
Rubber & FoamSKU IP-BFSS-22X14-18M
EPDM B Fender with Stainless Steel Strip – 22mm x 14mm – 18m Length
A slim EPDM rubber B fender, 22 mm wide and 14 mm high, supplied with a 304 stainless steel retaining strip already in its slot. You screw through the strip, so the fender goes on in a straight line with even clamping, and the screw heads sit below the two rounded lobes where nothing can catch on them. It comes as one continuous 18 m length: enough to run both sides of a small dinghy, or a long wall, without joins.
At a glance
- Size: 22 mm wide × 14 mm high, the smallest B fender profile we stock
- Fixing strip included: 8 mm wide × 0.76 mm (22 gauge) 304 stainless steel
- Material: black EPDM, 70° Shore A, rated for UV, ozone and outdoor use
- Length: 18 m continuous, about 0.39 kg per metre (about 7 kg in total)
- Price per metre: about £24.17 inc VAT (£435.00 ÷ 18 m)
- In stock for same-day dispatch
Where it is used
- Rubbing strake on dinghies, tenders, rowing boats and small workboats
- Edge protection on pontoons, jetties and boarding platforms where a big fender would get in the way
- Bump strip on van, truck and ambulance bodywork, tail lifts and load-bed edges
- Wall, door-frame and corner protection in factories, loading bays, car parks and corridors
- Shopfitting and display edges that need a neat, low bumper
Technical drawing

Overall width, height and strip size are manufacturer values. Lobe radius, slot width and cavity depth follow the manufacturer's section for illustration and are not specified dimensions.
Specifications
| Property | Value | Test method / note |
|---|---|---|
| Profile | B fender: flat back, twin rounded lobes, open T-slot | - |
| Overall width | 22 mm | Nominal |
| Overall height (projection from surface) | 14 mm | Nominal |
| Retaining strip width | 8 mm | Nominal |
| Retaining strip thickness | 0.76 mm (22 gauge) | Nominal |
| Retaining strip material | 304 stainless steel | - |
| Fender material | EPDM (ethylene propylene diene monomer) | - |
| Colour | Black | - |
| Length supplied | 18 m, one continuous piece | - |
| Weight | 0.39 kg/m (about 7.0 kg per 18 m) | - |
| Hardness | 70° Shore A | ISO 7619-1 / DIN 53505 / ASTM D2240 |
| Tensile strength | 7.2 MPa | ISO 37 / DIN 53504 / ASTM D412 |
| Elongation at break | 305 % | ISO 37 / DIN 53504 / ASTM D412 |
| Tear strength | 55 N/mm | ISO 34-1 |
| Compression set | 23 % (24 h at 100 °C, 25 % deflection) | ISO 815 |
| Density | 1.28 g/cm³ | ISO 2781 / DIN 53479 / ASTM D297 |
| Rebound resilience | 23 % | DIN 53512 / ASTM D1054 |
| Ozone resistance | No cracking (72 h at 40 °C, 50 pphm) | ISO 1431-1 method A |
| Service temperature | About -40 °C to +120 °C | Typical for EPDM, not tested on this profile |
| Dimensional tolerance | Not stated by the manufacturer | Ask us if you need a tolerance for a critical fit |
Materials and compliance
The fender is EPDM rubber and the retaining strip is 304 stainless steel. EPDM is chosen for outdoor and marine use because it holds up to sunlight, ozone, rain and salt air without cracking; the ozone result above is the manufacturer's test on this compound. The manufacturer is ISO 9001:2015 registered. No product approvals (for example FDA, WRAS, REACH or RoHS) are stated for this item, so we do not claim any. If you need a declaration for your project, contact us before ordering.
How it fits

- Measure the run and add a little for trimming. Cut the rubber with a sharp knife and the steel strip with a hacksaw or snips, then file the cut end smooth.
- Hold the fender straight with the flat back against the surface and the slot facing out.
- Drill through the strip and into the surface at about 300 mm centres, starting about 50 mm in from each end.
- Fix with countersunk stainless screws (A4 marine grade on boats; plugs or anchors on masonry). The head must pass through the slot opening, so check your screws against the fender before buying a box. Do not over-tighten.
- On boats, bed each screw hole in marine sealant.
How much do I need?
Add up every edge you want to protect and allow about 5 % for trimming. A 4.5 m dinghy needs roughly 9.5 m to run down both sides, so one 18 m length covers it with spare. A 15 m wall run fits on one length; 30 m needs two.
Which size do I need?
| Profile | Choose it when |
|---|---|
| 22 × 14 mm with steel strip (this one) | You want a slim fender that screws on straight, with hidden screw heads |
| 22 × 14 mm plain, 36 m | Same profile without the strip, for adhesive fixing or longer runs |
| 32 × 16 mm with steel strip | You want a little more rubber between the knock and the surface |
| 44 × 19 mm with steel strip | Heavier boats, loading bays and harder impacts |
Frequently asked questions
Is the stainless steel strip included?
Yes. The 8 mm × 0.76 mm 304 stainless strip comes in the slot along the full 18 m. You only need to buy screws.
How do I fix it?
Drill through the strip at about 300 mm centres and screw into the surface with countersunk stainless screws. The screw heads sit down in the slot, below the rubber lobes, so they are protected and do not scratch anything that rubs along the fender.
Which way round does it go?
The flat back goes against the boat, wall or panel. The two rounded lobes and the slot face outwards.
Is 22 × 14 mm big enough for my boat?
It suits dinghies, tenders and small craft, and any edge where a slim profile matters. It stands 14 mm proud of the surface. For heavier boats or harder knocks choose the 32 × 16 mm or 44 × 19 mm B fender.
Can it be used outdoors and in salt water?
Yes. EPDM resists UV, ozone, rain and salt air, and the manufacturer's ozone test shows no cracking. The strip is 304 stainless steel. For constant immersion in seawater, rinse it with fresh water from time to time.
What temperature can it take?
EPDM is typically used from about -40 °C to +120 °C. That is a typical figure for the material; the manufacturer has not published a temperature test for this profile.
How do I cut and join it?
Cut the rubber with a sharp knife and the strip with a hacksaw or tin snips, then file off any burr. Butt two lengths tightly together and put a fixing about 50 mm either side of the joint. Around tight corners, cut a small V-notch in the back of the rubber and the strip so it bends without kinking.
Will it go round a curved hull?
Yes, it bends easily round the gentle curves of a gunwale. Fixings every 300 mm, or closer on tight curves, hold it to the shape.
Can I buy a shorter length?
This item is one continuous 18 m length. Contact us if you need a different length or a quantity for a fleet.
Questions about sizing or fixing? Call +44 1282 277786 or email sales@industrial-polymers.co.uk.
Product details
| SKU | IP-BFSS-22X14-18M |
|---|---|
| Weight | 15.48 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:EPDM B Fender with Stainless Steel Strip – 22mm x 14mm – 18m Length