
Rubber & FoamSKU IP-EPDMP-15X6-16
EPDM P-Section Extrusion – 15mm x 6mm Hollow Bead, Black – 16m to 30m Lengths
Price shown updates with the option you pick.
A neat black EPDM rubber P-section: a hollow 6 mm sealing bead on a flat 2 mm flange, 15 mm wide overall, cut to the length you choose from 16 m to a full 30 m coil. Fix the flange to a frame, rebate or panel edge and the hollow bead squeezes down when a door, hatch or lid closes on it, closing the gap against draughts, rain, dust and rattles. Solid (dense) EPDM shrugs off sunlight, ozone and weather, so it works just as well outside as in.
At a glance
- Size: 15 mm wide × 6 mm high; Ø6 mm hollow bead plus a 9 mm × 2 mm fixing flange
- Material: solid (dense, not sponge) EPDM rubber, 65–75 IRHD (about 65–75 Shore A), black
- Seals gaps: best on closed gaps of about 4 to 5 mm (our guidance)
- Temperature: −40 °C to +90 °C
- Outdoors: no cracking in a 72-hour ozone test; good UV and weather resistance
- Fixing: contact adhesive, instant adhesive or screws, rivets or staples through the flange
- Supplied as: one continuous length from 16 m to 30 m. The full 30 m coil is the best value at £8.76 per metre inc VAT
- Stock: held in stock in the UK and dispatched from stock
Typical uses
- Door, hatch and locker seals on vans, trailers, horseboxes, buses and rail interiors
- Weather seals on boat hatches, lockers and cabin doors
- Draught and dust seals on cabinet doors, enclosures, machine guards and access panels
- Window and glazing-frame seals on sheds, workshops, garden rooms and kiosks
- Edge trim and anti-rattle buffer between metal, timber and plastic panels
- Light impact strip on the edges of lids, flaps and trolleys
Technical drawing

Specifications
| Property | Value | Test method / basis |
|---|---|---|
| Profile type | P-section: round hollow bead with a flat side flange | Manufacturer's profile drawing |
| Overall width (bead edge to flange tip) | 15.0 mm | Nominal, manufacturer's drawing |
| Overall height (bead diameter) | Ø6.0 mm | Nominal, manufacturer's drawing |
| Free flange length (beyond the bead) | 9.0 mm | Nominal, manufacturer's drawing |
| Flange thickness | 2.0 mm | Nominal, manufacturer's drawing |
| Hollow bore / bead wall | About Ø3 mm / about 1.5 mm | Scaled from the manufacturer's drawing; not separately stated |
| Material | Solid (dense) EPDM (ethylene propylene diene monomer) | Manufacturer product page and datasheet |
| Colour | Black | - |
| Hardness | 65–75 IRHD (stated as 65°–75° Shore A on the product page) | IRHD; test standard not stated |
| Tensile strength | 10 MPa | Manufacturer datasheet; method not stated |
| Elongation at break | 500% | Manufacturer datasheet; method not stated |
| Tear strength | 50 kN/m | Manufacturer datasheet; method not stated |
| Compression set | 21% | 22 hours at 70 °C (manufacturer datasheet) |
| Ozone resistance | No cracks | 72 hours at 40 °C, 22 pphm ozone, extended (manufacturer datasheet) |
| Heat ageing: hardness change | 0 IRHD | 70 hours at 70 °C (manufacturer datasheet) |
| Heat ageing: tensile change | +9% | 70 hours at 70 °C (manufacturer datasheet) |
| Heat ageing: elongation change | 0% | 70 hours at 70 °C (manufacturer datasheet) |
| Maximum service temperature | +90 °C | Manufacturer product page |
| Minimum service temperature | −40 °C | Manufacturer product page |
| Weight | 0.057 kg per metre (about 1.71 kg for a 30 m coil) | Manufacturer product page |
| Density | Not stated for this profile. Solid EPDM is typically about 1.1 to 1.4 g/cm³ (typical for solid EPDM, not tested on this profile) | Ask us if you need it |
| Dimensional tolerance | Not stated by the manufacturer. Treat sizes as nominal; solid extrusions are commonly made to ISO 3302-1 Class E2 (typical, not stated for this profile) | Ask us if your fit is critical |
| Lengths available | 16 m to 30 m in 1 m steps, supplied in one continuous piece | - |
| Price per metre | £11.73/m inc VAT on 16 m to 29 m; £8.76/m inc VAT on the full 30 m coil | - |
The manufacturer quotes hardness as 65–75 IRHD on its data sheet and 65°–75° Shore A on its product page; for rubber in this range the two scales read very close. Rubber extrusions are flexible, so treat all sizes as nominal.
Materials and compliance
Solid EPDM rubber, black. EPDM is valued for its resistance to weather, sunlight (UV), ozone, water and steam, and it stays flexible down to −40 °C. The manufacturer's ozone test on this compound shows no cracking, and 70 hours at 70 °C left its hardness and elongation unchanged. Like all EPDM it is not suited to petrol, diesel, mineral oils or most solvents.
The manufacturer does not state any food-contact (FDA, EC 1935/2004), drinking-water (WRAS), REACH, RoHS or fire-rating approval for this profile, so we do not claim any. If your job needs a certified material, ask us before you order.
How it fits

- Measure the closed gap. It must be less than 6 mm so the bead is squeezed. About 4 to 5 mm (around 15 to 35% squeeze) is a good starting point; this is our guidance, not a manufacturer figure.
- Check the landing. You need a flat face at least 15 mm wide, or a rebate the 9 mm flange can sit in, with the bead facing the closing part.
- Clean and dry. Wipe the surface and the back of the flange with isopropyl alcohol and let them dry.
- Fix the flange. Use a rubber-compatible contact adhesive or instant adhesive along the flange, or screws, rivets or staples every 100 to 150 mm through the flange. Keep fixings clear of the bead.
- Do not stretch it. Lay it in relaxed; stretched rubber shrinks back over time and opens gaps at the ends.
- Corners and joins. It follows gentle curves. For a tight 90° corner, cut a V-notch in the flange or mitre and butt the ends. A spot of instant adhesive on butted ends gives a sealed join.
How much do I need?
Add up every edge you want to seal and allow about 5% for trimming. A standard 2 m × 0.8 m door needs about 5.6 m round the frame (three sides about 4.8 m), so a 16 m length does three doors and a 30 m coil does five. Need more than 30 m? Add two lengths to your basket, or call us for a quote on longer runs.

Which profile do I need?
| Profile | Size | Best for |
|---|---|---|
| EPDM P-section (this item) | 15 mm × Ø6 mm hollow bead | Closed gaps of about 4 to 5 mm, weather-proof, −40 to +90 °C |
| Solid EPDM P extrusion | 13 mm × 2.5 mm solid bead | Piping and very small gaps, sold per metre |
| EPDM P profile | 19.5 mm × 7.5 mm bulb | Slightly larger gaps of about 5 to 6 mm |
| TPE P profile | 16 mm × 6 mm hollow bulb | Similar size in TPE, 25 m coil |
| High-temperature silicone P extrusion | 15 mm × 6 mm hollow bead | Same shape for ovens, dryers and hot equipment |
Data sheet
Download the technical data sheet (PDF): drawing, full specification and compliance
Questions
What gap will it seal?
Any closed gap under its 6 mm bead height. Aim for about 4 to 5 mm so the hollow bead is squeezed but not flattened. For bigger gaps choose the 19.5 × 7.5 mm P profile.
How do I fix it?
It has no self-adhesive tape. Bond the 9 mm flange with a contact or instant adhesive suitable for EPDM, or fix it mechanically with screws, rivets or staples through the flange. Clean surfaces first.
Which way round does it go?
The flange goes against the frame, rebate or panel and the round bead faces the door, hatch or lid that closes on it. In a rebate, tuck the flange in and leave the bead standing proud.
How do I cut and join it?
Sharp scissors, a craft knife or a rubber cutter gives a clean square end. Butt joins tightly and glue the ends with instant adhesive for a sealed join; mitre the ends at corners.
What temperatures can it take?
The manufacturer rates it from −40 °C to +90 °C. For hotter jobs such as ovens and dryers, use the silicone P extrusion of the same size.
Can I use it outdoors?
Yes. Solid EPDM has very good UV, ozone and weather resistance; this compound showed no cracks in a 72-hour ozone test.
Will it stand up to oil or fuel?
No. EPDM handles water, steam, weather and many dilute chemicals well, but swells in oils, fuels and most solvents. Ask us for a neoprene or nitrile alternative.
Is it sponge or solid rubber?
Solid (dense) rubber at 65–75 IRHD. The bead is hollow, which lets it compress easily, but the rubber itself is not foam, so it is tougher and more hard-wearing than a sponge seal.
Why is the 30 m coil cheaper than 29 m?
Lengths of 16 to 29 m are cut from a coil to order; 30 m is a full uncut coil, so we pass the saving on. If you need more than about 22 m, the full coil costs less.
Is it food-safe or WRAS approved?
No approvals are stated for this profile, so do not use it where certified food-contact or drinking-water material is required.
Delivery and help
Held in stock and dispatched from the UK. Trade and quantity orders welcome. Not sure it is the right profile? Call +44 1282 277786 or email sales@industrial-polymers.co.uk and we will check it for you.
Product details
| SKU | IP-EPDMP-15X6-16 |
|---|---|
| Weight | 2.01 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:EPDM P-Section Extrusion – 15mm x 6mm Hollow Bead, Black – 16m to 30m Lengths