Rubber & FoamSKU IP-SILT-12X7-BLACK
Silicone T Seal Profile – 12mm x 7mm, Food Grade – 25m Coil
This silicone T seal 12mm x 7mm has a 12mm wide flat head and a tapered leg that presses into a narrow slot or panel gap, leaving a neat, flush, food-safe seal. It is made from 80 Shore A silicone and sold as one continuous 25m coil in a choice of seven colours.
At a glance
- Silicone T profile: 12mm head width x 7mm total height
- Head 2.2mm thick at the centre, leg widening from 3.6mm to 4.5mm at the base for a firm grip in the slot
- Firm 80 Shore A silicone rubber edge seal that resists being pulled out
- Food contact compliant to FDA 21 CFR 177.2600 and EC 1935/2004; WRAS approved
- Works from -50°C to +180°C and resists UV, ozone and weathering
- Black, white, translucent, red, green, blue or yellow
Typical uses
- Gap seal between stainless steel panels on food processing and catering equipment
- Trim seals on commercial refrigeration and warming cabinets
- Access door and damper seals on HVAC and fan coil housings
- Hatch and window infill seals on boats and specialist vehicles
- Colour-coded rubber T strip for hygiene zones
Which one do I need?
| Profile (head x height) | Best for |
|---|---|
| 12mm x 7mm (this one) | Shallow slots where the seal must sit low and flush; tapered leg locks in |
| 12mm x 8mm | Slightly deeper slots with the same 12mm head cover |
| 12mm x 9.5mm | Deeper slots, 3mm head and leg |
| 12mm x 10.5mm | Deepest slots in the 12mm head range |
Technical drawing
Specification
| Profile | Solid T section |
| Material | Silicone rubber |
| Head width | 12mm |
| Total height | 7mm |
| Head thickness | 2.2mm at centre, 1.9mm at edge |
| Leg width | 3.6mm at head, 4.5mm at base |
| Hardness | 80 Shore A |
| Operating temperature | -50°C to +180°C |
| Density | 1.20 g/cm³ |
| Tensile strength | 10 N/mm² |
| Elongation at break | 440% |
| Approvals | FDA 21 CFR 177.2600, EC 1935/2004, WRAS |
| Colours | Black, white, translucent, red, green, blue, yellow |
| Unit of sale | One continuous 25m coil |
How much do I need?
Measure every run of gap or slot you want to seal and add 5% for trimming. For example, a cabinet with four 1.8m vertical joints and two 0.9m horizontal joints needs 4 x 1.8 + 2 x 0.9 = 9m, plus 5% = about 9.5m, so one 25m coil covers it with plenty left for a second unit.
Fitting tips
- Check the slot is between about 3.5mm and 4.5mm wide so the tapered leg grips without being forced.
- Clean and degrease the slot; old sealant or grease stops the leg seating fully.
- Press the leg in a little at a time without stretching the rubber, or it will shrink back and leave gaps at the ends.
- Cut ends square with a sharp knife; for a permanent fit add a bead of silicone adhesive in the slot.
Complete your project
- Silicone T Profile – 12mm x 8mm Head – 25m Coil
- Silicone T Profile – 11mm x 11.4mm – 25m Coil
- Silicone T Profile – 12mm x 10.5mm – 25m Coil
Questions
Is this silicone T seal food safe?
Yes. The silicone complies with FDA 21 CFR 177.2600 and EC 1935/2004 for food contact and is WRAS approved for drinking water.
What slot width does the 12mm x 7mm T seal fit?
The leg is 3.6mm wide under the head and 4.5mm at the base, so it suits slots of roughly 3.5mm to 4.5mm.
Can I use this rubber T strip outdoors?
Yes. Silicone resists UV, ozone and weathering and stays flexible from -50°C to +180°C.
Can I buy less than 25m?
This profile is sold as one continuous 25m coil, which avoids joints along long runs.
Need more help? Contact our team for advice.
Product details
| SKU | IP-SILT-12X7-BLACK |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Silicone T Seal Profile – 12mm x 7mm, Food Grade – 25m Coil