
Rubber & FoamSKU IP-TPEU-12X14X6-STD
TPE Square U Channel – 12mm x 14mm for 6mm Panels – 25m Coil
The heavy-duty member of our square U channel range for 6mm sheet. The profile is 12mm wide and 14mm high, with a 6mm parallel slot running 11mm deep, and every wall, including the base, is a full 3mm thick. That extra rubber gives a cushioned, knock-absorbing edge on guards, glass and boards that take regular impacts, and the long 11mm arms grip a wide band of each face, so the trim stays put without glue in most uses. It is extruded from black 60 Shore A thermoplastic elastomer (TPE), supplied as one continuous 25m coil and held in UK stock.

At a glance
- Fits sheet, glass and panel edges 6mm thick
- 12mm wide x 14mm high, 6mm slot 11mm deep
- Uniform 3mm walls and base: the thickest, most impact-absorbing 6mm trim we stock
- 11mm gripping arms hold each face, so adhesive is rarely needed
- Flat, square 12mm top for a bold, tidy finished edge
- 60 Shore A TPE: resists UV, weathering, chemicals and repeated flexing; -40°C to +90°C
- Cuts cleanly with a sharp knife; 100% recyclable thermoplastic
- Black, 25m coil: about £16.68 per metre inc VAT (£13.90 ex VAT)
Typical uses
- Capping the cut edges of 6mm sheet-metal, polycarbonate and acrylic machine guards
- Edge protection on 6mm toughened glass screens, partitions and glazing panels
- Vending machine, kiosk and display cabinet panels
- Running boards, steps and stair-edge panels
- Furniture, shelving and shopfitting boards
- Protecting 6mm sheet stock during handling and transport

Which size do I need?
Measure the thickness of the edge and match it to the slot. A square U channel should be a snug push fit: on a thinner panel it sits loose, on a thicker one it splays the arms. Several of our trims fit 6mm sheet; they differ in face size and wall weight.
| Profile | Fits panel | Wall | Choose it when |
| 9mm x 11.5mm | 6mm | 1.5mm | you want the slimmest face |
| 10mm x 10mm | 6mm | 2mm | you want a compact, even square look |
| 12mm x 14mm (this item) | 6mm | 3mm | the edge takes knocks and you want maximum cushioning and grip |
| 11mm x 12mm | 6.5–7mm | – | the panel is slightly thicker than 6mm |
| 12mm x 12mm | 8mm | 2mm | the panel is 8mm thick |
Specification
| Property | Value | Standard / source |
| Profile | Square U channel (parallel-sided slot, flat top) | Manufacturer product data |
| Overall width | 12.0 mm | Manufacturer product data |
| Overall height | 14.0 mm | Manufacturer product data |
| Wall thickness | 3.0 mm, uniform (constant section) | Manufacturer product data |
| Slot depth (gripping arm length) | 11.0 mm | Manufacturer product data |
| Slot width | 6.0 mm (12mm width less two 3mm walls) | Derived from manufacturer dimensions |
| Base thickness (above slot) | 3.0 mm (14mm height less 11mm arms) | Derived from manufacturer dimensions |
| Panel / edge thickness it fits | 6 mm | Manufacturer product data |
| Cross-section area | approx. 102 mm² | Calculated from the nominal dimensions |
| Material | Thermoplastic elastomer (TPE), 100% recyclable | Manufacturer product data |
| Hardness | 60 Shore A | Manufacturer product data (Shore A durometer) |
| Operating temperature | -40°C to +90°C | Manufacturer product data |
| Dimensional tolerance | ISO 3302-1 class E2 (cross-section), L2 (length) | ISO 3302-1 |
| Resistance | Excellent weathering, UV and chemical resistance; good tear and abrasion resistance; excellent flex-fatigue resistance | Manufacturer product data (qualitative) |
| Density, tensile strength, elongation, tear strength, compression set | Not published by the manufacturer for this profile – ask us if you need a figure for a specification | – |
| Colour | Black | – |
| Supplied as | One continuous 25m coil | – |
| Part number | IP-TPEU-12X14X6-STD | – |
Materials and compliance
This channel is a thermoplastic elastomer: it behaves like a soft rubber in use but can be melted and re-processed, so offcuts and old trim are 100% recyclable. The manufacturer does not state any food-contact (FDA, EC 1935/2004), WRAS, fire-rating, REACH or RoHS approval for this profile, so we do not claim one. If your application needs a certified material, call us and we will suggest a suitable alternative.
How much do I need?
Total the length of every exposed edge, add about 5% for corners and offcuts, then divide by 25 and round up. Example: a run of guarding with 55m of edge needs 55m + 5% ≈ 58m, so three 25m coils.
Fitting tips
- Check the panel is 6mm; the slot is sized for a firm push fit at that thickness.
- Start at one end and push the channel on by hand, working along the edge until the 11mm arms sit flat against both faces. A rubber mallet helps on long runs.
- Cut square with a sharp trimming knife, or a fine-toothed saw for very clean ends.
- On corners, either bend the channel round a radius or cut 45° mitres for a sharp square corner.
- For high-vibration or overhead edges, run a thin bead of flexible adhesive inside the slot.
Frequently asked questions
What panel thickness does it fit?
It is made for 6mm panels and sheets. The slot is 6mm wide and 11mm deep. For 8mm panels choose the 12mm x 12mm channel; for 6.5–7mm, the 11mm x 12mm.
How is it different from the other 6mm square U channels?
It has the thickest walls (3mm) and the longest arms (11mm), so it gives the most cushioning and the strongest grip. Choose the 10mm x 10mm or 9mm x 11.5mm if you want a slimmer edge.
Do I need glue to fit it?
Usually not. The 11mm arms grip a wide band of each face, so a push fit holds on most guards, screens and boards. Add a thin bead of flexible adhesive where there is heavy vibration or the edge is overhead.
Can I use it outdoors?
Yes. TPE has excellent weathering and UV resistance and stays flexible from -40°C to +90°C, so it suits outdoor panels, trailers and covered walkways as well as indoor machinery.
How do I cut and join it?
Cut it with a sharp knife or a fine-toothed saw. Butt ends together squarely, or cut 45° mitres at corners. Because it is a thermoplastic, ends can also be heat-welded with the right equipment; for most jobs a tight butt joint is enough.
Will it go round corners?
The rigid square section is designed to resist bending and warping, so for tight square corners cut a mitre. On gentle curves and large radii it can be bent round in one piece.
Is it food-safe or fire-rated?
No food-contact or fire rating is stated for this profile. Contact us if you need a certified material.
Can I order a shorter length?
This item is sold as a full 25m coil. Call +44 1282 277786 or email sales@industrial-polymers.co.uk if you need a different quantity.
Not sure which profile suits your panel? Contact our team with the panel thickness and what it is used for, and we will point you to the right channel.
Product details
| SKU | IP-TPEU-12X14X6-STD |
|---|---|
| Weight | 6.61 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:TPE Square U Channel – 12mm x 14mm for 6mm Panels – 25m Coil