
Rubber & FoamSKU IP-TPEUC-9X13X1-BLACK
TPE U Channel Edge Trim – 9mm x 13mm for 1mm to 2.5mm Panels – 100m Coil
A push-on TPE U channel edge trim, 9mm wide and 13mm high, for panels 1mm to 2.5mm thick. Two pairs of angled internal ridges bite onto the panel so it stays put without adhesive, and a 3.5mm solid round base takes the knocks that would otherwise chip paint, crack glass or cut a hand. Sold as a continuous 100m coil in black or white, held in UK stock.
At a glance
- 9mm x 13mm TPE U channel, black or white, 100m coil (£7.61 per metre)
- Grips 1mm to 2.5mm panels: sheet steel, aluminium, glass, acrylic, board
- Measured grip of 17 N, 25 N and 52 N per 10cm on 1mm, 1.5mm and 2.5mm panels
- Firm 90 Shore A clamp body; 3.5mm round base absorbs impact
- Rated −25°C to +70°C; weather, UV and chemical resistant
- No glue: press on by hand, pull off and reuse; cuts with a knife
Technical drawing

Nominal dimensions in mm. The internal ridges are shown for shape and are not dimensioned. Download or print the drawing from the product gallery.
Specifications
| Property | Value | Method / source |
|---|---|---|
| Overall width | 9mm (across the round base) | Manufacturer's drawing U8-01 |
| Overall height | 13mm | Manufacturer's drawing U8-01 |
| Solid base thickness | 3.5mm (thickest point) | Manufacturer's drawing and technical data |
| Open depth (grip length) | 9.5mm | Manufacturer's drawing U8-01 |
| Panel thickness it fits | 1mm to 2.5mm (recommended) | Manufacturer's product data; datasheet lists 0.5mm to 2.5mm edge thickness, with grip only measured from 1mm |
| Grip on 1mm panel | 17 N per 10cm | Manufacturer's pull-off test at 20°C |
| Grip on 1.5mm panel | 25 N per 10cm | Manufacturer's pull-off test at 20°C |
| Grip on 2.5mm panel | 52 N per 10cm | Manufacturer's pull-off test at 20°C |
| Material | Thermoplastic elastomer (TPE) | Manufacturer's datasheet RC930 |
| Hardness, clamp body | 90 Shore A | Shore A durometer (manufacturer's datasheet) |
| Hardness, gripping lips | 60 Shore A | Manufacturer's product page; the datasheet lists a single 90 Shore A material |
| Working temperature | −25°C to +70°C | Manufacturer's datasheet |
| Dimensional tolerance | ISO 3302-1 class E2 (cross-section), L2 (length); datasheet: quality level 2 | ISO 3302-1 |
| Density | Not published for this profile | – |
| Tensile strength / elongation | Not published for this profile | – |
| Tear strength / compression set | Not published for this profile | – |
| Colours | Black, white | – |
| Supplied as | One continuous 100m coil | – |
Need a density, tensile or compression-set figure for a specification? Ask our team and we will tell you what can be supplied for this profile.
Materials and compliance
The trim is extruded from a thermoplastic elastomer (TPE): a rubber-like material that flexes and recovers its shape without vulcanising, so it is fully recyclable. The manufacturer states it has excellent weathering, UV, flex-fatigue and chemical resistance, with good tear and abrasion resistance.
The manufacturer does not state any food-contact, WRAS, REACH, RoHS or fire approval for this exact product, so we make no such claim. If your job needs a certificate, contact us before ordering.
Typical uses
- Covering sharp cut edges on sheet-metal guards, enclosures and cabinets
- Finishing glass and acrylic panel edges in displays, shelving and vending machines
- Protecting panel edges on running boards, steps, stair nosings and furniture
- Protecting goods and panels in transit, then removing the trim for reuse
Which edge trim do I need?
| Edge trim | Size | Panel thickness | Coil |
|---|---|---|---|
| TPE U channel 8.5 x 12mm | 8.5mm x 12mm | 1mm to 3mm | 100m |
| TPE U channel 8 x 13mm | 8mm x 13mm | 2mm | 50m |
| TPE U channel 9 x 13mm (this item) | 9mm x 13mm, 3.5mm base | 1mm to 2.5mm | 100m, black or white |
Choose the trim whose clamping range covers your panel thickness. The 9 x 13mm profile has the thickest base of these, for edges that take more knocks.
How much do I need?
Add up every edge you want to cover and divide by 100. Example: 40 cabinet doors with 2.4m of exposed edge each need 96m, so one coil covers the job with spare for trimming.
Fitting tips
- Deburr the edge and wipe it with a grease remover first; the manufacturer recommends both for the best grip.
- Start at a corner and press the channel on by hand, working along the edge. Tap it home with a rubber mallet if needed.
- Cut square with a sharp knife, side cutters or a fine-tooth saw.
- On tight bends, cut a small notch in the inside of the curve so the trim lies flat.
Frequently asked questions
Do I need glue to fit this edge trim?
No. The internal ridges clamp the panel and hold it without adhesive, so you can remove the trim and fit it again.
What panel thickness does it fit?
It is designed for 1mm to 2.5mm. Grip increases with thickness: 17 N per 10cm on 1mm, 25 N on 1.5mm and 52 N on 2.5mm. For thinner or thicker panels, choose another trim from the table above.
How do I measure my panel?
Measure the panel thickness with a caliper, including any paint or film, at the edge you are trimming. If it is between 1mm and 2.5mm, this trim fits.
Can it be used outdoors?
Yes. TPE resists weather, UV and many chemicals, and the trim is rated from −25°C to +70°C.
Will it go round corners and curves?
Yes. TPE flexes well and resists bending fatigue, so it follows gentle curves. Cut a small notch in the inside of tight corners so it does not ripple.
How do I cut and join it?
Cut it with a sharp knife or side cutters for a clean, square end. For a continuous run, butt the two cut ends together tightly on the panel; because the trim clamps the edge, the joint stays closed without bonding. Start and finish runs at a corner or on a hidden edge for the neatest result.
Is it safe for food areas or drinking water?
No food-contact or WRAS approval is stated for this product. Ask us for a certified alternative if you need one.
Are black and white the same price?
Yes. Both colours are £760.74 inc VAT per 100m coil.
Need a different panel range or colour? Contact our team on +44 1282 277786 and we will help you choose an edge trim.
Product details
| SKU | IP-TPEUC-9X13X1-BLACK |
|---|---|
| Weight | 16.53 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:TPE U Channel Edge Trim – 9mm x 13mm for 1mm to 2.5mm Panels – 100m Coil