
Rubber & FoamSKU IP-TPEU-4.5X12X1.5-STD
TPE U Channel – 4.5mm x 12mm Deep Grip for 1.5mm Edges – 50m Coil
A slim black TPE U channel with extra-deep arms for capping the raw edges of 1.5mm sheet: steel and aluminium panels, cabinet and enclosure sides, vending and kiosk panels, furniture, stair and running-board edges, and thin glazing. It is only 4.5mm across, so it finishes an edge neatly, but its two parallel arms run 10.5mm down each face of the sheet. That long grip holds far more securely than a short trim and often means no adhesive is needed. The round 1.5mm base cushions knocks to the edge. Made from 60 Shore A thermoplastic elastomer, firm enough to hold its shape, and supplied as one continuous 50m coil.

At a glance
- Fits sheet and panels 1.5mm thick
- 4.5mm wide x 12mm high, 1.5mm slot 10.5mm deep, 1.5mm walls and base
- Deep 10.5mm grip on each face for a secure push fit
- Round-bottom profile with square-cut parallel arms
- Thermoplastic elastomer (TPE), 60 Shore A: firm, holds its shape under knocks
- Temperature range -40°C to +90°C
- Resists weathering, UV, chemicals, flex fatigue, tearing and abrasion
- Cuts cleanly with a sharp knife; 100% recyclable thermoplastic
- 50m coil in black, about £8.94 per metre
Typical uses
- Capping sharp cut edges of 1.5mm sheet-metal panels, guards and enclosure covers
- Edge finishing on vending machines, kiosks, cabinets and shop-fitting panels
- Protecting the edges of thin glazing and acrylic in frames and displays
- Bumper edging on furniture, running boards and stair panels
- Protecting sheets, and the people handling them, during storage and transport
- Edges that get knocked or handled often, where a short-armed trim would work loose

Which size do I need?
Measure the thickness of the edge you are covering and choose the channel whose slot matches it. For 1.5mm sheet, choose this deep-grip version for a firmer hold, or the 4.5mm x 8mm when you want the shortest profile.
| U channel | Material | Fits edge thickness | Size (W x H) | Grip depth |
|---|---|---|---|---|
| TPE U Channel 3mm x 7mm | TPE, black | 1mm | 3 x 7mm | – |
| TPE U Channel 4.5mm x 8mm | TPE, black | 1.5mm | 4.5 x 8mm | 6.5mm |
| TPE U Channel 4.5mm x 12mm (this one) | TPE, black | 1.5mm | 4.5 x 12mm | 10.5mm |
| TPE U Channel 4mm x 23mm | TPE, black | 2mm (deep grip) | 4 x 23mm | – |
| TPE U Channel 8.5mm x 12mm | TPE | 1mm to 3mm | 8.5 x 12mm | – |
Specification
| Property | Value | Test method / basis |
|---|---|---|
| Profile and dimensions | ||
| Profile | Round-bottom U channel with square-cut parallel arms (push-on edge trim) | Manufacturer's profile drawing |
| Overall width | 4.5 mm | Nominal |
| Overall height | 12 mm | Nominal |
| Slot (channel) width | 1.5 mm | Nominal |
| Slot (channel) depth / grip on each face | 10.5 mm | Nominal |
| Wall thickness | 1.5 mm each side | Nominal (manufacturer's stated thickness) |
| Base thickness | 1.5 mm | Nominal (12 mm height less 10.5 mm channel depth) |
| Fits panel / edge (clamping range) | 1.5 mm only | Manufacturer's clamping range |
| Dimensional tolerance | Class E2 (cross-section), L2 (length) | ISO 3302-1 |
| Material properties | ||
| Material | Thermoplastic elastomer (TPE) | – |
| Hardness | 60 Shore A | Shore A durometer (ISO 48-4) |
| Minimum temperature | -40 °C | Manufacturer's rating |
| Maximum temperature | +90 °C | Manufacturer's rating |
| Resistance | Weathering, UV, general chemicals, ageing, flex fatigue, tear, abrasion | Manufacturer's description (qualitative) |
| Density, tensile strength, elongation, tear strength, compression set | Not published for this profile | Ask us if your specification needs them |
| Supply | ||
| Colour | Black | – |
| Unit of sale | One continuous 50 m coil | – |
| Part number | IP-TPEU-4.5X12X1.5-STD | – |
Material and compliance
This channel is extruded from a thermoplastic elastomer (TPE): a rubber-like material that flexes and recovers like rubber but, unlike vulcanised rubber, can be melted down and recycled. At 60 Shore A it is firm enough to resist compression and keep its shape on edges that take regular knocks.
- Dimensional tolerances: extruded to ISO 3302-1, cross-section class E2 and length class L2.
- Recyclable: the manufacturer states the material is 100% recyclable.
- No product approvals are stated for this profile: it is not offered as food-contact, drinking-water (WRAS) or fire-rated material. Ask us if you need an approved alternative.
How much do I need?
Add up every edge you want to cover and allow around 5% for trimming and joints. Example: twenty 1.5mm cabinet side panels, each with two exposed 1.2m edges, need 48m, or about 50m with allowance. That is one 50m coil.
Fitting tips
- Deburr the edge and wipe it with a degreaser first: the arms grip better on a clean edge
- Start at one end, set the open side of the channel on the edge and press it home with your thumb as you go; a rubber mallet helps on long runs
- Check the sheet reaches the bottom of the slot so the full 10.5mm of each arm is gripping
- Cut slightly over length with a sharp knife and push the ends together for a tight butt joint
Questions
Will it stay on without glue?
On a clean, deburred 1.5mm edge it is a firm push fit, and the 10.5mm arms give it a much larger grip area than a short trim. For edges that are knocked very often, or for a permanent fit, run a thin bead of flexible adhesive in the slot.
Will it fit 1mm or 2mm sheet?
It is made for 1.5mm only. On 1mm sheet it will be loose unless glued; use the TPE U channel 3mm x 7mm instead. 2mm sheet will force the arms apart; use the 4mm x 23mm TPE channel.
What is the difference from the 4.5mm x 8mm channel?
Both fit 1.5mm sheet and are 4.5mm wide. This one is 12mm tall with 10.5mm arms, so it grips further down the sheet and holds more firmly. The 8mm version is lower-profile and comes on a 100m coil.
Can it go round corners and curves?
It follows gentle curves. For a sharp 90° corner, mitre the ends and butt two lengths together, or cut a small V-notch out of the arms so the base can bend.
What temperatures can it take?
It is rated from -40°C to +90°C. Keep it away from hot surfaces such as heaters, ovens or exhausts that run hotter than that; for those, choose a silicone channel.
Is it suitable for outdoor use?
Yes. TPE resists weathering, UV and ageing, so it can be used on outdoor panels, steps and running boards.
How do I cut and join it?
Cut square with a sharp knife or fine shears. Join lengths with a tight butt joint; a drop of flexible adhesive at the joint stops it opening up.
Can I use it on food equipment?
No food-contact approval is stated for this profile, so we do not recommend it where it may touch food. Ask us for an approved silicone channel.
Can I buy a shorter length or other colours?
This listing is a full 50m coil in black. For cut lengths or larger quantities, ask our team for a quote.
Need help choosing an edge trim or a seal? Contact our team.
Product details
| SKU | IP-TPEU-4.5X12X1.5-STD |
|---|---|
| Weight | 5.51 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:TPE U Channel – 4.5mm x 12mm Deep Grip for 1.5mm Edges – 50m Coil