
Rubber & FoamSKU IP-TPEE-17.5X17-25M
Black TPE Expansion Joint Seal – 17.5mm x 17mm for 13–15mm Joints – 25m Coil
A black TPE expansion joint seal for 13 mm to 15 mm wide joints in concrete, screed and precast panels. Its flat top face has a central V-groove so the top can close up as the joint narrows, and three tiers of angled fins grip both joint walls. Inside, six hollow chambers let the section squeeze and recover as the structure moves. Free size 17.5 mm wide × 17 mm deep. Supplied as a continuous 25 m coil (£30.45 per metre inc VAT), held in stock in the UK.
At a glance
- Fits joints 13–15 mm wide: 17.5 mm across the fins, so it is always fitted under compression and held in by the fins, with no adhesive needed
- Flat top with V-groove: sits flush with the surface, and the groove lets the top fold in as the joint closes instead of bulging up
- Six hollow chambers (three each side of a central web) absorb movement and vibration
- TPV (PP-EPDM) thermoplastic rubber, 70–72 Shore A, working range −50 °C to +90 °C
- Good weathering, UV and abrasion resistance. Keeps water, grit and debris out of the joint
- Cuts cleanly with a sharp knife. 190 g per metre
Technical drawing

Specification
| Property | Value | Test method / source |
|---|---|---|
| Overall width (across the fins, free state) | 17.5 mm | Supplier drawing |
| Overall height (top face to base) | 17.0 mm | Supplier drawing |
| Joint / groove width it fits | 13 mm minimum – 15 mm maximum | Supplier data |
| Compression when fitted | ≈14–26 % across the width (17.5 mm into 15–13 mm) | Derived from the figures above |
| Joint depth needed | at least 17 mm, so the top sits flush | Derived from the 17 mm height |
| Cross-section | Flat top with central V-groove, central web, 3 tiers of fins each side, 6 hollow chambers, rounded base | Supplier drawing |
| Material | Thermoplastic elastomer, TPV type (PP-EPDM) | Supplier datasheet |
| Colour | Black | – |
| Hardness | 70–72 Shore A (product page 70°, datasheet 72°) | ISO 868 |
| Density (specific gravity) | 0.97 g/cm³ | ASTM D792 / ISO 1183 |
| Tensile strength | 7.4 MPa | ASTM D412 / ISO 37 |
| Elongation at break | 450 % | ASTM D412 / ISO 37 |
| Compression set, 22 h at 70 °C | 30 % | ASTM D395 B / ISO 815 |
| Compression set, 70 h at 125 °C | 41 % | ASTM D395 B / ISO 815 |
| Tear strength | Not published for this profile | – |
| Working temperature | −50 °C to +90 °C | Supplier datasheet |
| Weight | 190 g per metre (≈4.75 kg per 25 m coil) | Supplier data |
| Dimensional tolerance | ISO 3302-1:2014 class E2 (cross-section), L2 (length) | ISO 3302-1 |
| Supplied as | 25 m continuous coil | – |
| Price per metre | £30.45 inc VAT (£761.13 per 25 m coil) | – |
Materials and compliance
The seal is extruded from a TPV, a thermoplastic vulcanisate of polypropylene with cross-linked EPDM rubber. The EPDM gives the fins rubber-like recovery and resistance to weather and UV. The polypropylene keeps it light (SG 0.97), clean to cut and recyclable as a thermoplastic.
Approvals: the manufacturer does not state any approvals for this profile in its written specification, so we make no FDA, food-contact, WRAS, REACH or RoHS claim. If your project needs a declaration, ask us before ordering and we will request it.
How it fits

- Check the joint is 13–15 mm wide along its whole length and at least 17 mm deep.
- Brush and blow out dust, grit and loose concrete. The fins grip best on clean, sound joint walls.
- Start at one end with the flat, grooved face up. Squeeze the rounded base into the joint and press the seal down until the top is level with the surface. A wooden block or a rubber mallet helps.
- Work along the joint a short length at a time. Do not stretch the seal, or it will shrink back and open gaps at the ends.
- Cut to length with a sharp knife, leaving 1–2 mm extra so the ends butt tightly.

Where it is used
- Movement joints in multi-storey and underground car parks
- Joints between heavy concrete walls, precast panels and slabs
- Bridge decks and walkways with small joints
- Roofs, podiums and tunnels
- Water treatment plants, plant rooms and loading areas
Questions
What joint width does it fit?
Joints from 13 mm to 15 mm wide. Below 13 mm the section cannot squeeze in without bulging out of the top. Above 15 mm the fins do not press hard enough on the walls to hold it. Measure the narrowest and widest points of the joint before ordering.
Does it need adhesive?
No. The angled fins flex upwards as you push the seal in and dig into the joint walls if anything tries to pull it out. On joints with heavy traffic or standing water you can add a polyurethane or MS-polymer sealant bead along the edges for extra security.
Can vehicles drive over it?
Yes, when it is fitted flush in a joint within the 13–15 mm range. The flat top stays level with the surface, which is why this type of seal is used on car park decks. Tracked plant and steel-wheeled trolleys can damage any elastomer seal, so protect it during construction.
Is it suitable outdoors and in cold weather?
Yes. The TPV material is rated from −50 °C to +90 °C and resists weathering and UV, so it stays flexible through a UK winter and on sun-exposed decks.
How do I cut and join it?
Cut square with a sharp knife or a fine-toothed saw. Butt the ends tightly, leaving 1–2 mm extra so they press together. At corners, mitre the ends at 45°. For a permanent bond, TPV can be heat-welded or joined with a cyanoacrylate made for polyolefins (use a primer).
Is it watertight?
It keeps out water, dirt and debris in normal use, but it is a compression seal, not a hydrostatic waterstop. For joints under constant water pressure, use it as the visible top seal over a proper waterstop or sealant system.
How much movement can it take?
It works across the whole 13–15 mm range, so it takes about 2 mm of opening and closing between those limits. The six hollow chambers and the V-groove let it squeeze without bulging.
How is it supplied and how fast is dispatch?
As one continuous 25 m coil (about 4.75 kg). It is held in stock, and orders placed by the cut-off on our dispatch message ship the same day.
Need help choosing a profile for your joint? Call +44 1282 277786 or email sales@industrial-polymers.co.uk.
Related products
- Black TPE Expansion Joint Seal – 15.5mm x 13.2mm – 25m Coil (for 10–12.5 mm joints)
- Black TPE Expansion Joint Seal – 16mm x 18mm – 25m Coil (for 9–11 mm joints)
- Expansion Seal, Black TPE, 26mm x 26mm – 25m (for 19–23 mm joints)
Product details
| SKU | IP-TPEE-17.5X17-25M |
|---|---|
| Weight | 10.58 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Black TPE Expansion Joint Seal – 17.5mm x 17mm for 13–15mm Joints – 25m Coil