
| SKU | IP-SITS-4.5X8.5-H25-25M-BLK |
|---|---|
| Weight | 1.98 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Silicone T Seal Profile – 4.5mm x 8.5mm – 25m Coil