
Rubber & FoamSKU IP-TPEF-110X95X2-BLACK
TPE Delta D Fender – 110mm x 95mm – 2 x 5m Pack
Price shown updates with the option you pick.
This hollow TPE delta D fender, 110mm x 95mm, is a triangular-section rubbing strip for pontoons, jetties, workboats and loading bays, sold as a pack of two 5m lengths (10m in total) in black or grey. The wide flat back fixes against the structure while the hollow peak flexes on impact and spreads the load into the base.
At a glance
- Delta D fender profile: 110mm across the flat back, 95mm deep from back to peak
- Hollow core gives a softer, more forgiving bump than a solid fender of the same size
- Thermoplastic elastomer (TPE), 68 Shore A, non-marking on boat hulls and painted vehicles
- Good UV, weather, abrasion and tear resistance for permanent outdoor fitting
- Works from -40°C to +90°C
- Black or grey, two 5m lengths per pack for easier handling, 100% recyclable
Typical uses
- Edge protection along marina pontoons, jetties and landing stages
- Rubbing strip on workboats, ribs and harbour craft
- Impact strip on lorry loading bays, dock edges and goods-in doors
- Bumper strip for walls and columns in busy industrial areas
Which one do I need?
| Delta D fender size | Best for |
|---|---|
| 60mm x 52mm | Small boats, tenders and light-duty fingers |
| 80mm x 70mm | General marina pontoons, medium workboats and loading bay edges |
| 110mm x 95mm (this product) | Larger vessels, busy berths and heavier quay or dock impacts |
| 150mm x 130mm | Commercial berths and heavy dock protection |
Technical drawing
Specification
| Profile | Hollow delta D (triangular) fender with flat fixing back |
| Size | 110mm wide x 95mm deep |
| Material | Thermoplastic elastomer (TPE) |
| Hardness | 68 Shore A |
| Density | 1.09 g/cm³ |
| Tensile strength | 7.8 MPa |
| Elongation at break | 700% |
| Operating temperature | -40°C to +90°C |
| Tolerance | ISO 3302-1 E2 / L2 |
| Colours | Black, grey |
| Unit of sale | One pack of two 5m lengths (10m) |
How much do I need?
Measure every edge you want to protect and add about 5% for trimming at the ends and corners. Example: a 12m pontoon with one 6m finger needs 18m, plus 5% = 18.9m, so order two packs (20m) of the 110mm x 95mm fender.
Fitting tips
- Fix through the flat back with stainless screws and penny washers at roughly 250-300mm centres, closer at the ends.
- Pre-drill the fixing holes so the profile does not distort as screws are tightened.
- Cut cleanly with a sharp knife or fine saw; mitre the ends at corners for a neat finish.
Complete your project
- Hollow TPE Delta D Fender – 80mm x 70mm – 10m Coil
- Hollow TPE Delta D Fender – 60mm x 52mm – 10m Coil
- TPE B Fender – Solid 80mm x 40mm – 25m Coil
Questions
What is a delta D fender?
It is a fender with a triangular, D-like cross-section: a wide flat back that fixes to the structure and a narrower peak that takes the knocks.
Will the 110mm x 95mm fender mark my boat?
No. The TPE compound is non-marking, so it will not leave black streaks on gelcoat or paintwork.
Should I choose 110mm x 95mm or 80mm x 70mm?
Choose 110mm x 95mm for larger vessels and heavier impacts, where the deeper hollow gives more cushioning. The 80mm x 70mm size suits general pontoons and medium workboats; the 150mm x 130mm size suits commercial berths.
Why is it supplied as two 5m lengths?
A large-section fender is heavy and stiff in a single coil, so two 5m lengths are easier to carry, store and fit.
Need help choosing a fender? Contact our team and we will be glad to help.
Product details
| SKU | IP-TPEF-110X95X2-BLACK |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:TPE Delta D Fender – 110mm x 95mm – 2 x 5m Pack