
Rubber & FoamSKU IP-HSEA-50X30-10
Watertight Hatch Seal – 50mm x 30mm – 10m or 20m Strip
Price shown updates with the option you pick.
This watertight hatch seal 50mm x 30mm is a composite EPDM marine seal for hatches, cargo covers and access doors: a closed-cell sponge core gives the compression needed to stop water, while a tough solid rubber skin takes the wear of repeated opening and closing. It is sold as one continuous strip, 10m or 20m long.
At a glance
- Hatch seal 50mm wide x 30mm high with chamfered sealing corners
- Composite marine door seal: solid EPDM skin over a closed-cell EPDM sponge core
- Sponge core compresses easily for a low closing force and a watertight joint
- EPDM resists ozone, UV and weathering
- Works from -40°C to +120°C
- Supplied as one length of 10m or 20m, so most hatches can be sealed without a joint
Typical uses
- Watertight hatches and cargo hatch covers on work boats, ferries and ships
- Weathertight access doors and inspection covers on deck
- Skylights and ullage plugs
- Hatch covers on oil, gas and chemical tankers
- Weatherproof doors on offshore and dockside equipment enclosures
Which one do I need?
| Seal size | Best for |
|---|---|
| 40mm x 20mm | Smaller hatches and lockers with a shallow retaining channel |
| 50mm x 30mm (this seal) | Medium hatches, cargo covers and doors with a 50mm channel and moderate closing gap |
| 57mm x 32mm | Larger hatches and doors needing a wider seal face |
| 70mm x 40mm | Heavy cargo hatch covers with a deep channel and a large compression gap |
Technical drawing
Specification
| Profile | Rectangular with chamfered sealing face |
| Size | 50mm wide x 30mm high |
| Outer skin | Solid EPDM rubber, 67° Shore A |
| Core | Closed-cell EPDM sponge |
| Skin tensile strength | 7.72 MPa |
| Sponge tensile strength | 2.8 MPa |
| Skin elongation at break | 360% |
| Sponge elongation at break | 140% |
| Skin compression set | 25% (22 h at 70°C) |
| Sponge compression deflection | 12.1 kPa |
| Temperature range | -40°C to +120°C |
| Colour | Black |
| Unit of sale | One strip, 10m or 20m |
How much do I need?
Measure the full perimeter of the hatch channel and add about 10% for trimming and the joint. Example: a 900mm x 700mm hatch has a perimeter of 2 x (0.9 + 0.7) = 3.2m; with 10% that is about 3.5m, so a 10m strip seals two hatches of that size with spare. A 1.5m x 2m cargo cover needs about 7.7m, so one 10m strip covers it; for two such covers choose the 20m strip.
Fitting tips
- Clean the retaining channel of old seal, adhesive and rust before fitting the new seal.
- Fit the seal with the chamfered face towards the knife edge or coaming so it closes evenly.
- Lay the seal into the channel without stretching it; a stretched seal shrinks back and opens gaps at the corners.
- Start the joint away from a corner and cut both ends square with a sharp blade for a tight butt joint; bond it with a suitable rubber adhesive.
- Check the closed hatch with a chalk line or water test and adjust the dogs for even compression.
Complete your project
- Watertight Hatch Seal – 40mm x 20mm
- Watertight Hatch Seal – 57mm x 32mm – 10m Length
- Watertight Hatch Seal – 70mm x 40mm – 10m Length
Questions
What size channel does the 50mm x 30mm hatch seal fit?
It is 50mm wide and 30mm high, so it suits retaining channels around 50mm wide. Measure your existing seal or channel before ordering.
Why does the marine door seal have two materials?
The closed-cell sponge core compresses to form the watertight barrier, while the solid EPDM skin protects the core from wear, tearing and weathering.
Is the sponge core waterproof?
Yes. It is closed-cell, so the cells are sealed from each other and water cannot soak through the core.
Can it be used outdoors and at sea?
Yes. EPDM has excellent resistance to ozone, UV and weathering, which suits exposed deck hatches.
Do the chamfered corners matter?
They help the seal close evenly against the coaming and reduce snagging as the hatch opens and shuts, extending seal life.
Need help matching a hatch seal to your channel? Contact our team with the channel width and closing gap and we will recommend the right size.
Product details
| SKU | IP-HSEA-50X30-10 |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Watertight Hatch Seal – 50mm x 30mm – 10m or 20m Strip