
Rubber & FoamSKU IP-TPEPFC-20X8-25M
White TPE P Profile – Food Contact Grade – 20mm Flange x 8mm Hollow Bead – 25m Coil
A white, food-contact grade TPE P-profile, 20 mm wide with an 8 mm hollow bead. The thin 1 mm flange fixes flat to a frame and the soft hollow bead (6 mm bore, 1 mm wall) closes gaps on food machinery guards, hygienic cabinet doors, hatches and glazed panels. Supplied as one continuous 25 m coil (about £21.64 per metre inc VAT), held in stock for fast dispatch.
At a glance
- Size: 20 mm overall width × 8 mm high; Ø8 mm hollow bead with a Ø6 mm bore
- Wall and flange: 1 mm thick throughout, leaving about 12 mm of flat fixing face beyond the bead
- Grade: white thermoplastic elastomer (TPE) sold by the manufacturer as a food-contact grade
- Hardness: 60° Shore A, with a thin-walled bead that closes easily under light door pressure
- Working temperature: −40 °C to +90 °C
- Clean finish: non-marking, waterproof and lightweight, and it springs back to shape after repeated closing
- Tolerance: ISO 3302-1 class E2 on the section, L2 on length
Technical drawing

Specifications
| Property | Value | Test method / source |
|---|---|---|
| Profile type | P-section: flat flange with a round hollow sealing bead | Manufacturer's section drawing |
| Overall width (flange length) | 20 mm | Nominal, manufacturer |
| Overall height (bead outside diameter) | 8 mm | Nominal, manufacturer |
| Bead bore (inside diameter) | 6 mm | Nominal, manufacturer drawing |
| Bead wall | 1 mm | Calculated: (8 − 6) ÷ 2; matches stated 1 mm thickness |
| Flange thickness | 1 mm | Nominal, manufacturer |
| Flat flange beyond the bead | ≈ 12 mm | Calculated: 20 − 8 |
| Suggested closed gap | ≈ 4.5 to 6 mm | Our fitting guide (bead squeezed by a quarter to a half) |
| Coil length | 25 m, one continuous length | Unit of sale |
| Colour | White, non-marking | Manufacturer |
| Material | Thermoplastic elastomer (TPE), food-contact grade | Manufacturer product data |
| Hardness | 60° Shore A | Manufacturer product data |
| Maximum working temperature | +90 °C | Manufacturer product data |
| Minimum working temperature | −40 °C | Manufacturer product data |
| Dimensional tolerance | Class E2 (cross-section), L2 (length) | ISO 3302-1 |
| Density | Not stated by the manufacturer for this profile | – |
| Tensile strength / elongation at break | Not stated by the manufacturer for this profile | – |
| Tear strength / compression set | Not stated by the manufacturer for this profile | – |
All values are the manufacturer's figures for this exact profile, except where marked as calculated. We list the properties the manufacturer does not publish so you know exactly what is and is not specified; ask us if your application needs them.
Materials and compliance
This profile is extruded from a white thermoplastic elastomer that the manufacturer supplies as a food-contact grade and lists for food processing equipment. TPE is a rubber-like thermoplastic: it is non-marking, waterproof and recyclable, and it recovers its shape after repeated compression.
The manufacturer does not name a specific regulation for this exact profile (for example FDA 21 CFR, EC 1935/2004 or EU 10/2011), and states no WRAS, REACH or RoHS approval, so we do not claim one. If your audit needs a declaration of compliance, contact us before ordering and we will request the paperwork.
Typical uses
- Door and guard seals on food processing and packaging machinery
- Hygienic cabinet, cupboard and display case doors
- Access hatches and inspection covers on water treatment and purification equipment
- Edge seals for glass and sheet panels in frames and showcases
- Lid seals on electrical and control enclosures
- Splash and dust seals on equipment housings and architectural joinery
How it fits

- Fix the flat flange to the frame so the bead meets a clean closing face
- Degrease the surface, then bond the flange with a contact adhesive suited to TPE, or hold it under a clamping strip
- Lay the profile in without stretching it; stretched seal shrinks back and opens gaps at the ends
- Aim for the bead to be squashed by about a third when closed, which is a closed gap of roughly 4.5 to 6 mm
- Notch the flange at corners so the bead runs round in one piece
Which version do I need?
| Profile | Best for |
|---|---|
| White 20 mm flange × 8 mm hollow bead, food-contact grade (this one) | Food and hygienic areas, soft close on light doors |
| White 20 × 8 mm TPE P seal, 40 Shore A, 1.5 mm wall | Same footprint in a softer, thicker-walled food-contact compound |
| Black 20 mm flange × 8 mm hollow bulb | General use where food contact is not needed |
| White 30 × 15 mm food-contact P profile | Bigger gaps in food areas |
How much do I need?
Add up the perimeter of every door or lid and allow about 5% for trimming and corners. Example: four machine guard doors of 600 × 800 mm need 4 × 2.8 m = 11.2 m, plus 5% ≈ 11.8 m, so one 25 m coil covers them twice over.
Frequently asked questions
Is it suitable for food contact?
The manufacturer supplies this white TPE as a food-contact grade and lists it for food processing equipment. It does not name a specific regulation for this profile, so if you need a declaration of compliance for an audit, ask us before you order.
Is the 8 mm bead hollow or solid?
Hollow, with a 6 mm bore and a 1 mm wall. That makes it close very easily, so light doors and lids still latch.
What gap does it seal?
Measure the gap with the door shut. This bead suits a closed gap of roughly 4.5 to 6 mm, where it is squeezed by a quarter to a half. For bigger gaps choose a larger bead.
How do I fix it?
Bond the 1 mm flange with a contact adhesive suitable for TPE, or trap it under a metal or plastic clamping strip. Clean and degrease the surface first. Use the flat part of the flange, about 12 mm wide, for any fixing.
How do I cut and join it?
Cut square with a sharp knife or fine-toothed blade. For a continuous ring, butt-join the ends with a cyanoacrylate (instant) adhesive suited to TPE and thermoplastic rubbers; TPE can also be heat-welded. Notch the flange at corners rather than cutting the bead.
What temperatures can it take?
It is rated from −40 °C to +90 °C, so it suits chillers, cold rooms and normal wash-down areas. Do not use it on oven doors or near heaters; choose silicone for those.
Will it mark stainless steel or painted panels?
No. The compound is non-marking.
Is this a full coil or cut lengths?
One continuous 25 m coil, so long runs need no joins.
Need help choosing the right seal? Call +44 1282 277786, email sales@industrial-polymers.co.uk or contact our team.
Product details
| SKU | IP-TPEPFC-20X8-25M |
|---|---|
| Weight | 1.1 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:White TPE P Profile – Food Contact Grade – 20mm Flange x 8mm Hollow Bead – 25m Coil