
Rubber & FoamSKU IP-EBF-44X19-SS15
EPDM Rubber B Fender with Stainless Steel Strip – 44mm x 19mm – 15m Roll
This EPDM rubber B fender with stainless steel strip is a 44mm wide x 19mm high twin-lobe buffer that screws flat to walls, door frames and vehicle bodies to soak up repeated knocks. It is sold as one 15m roll, supplied complete with a 304 stainless steel fixing strip.
At a glance
- 44mm x 19mm B profile: two rounded lobes on a flat fixing base
- 304 stainless steel strip, 13mm x 0.76mm (22 gauge), forms a solid fixing core along the profile
- 70 Shore A EPDM rubber with good UV, ozone and weather resistance
- Drill through rubber and strip for screwed or bolted fixing
- Weight about 0.92kg per metre
- One continuous 15m roll
Typical uses
- Impact strip along loading bay walls and door frames
- Rubbing strip on ambulances, vans, trucks and trailers
- Bump protection in shopfitting and on corridor walls
- Marine fendering on small craft and pontoon edges
Which one do I need?
| Fixing through the fender | This 44mm x 19mm B fender with stainless strip, which spreads the load of each screw |
| Longer runs, no strip needed | Our plain 44mm x 19mm EPDM B fender in a 30m roll |
| Heavier knocks | Step up to our 60mm x 32mm EPDM B fender |
| Light trim duty | Our 32mm x 16mm or 22mm x 14mm EPDM B fenders |
Technical drawing
Specification
| Material | EPDM rubber |
| Profile | B fender, 44mm wide x 19mm high |
| Colour | Black |
| Hardness | 70 Shore A |
| Fixing strip | 304 stainless steel, 13mm x 0.76mm (22 gauge) |
| Roll length | 15m |
| Weight | 0.92kg per metre |
| Tensile strength | 7.2 MPa |
| Elongation at break | 305% |
| Tear strength | 55 N/mm |
| Compression set | 23% (24h at 100°C, 25%) |
| Density | 1.28 g/cm³ |
| Ozone resistance | No cracking (72h at 40°C, 50pphm) |
How much do I need?
Add up every edge to protect. Example: a loading bay door opening 3m wide with a fender across the head and down both 3m jambs needs 3 + 3 + 3 = 9m, so one 15m roll covers it with 6m left for a second, shorter run. Two identical doorways need 18m, so order two rolls.
Fitting tips
- Clean and check the mounting surface; it must be flat and sound.
- Drill pilot holes through the rubber and the stainless strip about every 300mm, closer at the ends.
- Use fixings to suit the substrate: masonry anchors in brick or concrete, machine screws or rivets on steel panels.
- Cut the rubber with a sharp knife and the strip with a hacksaw; butt joints tight on long runs.
Complete your project
- EPDM Rubber B Fender 44mm x 19mm – 30m Roll
- EPDM Sponge Rear Door Seal – 20mm x 21mm
- Industrial Rubber Cable Protector – 140mm x 36mm
Questions
Can this B fender be used outdoors?
Yes. EPDM resists UV, ozone and weathering, so it suits exterior walls, vehicles and marine edges.
What does the stainless steel strip do?
It acts as a fixing core and spreads the load of each screw, so fixings do not pull through the rubber under impact.
Is the strip included?
Yes, the 304 stainless steel strip is supplied with the 15m roll of EPDM B fender.
How do I cut it?
Cut the rubber with a sharp utility knife, then saw through the strip with a fine-tooth hacksaw.
Do you sell it in longer lengths?
Yes, the plain 44mm x 19mm B fender is also sold as a 30m roll without the steel strip.
Need help choosing a fender size? Contact our team.
Product details
| SKU | IP-EBF-44X19-SS15 |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:EPDM Rubber B Fender with Stainless Steel Strip – 44mm x 19mm – 15m Roll