
Rubber & FoamSKU IP-TPEUC-7X12X3-STD
TPE Square U Channel – 7mm x 12mm for 3mm Panels – 25m Coil
A compact, square-section push-on trim for capping the raw edges of 3mm sheet. The profile is 7mm wide and 12mm tall, with a 3mm parallel slot running 10mm deep. Both walls and the base are a full 2mm thick, so the trim stays square, takes knocks without crushing, and the tall sides cover 10mm of each face of the panel. That deep grip holds a clean 3mm edge firmly without adhesive. It is extruded from black 60 Shore A thermoplastic elastomer (TPE), supplied as one continuous 25m coil, and held in stock.

At a glance
- Fits sheet and panel edges 3mm thick
- 7mm wide x 12mm high, 3mm slot 10mm deep
- Uniform 2mm walls and base: rigid, impact-absorbing and hard to crush
- 10mm gripping arms hold a wide strip of each face, so glue is rarely needed
- 60 Shore A TPE: resists UV, weathering, chemicals and repeated flexing
- Cuts cleanly with a knife; fully recyclable thermoplastic
- Black, 25m coil, about £17.22 per metre
Typical uses
- Capping sharp edges on 3mm sheet-metal machine guards, covers and enclosure panels
- Edge finish on 3mm glass, acrylic and polycarbonate panels and glazing contours
- Vending machine, kiosk and cabinet panels
- Furniture, shelving and stair-edge panels made from 3mm board or sheet
- Running boards and light vehicle or trailer panels
- Protecting sheet stock edges during handling and transport
Which size do I need?
Measure the edge you want to cover and match it to the slot. For 3mm edges there are several square TPE options:
| U channel | Fits edge thickness | Choose it when |
|---|---|---|
| TPE Square U Channel 7mm x 12mm (this one) | 3mm | You want a slim, neat trim with a 10mm grip |
| TPE Square U Channel 7mm x 18mm | 3mm | You want a much deeper grip on the panel faces |
| TPE Square U Channel 9mm x 17mm | 3mm | You want thicker walls and a 50m coil |
| TPE Square U Channel 6mm x 12mm | 2mm | Your sheet is 2mm thick |
| TPE Square U Channel 8mm x 12mm | 4mm | Your sheet is 4mm thick |
Specification
| Property | Value | Test method / source |
|---|---|---|
| Profile and dimensions | ||
| Profile | Square-section U channel (push-on edge trim) | – |
| Overall width | 7.0 mm | Nominal, ISO 3302-1 class E2 |
| Overall height | 12.0 mm | Nominal, ISO 3302-1 class E2 |
| Slot width | 3.0 mm, parallel sides | Nominal |
| Slot depth (gripping arm length) | 10.0 mm | Nominal |
| Wall thickness | 2.0 mm each side | Nominal |
| Base thickness under slot | 2.0 mm | Nominal |
| Fits edge / panel (clamping range) | 3 mm only | Manufacturer data |
| Dimensional tolerance | Cross-section class E2, length class L2 (quality level 2) | ISO 3302-1 |
| Weight | 55 g per metre, approx. 1.4 kg per 25 m coil | Manufacturer data |
| Material | ||
| Material | Thermoplastic elastomer (TPE) | – |
| Hardness | 60 Shore A | Shore A durometer (ISO 48-4) |
| Working temperature | -25 °C to +70 °C | Manufacturer datasheet (a wider -40 °C to +90 °C is quoted elsewhere; we list the datasheet figure) |
| Environmental resistance | UV, weathering, chemicals, flex fatigue; good tear and abrasion resistance | Manufacturer data |
| Density, tensile strength, elongation, tear, compression set | Not published for this profile; ask us if you need them | – |
| Supply | ||
| Colour | Black | – |
| Unit of sale | One continuous 25 m coil | – |
| Availability | Held in stock | – |
Material and compliance
TPE is a rubber-like material that is processed like a plastic. It gives a consistent, rubbery feel, needs no vulcanising, and can be recycled at end of life.
- Weathering: stable in sunlight and outdoor conditions, and resists ageing
- Chemical resistance: stands up to water, mild cleaning agents and general workshop exposure
- Tolerances: extruded to ISO 3302-1, the standard tolerance scheme for rubber and elastomer extrusions
No food-contact, potable-water (WRAS), REACH/RoHS or fire-rating approval is claimed for this profile. If you need a declaration for your file, contact our team.
How much do I need?
Total the length of every edge you want to cover and add about 5% for trimming. Example: eight access panels, each 1m x 0.6m, have 25.6m of perimeter, or about 27m with allowance, so you need two 25m coils. Four of the same panels (about 13.5m with allowance) fit on one coil.
Fitting tips
- Check the panel really is 3mm: thinner sheet will sit loose, thicker sheet will splay the walls
- Deburr the edge and wipe it free of oil and grease before fitting
- Start at one end and press the channel on with your thumb as you work along; a soft mallet helps on long runs
- Cut slightly over length with a sharp knife and push the ends together for a tight joint
- Ease it round gentle curves; on a tight corner, cut a V-notch in the base or butt two lengths
- For a permanent or vibration-proof fit, add a thin bead of sealant or adhesive in the slot
Questions
What edge thickness does it fit?
It is made for 3mm edges only. On 2mm sheet choose the 6mm x 12mm square U channel; on 4mm sheet choose the 8mm x 12mm.
How does it differ from the 7mm x 18mm version?
Both fit 3mm edges. This one is 12mm tall with 10mm arms, for a neat, low-profile finish. The 7mm x 18mm has much taller sides and grips more of each face.
Does it need glue?
Not usually. The 10mm sides grip a clean 3mm edge firmly on their own. Add adhesive only where there is heavy vibration or you want it permanent.
Can it go round curves and corners?
Yes, it follows gentle curves. For a tight 90° corner, notch the base or join two lengths at the corner.
Is it suitable outdoors, and what temperatures can it take?
Yes. TPE resists UV and weathering. The datasheet working range is -25°C to +70°C, so keep it away from ovens, exhausts and other hot surfaces.
How do I cut and join it?
A sharp knife or snips gives a clean square cut. Butt the ends tightly; for a sealed joint, add a dab of instant adhesive.
What is it made of, and is it food-safe?
Black 60 Shore A thermoplastic elastomer (TPE). No food-contact approval is claimed for this trim.
How accurate are the dimensions?
The cross-section is extruded to ISO 3302-1 class E2, so allow a few tenths of a millimetre either way on the nominal sizes.
When will it ship?
This trim is held in stock and ships in line with the dispatch times shown on this page.
Can I buy a shorter length?
This listing is a full 25m coil in black. For cut lengths or larger quantities, ask our team for a quote.
Need help choosing an edge trim? Contact our team on +44 1282 277786 or sales@industrial-polymers.co.uk.
Product details
| SKU | IP-TPEUC-7X12X3-STD |
|---|---|
| Weight | 3.31 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:TPE Square U Channel – 7mm x 12mm for 3mm Panels – 25m Coil