
Rubber & FoamSKU IP-TPEP-16X6-STD
Black TPE P Profile – 16mm Flange x 6mm Hollow Bulb – 25m Coil
A compact black TPE P-profile, 16 mm wide with a 6 mm hollow bulb. The flat 2.5 mm flange fixes to the frame and the soft hollow bulb (2 mm bore) closes small gaps on enclosure doors, cabinet lids, hatches and glazed panels. Supplied as one continuous 25 m coil (works out at about £17.22 per metre inc VAT), held in stock for fast dispatch.
At a glance
- Size: 16 mm overall width × 6 mm high; Ø6 mm hollow bulb with a Ø2 mm bore
- Flange: 2.5 mm thick, about 10 mm of flat fixing face beyond the bulb
- Material: SEBS-type thermoplastic elastomer (TPE), 50° Shore A, black and non-marking
- Working temperature: −40 °C to +90 °C
- Tough and stretchy: 7.7 MPa tensile strength, 700% elongation at break (compound data)
- Outdoor-ready: the compound resists weathering and ageing, and handles dilute acids and alkalis well
- Recyclable: the TPE compound is 100% recyclable
Technical drawing

Specifications
| Property | Value | Test method / source |
|---|---|---|
| Profile type | P-section: flat flange with a round hollow sealing bulb | Manufacturer's section drawing |
| Overall width (flange length) | 16 mm | Nominal, manufacturer |
| Overall height (bulb diameter) | 6 mm | Nominal, manufacturer |
| Bulb bore (inner diameter) | 2 mm | Nominal, manufacturer datasheet |
| Bulb wall | ≈ 2 mm | Calculated: (6 − 2) ÷ 2 |
| Flange thickness | 2.5 mm | Nominal, manufacturer |
| Flat flange beyond the bulb | ≈ 10 mm | Calculated: 16 − 6 |
| Coil length | 25 m, one continuous length | Unit of sale |
| Colour | Black, non-marking | Manufacturer |
| Material | Thermoplastic elastomer (TPE), SEBS type | Manufacturer datasheet |
| Hardness (this profile) | 50° Shore A | Manufacturer product data |
| Hardness (TPE compound sheet) | 60 ± 5° Shore A | ISO 868 (compound datasheet) |
| Density | ≈ 1.10 g/cm³ | ISO 1183-1 method A |
| Tensile strength | 7.70 N/mm² (MPa) | ISO 37 / DIN 53504 |
| Elongation at break | 700% | ISO 37 / DIN 53504 |
| Compression set, 72 h at 23 °C | 21% | ASTM D395 method B |
| Compression set, 22 h at 70 °C | 41% | ASTM D395 method B |
| Tear strength | Not stated by the manufacturer for this compound | – |
| Working temperature | −40 °C to +90 °C | Manufacturer product data |
| Dimensional tolerance | Class E2 (cross-section), L2 (length) | ISO 3302-1 |
| Weathering / chemicals | Good resistance to outdoor ageing, acids and bases | Manufacturer datasheet |
| Recyclability | 100% recyclable compound | Manufacturer datasheet |
Physical properties are for the TPE compound used to extrude this profile. The manufacturer's general compound sheet quotes a wider temperature range and a 60 ± 5 Shore A hardness; the product-specific figures (50 Shore A, −40 °C to +90 °C) are the ones we rate this profile at.
Materials and compliance
This profile is extruded from a general-purpose SEBS thermoplastic elastomer. It is non-marking, waterproof and recyclable, and it springs back to shape after repeated compression.
The manufacturer does not state any food-contact (FDA, EC 1935/2004), WRAS, REACH or RoHS approval for this exact profile, so we do not claim one. If you need a food-contact grade seal, see our white food-contact TPE P seal, 20 × 8 mm, or contact us for paperwork on other sizes.
Typical uses
- Door and lid seals on small electrical and control enclosures
- Dust and draught seals on cabinet, cupboard and locker doors
- Edge seals for glass and sheet panels in frames and showcases
- Access hatches, inspection covers and machine guards
- Splash seals on equipment housings and architectural joinery
How it fits

- Fix the flat flange to the frame so the bulb meets a clean closing face
- Degrease the surface, then bond the flange with a contact adhesive suited to TPE, or hold it under a clamping strip
- Lay the profile in without stretching it; stretched seal shrinks back and opens gaps at the ends
- Aim for the bulb to be squashed by about a third when closed, which is a closed gap of roughly 3 to 4.5 mm
- Notch the flange at corners so the bulb runs round in one piece
Which size do I need?
| Profile | Best for |
|---|---|
| 16 mm flange × 6 mm hollow bulb (this one) | Narrow fixing faces and the smallest gaps |
| 21 mm flange × 6 mm hollow bulb | Same small bulb with a wider fixing flange |
| 27 mm flange × 7 mm bulb | Slightly bigger gaps, wide fixing face |
| 20 mm flange × 8 mm hollow bulb | Larger gaps with a very soft close |
| 28 mm flange × 10.5 mm bulb | Bigger gaps and uneven frames |
How much do I need?
Add up the perimeter of every door or lid and allow about 5% for trimming and corners. Example: six enclosure doors of 400 × 500 mm need 6 × 1.8 m = 10.8 m, plus 5% ≈ 11.4 m, so one 25 m coil does them twice over.
Frequently asked questions
Is the 6 mm bulb hollow or solid?
Hollow, with a 2 mm bore running through it. That makes it close more easily than a solid bead of the same size, so light doors still latch.
What gap does it seal?
Measure the gap with the door shut. This bulb suits a closed gap of roughly 3 to 4.5 mm, where it is squeezed by about a third. For gaps over 5 mm pick the 8 mm or 10.5 mm bulb versions.
How do I fix it?
Bond the 2.5 mm flange with a contact adhesive suitable for TPE, or trap it under a metal or plastic clamping strip. Clean and degrease the surface first. For a mechanical fixing, use the flat part of the flange, about 10 mm wide, beyond the bulb.
How do I cut and join it?
Cut square with a sharp knife or fine-toothed blade. For a continuous ring, butt-join the ends with a cyanoacrylate (instant) adhesive suited to TPE/thermoplastic rubbers; TPE can also be heat-welded. Notch the flange at corners rather than cutting the bulb.
What temperatures can it take?
We rate this profile from −40 °C to +90 °C. Do not use it next to oven doors, heaters or hot exhausts; choose silicone for those.
Can it be used outdoors?
Yes. It is waterproof and the SEBS compound resists weathering and ageing well.
Is it food safe?
No food-contact approval is stated for this black profile. Use our white food-contact grade TPE P seals for direct food contact.
Will it mark painted or powder-coated panels?
No. The compound is non-marking.
Is this a full coil or cut lengths?
One continuous 25 m coil, so long runs need no joins.
Need help choosing the right seal? Call +44 1282 277786, email sales@industrial-polymers.co.uk or contact our team.
Product details
| SKU | IP-TPEP-16X6-STD |
|---|---|
| Weight | 3.31 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Black TPE P Profile – 16mm Flange x 6mm Hollow Bulb – 25m Coil