
Rubber & FoamSKU IP-TPEU-8X11-STD
TPE Square U Channel Edge Trim – 8mm x 11mm for 4mm Panels – 50m Coil
A square-section push-on trim for capping the raw edges of 4mm sheet. The profile is 8mm wide at the base and 11mm tall, with a 4mm slot running 9mm deep. The slot is tapered: it narrows towards the mouth, so the two arms spring apart as you push the trim on and then clamp both faces of the panel. That gives a firm grip without adhesive, and the trim can be pulled off and reused. The 2mm walls and 2mm base keep it square and hard to crush. It is extruded from black 60 Shore A thermoplastic elastomer (TPE), supplied as one continuous 50m coil, and held in stock.

At a glance
- Fits sheet and panel edges 4mm thick
- 8mm wide x 11mm high, 4mm slot 9mm deep
- Tapered slot clamps the panel: no glue needed, removable and reusable
- 2mm walls and base: square, impact-absorbing and hard to crush
- 60 Shore A TPE: resists UV, weathering, chemicals and repeated flexing
- Cuts cleanly with a knife; fully recyclable thermoplastic
- Black, 50m coil, about £10.06 per metre
Typical uses
- Capping sharp edges on 4mm sheet-metal machine guards, covers and enclosure panels
- Edge finish on 4mm glass, acrylic and polycarbonate panels and glazing contours
- Vending machine, kiosk and cabinet panels
- Furniture, shelving and stair-edge panels made from 4mm board or sheet
- Running boards and light vehicle or trailer panels
- Protecting sheet stock edges during handling and transport
Which size do I need?
Measure the edge you want to cover and match it to the slot. For 4mm edges, and the sizes either side:
| U channel | Fits edge thickness | Choose it when |
|---|---|---|
| TPE Square U Channel 8mm x 11mm (this one) | 4mm | You want a gripping tapered slot and a 50m coil at the lowest cost per metre |
| TPE Square U Channel 8mm x 12mm | 4mm | You want a slightly taller profile on a shorter 25m coil |
| TPE Square U Channel 12mm x 16mm | 4mm | You want a much heavier, deeper trim |
| TPE Square U Channel 7mm x 12mm | 3mm | Your sheet is 3mm thick |
| TPE Square U Channel 9mm x 16mm | 5mm | Your sheet is 5mm thick |
Specification
| Property | Value | Test method / source |
|---|---|---|
| Profile and dimensions | ||
| Profile | Square-section U channel with tapered slot (push-on edge trim) | – |
| Overall width | 8.0 mm (at base; sides taper inwards towards the top) | Nominal, ISO 3302-1 class E2 |
| Overall height | 11.0 mm | Nominal, ISO 3302-1 class E2 |
| Slot width | 4.0 mm at the base, narrowing towards the mouth | Nominal |
| Slot depth (gripping arm length) | 9.0 mm | Nominal |
| Wall thickness | 2.0 mm | Nominal |
| Base thickness under slot | 2.0 mm | Nominal |
| Fits edge / panel (clamping range) | 4 mm to 4 mm | Manufacturer datasheet |
| Dimensional tolerance | Cross-section class E2, length class L2 (quality level 2) | ISO 3302-1 |
| Weight | 135 g per metre as stated on the manufacturer datasheet (approx. 6.8 kg per 50 m coil) | Manufacturer datasheet |
| Material | ||
| Material | Thermoplastic elastomer (TPE) | – |
| Hardness | 60 Shore A | Shore A durometer (ISO 48-4) |
| Working temperature | -25 °C to +70 °C | Manufacturer datasheet (a wider -40 °C to +90 °C is quoted elsewhere; we list the datasheet figure) |
| Environmental resistance | UV, weathering, chemicals, flex fatigue; good tear and abrasion resistance | Manufacturer data |
| Density, tensile strength, elongation, tear, compression set | Not published for this profile; ask us if you need them | – |
| Supply | ||
| Colour | Black | – |
| Unit of sale | One continuous 50 m coil | – |
| Availability | Held in stock | – |
Material and compliance
TPE is a rubber-like material that is processed like a plastic. It gives a consistent, rubbery feel, needs no vulcanising, and can be recycled at end of life.
- Weathering: stable in sunlight and outdoor conditions, and resists ageing
- Chemical resistance: stands up to water, mild cleaning agents and general workshop exposure
- Flex life: recovers its shape after long periods compressed or stretched, so the grip lasts and the trim can be refitted
- Tolerances: extruded to ISO 3302-1, the standard tolerance scheme for rubber and elastomer extrusions
No food-contact, potable-water (WRAS), REACH/RoHS or fire-rating approval is claimed for this profile. If you need a declaration for your file, contact our team.
How much do I need?
Total the length of every edge you want to cover and add about 5% for trimming. Example: twenty access panels, each 1m x 0.6m, have 64m of perimeter, or about 67m with allowance, so you need two 50m coils. Fifteen of the same panels (about 50m with allowance) fit on one coil.
Fitting tips
- Check the panel really is 4mm: thinner sheet will not be clamped, thicker sheet will over-splay the arms
- Deburr the edge and wipe it free of oil and grease before fitting; both improve the grip
- Start at one end and press the channel on with your thumb as you work along; a soft mallet helps on long runs
- Cut slightly over length with a sharp knife and push the ends together for a tight joint
- Ease it round gentle curves; on a tight corner, cut a V-notch in the base or butt two lengths
- For a permanent or vibration-proof fit, add a thin bead of sealant or adhesive in the slot
Questions
What edge thickness does it fit?
It is made for 4mm edges. On 3mm sheet choose the 7mm x 12mm square U channel; on 5mm sheet choose the 9mm x 16mm.
Why is the slot tapered?
The slot is 4mm at the base and narrower at the mouth. Pushing the trim onto a 4mm panel spreads the arms, and they press back on both faces. That is what holds it in place without glue.
How does it differ from the 8mm x 12mm version?
Both fit 4mm edges. This one is 11mm tall with a tapered, gripping slot and comes on a 50m coil, so it costs less per metre. The 8mm x 12mm is slightly taller and comes on a 25m coil.
Does it need glue? Can I remove it?
Not usually. The tapered arms grip a clean 4mm edge on their own, and the trim can be pulled off and refitted. Add adhesive only where there is heavy vibration or you want it permanent.
Can it go round curves and corners?
Yes, it follows gentle curves. For a tight 90° corner, notch the base or join two lengths at the corner.
Is it suitable outdoors, and what temperatures can it take?
Yes. TPE resists UV and weathering. The datasheet working range is -25°C to +70°C, so keep it away from ovens, exhausts and other hot surfaces.
How do I cut and join it?
A sharp knife or snips gives a clean square cut. Butt the ends tightly; for a sealed joint, add a dab of instant adhesive.
What is it made of, and is it food-safe?
Black 60 Shore A thermoplastic elastomer (TPE). No food-contact approval is claimed for this trim.
How accurate are the dimensions?
The cross-section is extruded to ISO 3302-1 class E2, so allow a few tenths of a millimetre either way on the nominal sizes.
When will it ship? Can I buy a shorter length?
This trim is held in stock and ships in line with the dispatch times shown on this page. This listing is a full 50m coil in black; for cut lengths or larger quantities, ask our team for a quote.
Need help choosing an edge trim? Contact our team on +44 1282 277786 or sales@industrial-polymers.co.uk.
Product details
| SKU | IP-TPEU-8X11-STD |
|---|---|
| Weight | 15.43 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:TPE Square U Channel Edge Trim – 8mm x 11mm for 4mm Panels – 50m Coil