
Rubber & FoamSKU IP-EPDMP-19X3.5-14
Solid EPDM P Extrusion – 19mm x 3.5mm Bead, Tapered Tail – Black – 14m to 30m Coil
Price shown updates with the option you pick.
A slim P seal in solid black EPDM rubber: a solid Ø3.5 mm round bead with a 16 mm tail that tapers to a 1 mm rounded tip, 19 mm wide overall. Bond or fix the tail to a frame, rebate or panel edge and the bead closes small, even gaps on doors, windows, hatches and glazing. It also works as a neat cushioning edge trim. Choose a cut length from 14 m to 29 m in one continuous piece, or a full 30 m coil at a much lower price per metre. Held in stock for fast dispatch.
At a glance
- Size: 19 mm wide × 3.5 mm high; Ø3.5 mm solid bead; 16 mm tail tapering to 1 mm
- Material: solid (dense, non-sponge) EPDM, 65–75° Shore A
- Temperature: −40 °C to +90 °C
- Weather: no ozone cracking in the manufacturer's 72-hour ozone test; suits indoor and outdoor use
- Fixing: adhesive along the tail, or a mechanical fixing or retaining strip over the tail
- Weight: 0.05 kg per metre, so it adds almost nothing to a lightweight door or panel
- Supplied: 14 m to 29 m cut lengths in one piece (£14.85/m), or a 30 m full coil (£10.69/m, the best value from 22 m upwards)
Technical drawing

Specifications
| Property | Value | Test condition / method |
|---|---|---|
| Profile | P section: solid round bead with a tapered flat tail | - |
| Overall width | 19.0 mm | Manufacturer drawing |
| Overall height (bead diameter) | 3.5 mm (Ø3.5 mm solid bead) | Manufacturer drawing |
| Tail length | 16.0 mm (bead to tail tip) | Manufacturer drawing |
| Tail thickness at tip | 1.0 mm, rounded | Manufacturer drawing and data |
| Tail form | Tapers from the bead to the tip, on the bead centreline | Manufacturer drawing |
| Material | Solid ethylene propylene diene monomer (EPDM) rubber | - |
| Colour | Black | - |
| Hardness | 65–75° Shore A (data sheet: 65–75 IRHD) | Method not stated |
| Tensile strength | 10 MPa (10 N/mm²) | Method not stated |
| Elongation at break | 500% | Method not stated |
| Tear strength | 50 kN/m | Method not stated |
| Compression set | 21% | 22 hours at 70 °C |
| Ozone resistance | No cracks | 72 hours at 40 °C, 22 pphm ozone, extended |
| Heat ageing: hardness change | 0 IRHD | 70 hours at 70 °C |
| Heat ageing: tensile change | +9% | 70 hours at 70 °C |
| Heat ageing: elongation change | 0% | 70 hours at 70 °C |
| Service temperature | −40 °C to +90 °C | Manufacturer rating |
| Weight | 0.05 kg per metre (50 g/m; about 1.5 kg per 30 m coil) | Manufacturer data |
| Density | About 1.1–1.4 g/cm³ (typical for solid EPDM, not tested on this profile) | - |
| Dimensional tolerance | Not stated by the manufacturer. Extruded rubber is commonly made to ISO 3302-1 class E2 (typical for EPDM extrusions, not tested on this profile) | - |
| Supplied as | Cut lengths 14–29 m (one continuous piece) or a 30 m full coil | - |
| Price per metre | £14.85/m inc VAT on cut lengths; £10.69/m on the 30 m coil (£320.76) | - |
The manufacturer does not name the test standards behind its figures, so we show the test conditions it gives and mark the method "not stated". All sizes are nominal.
Materials and compliance
Solid EPDM is a general-purpose synthetic rubber with very good resistance to weathering, UV, ozone, water and steam. The manufacturer's heat-ageing results (no change in hardness or elongation after 70 hours at 70 °C) and its ozone test show it keeps its properties well outdoors. Like all EPDM it is not suitable for contact with oils, fuels or most solvents.
The manufacturer does not state any food-contact (FDA, EC 1935/2004), drinking-water (WRAS), REACH, RoHS or fire-rating approval for this profile, so we do not claim any. If your job needs certified material, ask us before you order.
How to fit it
- Check the land and the gap. You need a surface or rebate about 16 mm wide for the tail. The closed gap at the bead should be a little under 3.5 mm, about 2.5 to 3 mm, so the bead is lightly squeezed. This is our guidance, not a manufacturer figure.
- Clean the surface. Degrease with a solvent wipe and let it dry fully.
- Bond or fix the tail. Apply a contact adhesive suited to EPDM to the tail and the frame, wait until touch-dry, then press it down firmly. Or trap the tail under a glazing bead, trim strip or panel edge.
- Face the bead to the opening edge so the door, sash or glass lands on it.
- Corners and joints. Lay it on without stretching. Ease it round bends, or mitre-cut sharp corners and butt the ends tight.
Which size do I need?
| P seal | Bead | Best for |
|---|---|---|
| 13 × 2.5 mm | Solid, 2.5 mm | Very small gaps of about 1.5–2 mm and narrow frames |
| 19 × 3.5 mm (this seal) | Solid, 3.5 mm | Small, even gaps of about 2.5–3 mm; tail tucks under a trim or glazing bead |
| 28.5 × 3.5 mm | Solid, 3.5 mm | Same bead with a wider tail for more bonding area |
| 15 × 6 mm | Hollow, 6 mm | Larger or uneven gaps that need a softer squeeze |
How much to order: measure round every opening and add about 5% for trimming. For example, four hatches of 1200 × 800 mm need 4 × 4.0 m = 16 m, plus 5% = 16.8 m, so choose 17 m. From 22 m upwards the 30 m full coil costs less than a cut length.
Typical uses
- Door and window seal on frames, sashes and cabinet doors with a small gap
- Glazing and panel welt: tail trapped under a bead or trim, bead against the glass or panel
- Weatherstrip for inspection hatches, access panels and enclosure lids
- Vehicle, trailer, transport and marine doors, windows and lockers
- Decorative piping, edge trim and light impact cushioning between panels
FAQ
Is the bead hollow or solid?
Solid. A solid 3.5 mm bead gives a firm, even seal on small gaps and is hard to crush permanently. For larger or uneven gaps choose a hollow-bead P seal.
What size gap will it seal?
The bead is 3.5 mm, so it suits closed gaps of about 2.5 to 3 mm, where it is squeezed by roughly 0.5 to 1 mm. If the gap is 3.5 mm or more it will not seal; choose a larger profile.
How do I fix it?
Bond the 16 mm tail with a contact adhesive suited to EPDM, or trap it under a glazing bead, trim strip or panel edge. Because the tail thins to 1 mm, it sits almost flush once it is held down.
Can I use it outdoors?
Yes. EPDM resists UV, ozone and weathering, and this compound showed no cracks in the manufacturer's 72-hour ozone test. It is rated from −40 °C to +90 °C.
Will it go round corners?
Yes. It is light and flexible and will follow curves and bends. For sharp 90° corners, mitre-cut the seal and butt the ends together. Do not stretch it, or it will shrink back and open a gap.
How do I cut and join it?
Cut cleanly with a sharp knife or scissors. Butt-join the ends tightly, and add a dab of instant adhesive (cyanoacrylate) for a permanent join.
Is it resistant to oil or fuel?
No. EPDM swells in oils, fuels and most solvents. For oily areas use a neoprene or nitrile profile instead.
What is the minimum order?
This profile is cut from 30 m coils, so the shortest length we sell is 14 m. From 22 m upwards the full 30 m coil costs less than a cut length.
Is it food safe or WRAS approved?
No food-contact or WRAS approval is stated for this profile. Please contact us if you need a certified material.
Need help choosing? Call +44 1282 277786 or email sales@industrial-polymers.co.uk.
Product details
| SKU | IP-EPDMP-19X3.5-14 |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Solid EPDM P Extrusion – 19mm x 3.5mm Bead, Tapered Tail – Black – 14m to 30m Coil