Rubber & FoamSKU IP-SITS-6.2X5.2-25M-BLK
Silicone T Seal Profile – 6.2mm x 5.2mm – 60 Shore A – 25m Coil
A sturdy push-fit seal with a broad flat face for slots around 3.2mm wide. This silicone T seal profile is a solid 6.2mm x 5.2mm extrusion with a square-edged flat head (6.2mm wide, 2.1mm deep) on a thick 3.3mm wide, 3.1mm long leg. The heavy leg fills a wider slot than most T seals of this size and grips firmly, the head stands 2.1mm proud to give the closing face a 6.2mm contact band, and the 1.45mm shoulders cover the frame either side. At 60 Shore A it is a general-purpose silicone: soft enough to compress well under a closing door or lid, firm enough to keep its square shape, and with a low 31% compression set so it springs back after long periods shut at high temperature. Supplied as one continuous 25m coil in seven colours.
£675.00 inc VAT per 25m coil, which is £27.00 per metre.
At a glance
- Flat head 6.2mm wide and 2.1mm deep, square edges, 1.45mm shoulder each side of the leg
- Leg 3.3mm wide and 3.1mm long: a push fit in a slot about 3.1–3.3mm wide and at least 3.1mm deep
- Overall height 5.2mm; the head stands 2.1mm proud of the frame before compression
- Solid silicone, 60 Shore A, with 11 N/mm² tensile strength, 550% elongation and 26 N/mm tear strength
- Low compression set (31% after 22 h at 175°C) for good recovery on hot, long-closed doors
- Works from -50°C to +180°C without hardening or going brittle
- Food-contact compound (FDA 21 CFR 177.2600 and EC 1935/2004) and WRAS approved material
- 25m coil in black, white, translucent, red, green, blue or yellow, all the same price
Typical uses
- Door, lid and hatch seals on food processing, catering and brewing equipment
- Oven, dryer, steriliser and heated cabinet doors that stay shut at temperature
- HVAC access panels, air handling units and ducting covers
- Machine guards and enclosure panels with a slotted aluminium or stainless frame
- Infill and glazing seals in slotted frames
- Colour-coded seals for hygiene zones (blue, green, yellow, red)
Technical drawing
![]()
Full specification
| Property | Value | Test method |
|---|---|---|
| Dimensions | ||
| Profile type | Solid T section, flat square-edged head, straight leg | – |
| Overall width (head) | 6.2 mm | – |
| Overall height | 5.2 mm | – |
| Head depth | 2.1 mm | – |
| Leg (base) width | 3.3 mm | – |
| Leg length below head | 3.1 mm (reference, 5.2 − 2.1) | – |
| Shoulder overhang each side | 1.45 mm (reference, (6.2 − 3.3) ÷ 2) | – |
| Suggested slot | About 3.1–3.3 mm wide, at least 3.1 mm deep | Guidance |
| Dimensional tolerance | Extrusion tolerance class E2 | ISO 3302-1:2014 |
| Length per coil | 25 m, one continuous length | – |
| Material and physical properties | ||
| Material | Solid silicone rubber | – |
| Hardness | 60 Shore A | DIN ISO 48-4 |
| Density | 1.15 g/cm³ | DIN EN ISO 1183-1 A |
| Tensile strength | 11 N/mm² (11 MPa) | ISO 37 Type 1 |
| Elongation at break | 550 % | ISO 37 Type 1 |
| Tear strength | 26 N/mm | ASTM D624 B |
| Compression set | 31 % after 22 h at 175 °C | DIN ISO 815-1 Type B, Method A |
| Rebound resilience | 59 % | ISO 4662 |
| Service conditions | ||
| Working temperature | -50 °C to +180 °C | – |
| Environmental resistance | Ozone, UV, oxidation, weathering, corona discharge, cosmic and ionising radiation | – |
| Supply | ||
| Colours | Black, white, translucent, red, green, blue, yellow (same profile and price) | – |
| Unit of sale | 1 coil of 25 m (£27.00 per metre) | – |
| Approximate weight | About 0.67 kg per coil (calculated from cross-section and density) | Calculated |
Materials and compliance claims
These are the claims the manufacturer states for this exact profile and compound. Ask us for the certificate or declaration you need for your technical file.
| Claim | What it means for you |
|---|---|
| FDA 21 CFR 177.2600 | The compound meets the US rule for rubber articles intended for repeated contact with food. |
| EC 1935/2004 | The compound meets the EU framework regulation for materials intended to come into contact with food. |
| WRAS approved material | The material is listed as suitable for contact with drinking water in UK water fittings. |
| Free from TSE/BSE by-products | No animal-derived ingredients that carry TSE/BSE risk. |
| Phthalate free | Made without phthalate plasticisers. |
Approvals apply to the material as supplied. Whether a finished assembly complies also depends on your design, cleaning regime and other materials, so check against your own requirements.
Will it fit my groove?
This profile is made for a straight-sided slot about 3.1–3.3mm wide and at least 3.1mm deep. At 60 Shore A the leg squeezes into a slot slightly narrower than 3.3mm and grips well; in a slot of 3.3mm or wider, add a thin bead of silicone adhesive along the bottom. A deeper slot is fine, because the shoulders sit on the frame and set the height. The frame needs at least 1.5mm of flat land either side of the slot for the shoulders to sit on. If your slot is nearer 2mm wide, choose a T seal with a thinner leg.
![]()
How much do I need?
Measure every slot and add about 5% for trimming and joints. Example: a door with a 600mm x 450mm groove needs 2.1m, so one 25m coil does about 11 doors with allowance.
Fitting tips
- Clean old seal and debris out of the slot and let it dry
- Start in the middle of a long side, not at a corner
- Press the leg in with a plastic roller or the flat of a tool until the shoulders sit flat on the frame along the whole run
- Do not stretch the seal as you go: stretched silicone shrinks back and opens gaps at the joints
- Cut slightly long with a sharp knife or shears and push the ends together for a tight butt joint; a dab of silicone adhesive keeps it closed
FAQ: frequently asked questions
Which way up does it go?
The 3.3mm leg goes into the slot. The flat 6.2mm face of the head faces outwards, towards the door, lid or panel that closes onto it.
How big a gap does it close?
The head stands 2.1mm proud of the frame. As a guide, design for about 15–25% squeeze of the head, which is a closed gap of roughly 1.6–1.8mm between the frame and the closing face. More squeeze than that adds closing force without sealing better.
What slot size do I need?
A straight slot about 3.1–3.3mm wide and at least 3.1mm deep, with at least 1.5mm of flat frame either side. Check your slot against the drawing before ordering, or send us the dimensions and we will check it.
Is 60 Shore A soft or hard?
Medium, roughly like a pencil eraser or a car tyre tread. It compresses easily under a closing door yet holds its square shape. Its compression set is a low 31% after 22 hours at 175°C, so it recovers well on doors that stay shut at temperature.
Will it survive heat?
It is rated from -50°C to +180°C, so it suits ovens, warming cabinets, dryers and machinery that runs hot, as well as cold stores and freezers.
Is it safe near food or drinking water?
Yes. The compound is stated to meet FDA 21 CFR 177.2600 and EC 1935/2004 for food contact, and it is a WRAS approved material. Ask for the certificate if your audit needs it.
How do I cut and join it?
Cut square with a sharp knife or shears. Butt the ends together and bond with a silicone adhesive. For sharp corners, mitre and bond the ends rather than bending the seal tightly, which can lift the head.
Which colour should I choose?
All seven colours are the same compound, profile and price. Black and white are the usual choices for appearance; translucent shows dirt so cleaning is easy to check; red, green, blue and yellow suit colour-coded hygiene zones.
Can I order a shorter length or a different colour mix?
This listing is a full 25m coil in one colour. For cut lengths, mixed colours or larger quantities, contact us for a quote.
Complete your project
- Silicone T Seal Profile – 6mm x 5.2mm (40 or 80 Shore A)
- Silicone T Seal Profile – 6.1mm x 5mm (80 Shore A, thin leg)
- Silicone T Seal Profile – 6.1mm x 6.5mm (taller)
- Silicone T Seal Profile – 6mm x 6.5mm (deep leg)
Not sure this profile matches your slot? Send us a photo or the slot dimensions and we will check it. Contact our team.
Product details
| SKU | IP-SITS-6.2X5.2-25M-BLK |
|---|---|
| Weight | 1.76 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Silicone T Seal Profile – 6.2mm x 5.2mm – 60 Shore A – 25m Coil