Rubber & FoamSKU IP-SITS-7.5X6.5-25M-BLK
Silicone T Seal Profile – 7.5mm x 6.5mm – 25m Coil
A solid silicone T seal with a broad 7.5mm head and a stout 3.5mm leg. The leg pushes into a slot and holds the seal in place, while the wide head lies flat on the surface and covers the joint against dust, splash, steam, draughts and heat. The leg is set off-centre, so one side of the head reaches 2.7mm past the leg for extra cover at an opening edge. At 70 Shore A it is one of the firmer silicones in our T seal range. Each coil is one unbroken 25m length, offered in seven colours at the same price.
At a glance
- Head 7.5mm wide × 2.5mm deep; leg 3.5mm wide; 6.5mm overall height
- Off-centre leg: head overhangs 2.7mm on one side and about 1.3mm on the other
- Leg about 4.0mm long, for slots about 3.3–3.5mm wide and at least 4mm deep
- Solid silicone rubber, 70 Shore A, working range -50°C to +180°C
- Compound stated to meet FDA 21 CFR 177.2600 and EC 1935/2004 for food contact; WRAS approved material
- Black, white, translucent, red, green, blue or yellow: same size, same price
- Held in stock in every colour
Typical uses
- Door, lid and hatch seals on catering, bakery and food processing equipment
- Access panels on HVAC units, ducting, furnaces and heater enclosures
- Slotted aluminium extrusion frames, machine guards and enclosures
- Weatherproof hatch edges and panel joints on boats and buildings
- Colour-coded seals for hygiene zones (red, green, blue, yellow)
Technical drawing
![]()
![]()
Full specification
| Property | Value | Test method |
|---|---|---|
| Dimensions | ||
| Profile type | Solid T section, flat rectangular head, off-centre leg | – |
| Overall width (head) | 7.5 mm | – |
| Overall height | 6.5 mm | – |
| Head depth | 2.5 mm | – |
| Leg (base) width | 3.5 mm | – |
| Leg length below head | 4.0 mm (reference) | – |
| Head overhang, wide side | 2.7 mm | – |
| Head overhang, narrow side | 1.3 mm (reference) | – |
| Suggested slot | 3.3–3.5 mm wide, at least 4.0 mm deep | – |
| Dimensional tolerance | Class E2 | ISO 3302-1:2014 |
| Length per coil | 25 m, one continuous length | – |
| Material and physical properties | ||
| Compound | Solid silicone rubber | – |
| Hardness | 70 Shore A | DIN ISO 48-4 |
| Density | 1.18 g/cm³ | DIN EN ISO 1183-1, method A |
| Tensile strength | 11.3 N/mm² (11.3 MPa) | ISO 37, type 1 |
| Elongation at break | 530 % | ISO 37, type 1 |
| Tear strength | 31 N/mm (31 kN/m) | ASTM D624, die B |
| Compression set | 40 % after 22 h at 175 °C | DIN ISO 815-1, type B, method A |
| Rebound resilience | 55 % | ISO 4662 |
| Service conditions | ||
| Working temperature | -50 °C to +180 °C | – |
| Environmental resistance | Ozone, UV, oxidation, weathering, corona discharge, cosmic and ionising radiation | – |
| Supply | ||
| Colours | Black, white, translucent, red, green, blue, yellow | – |
| Approximate weight | About 1.0 kg per 25 m coil (calculated from section and density) | – |
| Unit of sale | 1 coil of 25 m (£27.00 per metre inc VAT) | – |
Materials and compliance
These are the claims the manufacturer makes in writing for this exact profile and compound. Ask us for the certificate or declaration your file needs.
| Claim | What it means for you |
|---|---|
| FDA 21 CFR 177.2600 | The compound meets the US rule for rubber articles in repeated contact with food. |
| EC 1935/2004 | The compound meets the EU framework regulation for materials that come into contact with food. |
| WRAS approved material | The material is accepted for contact with drinking water in UK water fittings. |
| Free from TSE/BSE by-products | No animal-derived ingredients that carry TSE/BSE risk. |
| Phthalate free | Made without phthalate plasticisers. |
Approvals cover the material as supplied. Whether your finished assembly complies also depends on its design, cleaning regime and the other materials in it, so check against your own requirements.
Will it fit my slot?
Measure the slot width and depth. The leg is 3.5mm wide, so it grips best in a slot of about 3.3–3.5mm, where it is lightly squeezed. The slot should be at least 4.0mm deep so the head can sit down flat; if it is shallower, trim the leg to suit. In a slot that is slightly wide, run a thin bead of silicone adhesive along the bottom first so the leg cannot work loose. Because the leg is off-centre, decide which edge needs the most cover before you start and keep the 2.7mm wide side of the head on that edge all the way round.
How much do I need?
Add up the length of every slot and allow about 5% for trimming and joints. Example: a hatch with a 600mm × 400mm seal track needs 2.0m, or about 2.1m with allowance, so one 25m coil seals 11 hatches.
Fitting tips
- Clear old seal, grease and grit out of the slot and let it dry
- Check the orientation of the off-centre leg, then start partway along a straight side, not at a corner
- Press the leg in with your thumb or a small plastic roller as you go, until the head lies flat
- Lay the seal into corners rather than pulling it round: stretched silicone shrinks back and opens a gap
- Cut slightly long with a sharp knife and push the ends together; a dab of silicone adhesive keeps the joint closed
FAQ: frequently asked questions
What slot does it suit?
A slot about 3.3–3.5mm wide and at least 4.0mm deep. The 3.5mm leg goes into the slot and the 7.5mm head covers the opening and the surface either side.
Why is the leg off-centre?
The head reaches 2.7mm past the leg on one side and about 1.3mm on the other. That lets you put the wider lip over a gap or an opening edge while keeping the narrow side tight against a return or upstand.
How is it different from your other silicone T seals?
It has the widest head and thickest leg of our small silicone T seals, and a firmer 70 Shore A compound. Choose it for wider slots, for joints that need a broad cover strip, or where a softer seal would be pushed out of shape.
Can it be used near ovens and heaters?
It is rated to +180°C continuous and down to -50°C. It suits door frames, proving and warming cabinets, ducting and heater enclosures where the seal stays within that range. For hotter positions, ask us about a higher-rated profile.
Is it safe near food or drinking water?
The compound is stated to meet FDA 21 CFR 177.2600 and EC 1935/2004 for food contact, and it is a WRAS approved material. We can send the declaration if your audit needs it.
How accurate are the dimensions?
The profile is extruded to ISO 3302-1 class E2, the normal tolerance class for extruded rubber sections. Check your slot against the drawing before ordering.
Will it flatten over time?
Silicone recovers well. This compound has a compression set of 40% after 22 hours at 175°C and 55% rebound resilience, so it keeps pushing back through repeated heat cycles.
How do I cut and join it?
Cut square with a sharp craft knife or shears. Butt the ends together and bond them with a silicone adhesive or sealant; most general-purpose glues and contact adhesives will not bond to silicone rubber.
Can I buy a shorter length?
This listing is a full 25m coil. For a cut length or a large quantity, contact us for a quote.
Is every colour the same price?
Yes. All seven colours are £675.00 per 25m coil inc VAT (£27.00 per metre), so you can colour-code by area at no extra cost.
Complete your project
- Silicone T Seal Profile – 3.6mm x 8.6mm (narrow, deep leg)
- Silicone T Seal Profile – 4mm x 6.5mm
- Silicone T-Section Seal – 10mm x 10mm (larger)
Not sure it will fit? Send us a photo or the slot size and we will check it for you. Contact our team.
Product details
| SKU | IP-SITS-7.5X6.5-25M-BLK |
|---|---|
| Weight | 2.43 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Silicone T Seal Profile – 7.5mm x 6.5mm – 25m Coil