
Rubber & FoamSKU IP-EPDMB-32X16-STD
EPDM Rubber B Fender – 32mm x 16mm with Stainless Steel Strip – 15m Coil
This EPDM rubber B fender 32mm x 16mm with stainless steel strip is a compact, black impact strip for protecting the edges of trailers, walls, doors and equipment. It is sold as one continuous 15m coil, with an 8mm wide 304 stainless steel strip already set in the base slot so you can screw or bolt it through for a secure mechanical fixing.
At a glance
- Black EPDM rubber B profile, 32mm wide x 16mm high
- 8mm wide x 0.76mm (22 gauge) 304 stainless steel retaining strip in the base
- One continuous 15m coil for long, joint-free runs
- 70° Shore A: firm enough to hold its shape, soft enough to cushion knocks
- EPDM resists UV, ozone and weathering for indoor or outdoor use
- Twin rounded lobes spread the load of an impact along the strip
Typical uses
- Rubbing strake and edge fender on small boats, tenders and pontoons
- Bump strip on trailer sides, van bodies and specialist vehicles
- Low-level wall guard and kick strip in warehouses and plant rooms
- Protecting door frames, cabinet edges and machine panels from trolleys
- Discreet impact protection in shopfitting and commercial interiors
Which one do I need?
| Profile | Best for |
|---|---|
| 22mm x 14mm with strip | Very light knocks, slim edges and small craft |
| 32mm x 16mm with strip (this product) | General-purpose edge protection with a screw-through fixing strip |
| 44mm x 19mm with strip | Larger boats, trailers and busier loading areas |
| 32mm x 16mm without strip | Same profile where you will fix with adhesive or your own batten |
Technical drawing
Specification
| Material | EPDM rubber |
| Colour | Black |
| Profile | B fender, 32mm wide x 16mm high |
| Retaining strip | 304 stainless steel, 8mm wide x 0.76mm (22 gauge) |
| Unit of sale | One 15m coil |
| Hardness | 70° Shore A |
| Tensile strength | 7.2 MPa |
| Elongation at break | 305% |
| Tear strength | 55 N/mm |
| Compression set | 23% (24 h at 100°C, 25% deflection) |
| Density | 1.28 g/cm³ |
| Ozone resistance | No cracking after 72 h at 40°C, 50 pphm |
How much do I need?
Measure every edge you want to protect and add about 5% for trimming. Example: two sides of a 6m trailer plus a 2.4m rear edge comes to 14.4m, plus 5% is about 15.1m, so one 15m coil will cover it if you butt the ends carefully. For longer runs, order a second coil.
Fitting tips
- Mark fixing points every 250-300mm along the centre slot, and closer at each end.
- Drill through the stainless strip and use stainless screws or bolts so the fixing does not rust and stain.
- Cut the rubber with a sharp knife and the steel strip with a hacksaw; dress the cut end of the strip so no sharp edge is left.
- Fit the fender with the flat back tight to the surface and the two rounded lobes facing outwards.
Complete your project
- EPDM Rubber B Fender with Stainless Steel Strip – 44mm x 19mm – 15m Roll
- EPDM B Fender with Stainless Steel Strip – 22mm x 14mm – 18m Roll
- EPDM Rubber B Fender – 32mm x 16mm – 30m Coil
Questions
Can this B fender be used outdoors?
Yes. EPDM rubber has very good resistance to sunlight, ozone and weathering, so it suits boats, trailers and exterior walls.
Is the stainless steel strip pre-drilled?
No. The strip is plain, so you can choose fixing positions to suit the edge you are protecting and drill through it on site.
How do I cut it to length?
Cut the rubber with a sharp knife, then cut the steel strip with a fine-tooth hacksaw. Remove any burrs before fitting.
What is the difference from the version without a strip?
The profile is the same 32mm x 16mm B shape. The strip version gives a stronger screw-through fixing; the plain version is lighter and comes in a longer coil.
Will it bend around corners?
It follows gentle curves such as a boat gunwale. For a sharp 90° corner, mitre the ends and fix each piece separately.
Need help choosing the right fender or edge protector? Contact our team and we will be glad to advise.
Product details
| SKU | IP-EPDMB-32X16-STD |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:EPDM Rubber B Fender – 32mm x 16mm with Stainless Steel Strip – 15m Coil