
Rubber & FoamSKU IP-SGDS-13.4X11-10M
Self-Grip Door Seal with Sponge Side Bulb – 13.4mm x 11mm – EPDM, Fits 1-2mm Panels – 10m to 100m
Price shown updates with the option you pick.
A push-on door and hatch seal for 1 mm to 2 mm panel edges: a solid EPDM grip with a steel wire carrier, plus a soft EPDM sponge bulb on the side. The seal is 13.4 mm wide and 11 mm high. The grip is 7.6 mm wide, with a 2.2 mm mouth, and holds the panel edge with an internal fin and the steel carrier, so no glue is needed. The closed-cell sponge bulb, about 5.8 mm wide, sits against the frame or the opposite door when it closes and keeps out water, dust, draughts and noise. Choose any length from 10 m to 49 m in one continuous piece, a full 50 m coil, or longer runs up to 100 m. It is in stock in the UK for same-day dispatch.
At a glance
- Fits: sheet metal, aluminium, GRP and plastic door, hatch and panel edges from 1 mm to 2 mm thick
- Size: 13.4 mm overall width × 11 mm height. The grip is 7.6 mm wide with a 2.2 mm mouth.
- Grip: solid EPDM, 70 ± 5 Shore A, with a steel wire carrier and one angled internal fin. It pushes on by hand, with no adhesive.
- Seal: closed-cell EPDM sponge bulb with 0.6 g/cm³ density and 0.98 % water absorption. Aim for 30 % to 40 % squeeze and never more than 50 %.
- Working temperature: −40 °C to +70 °C, indoors or outdoors, with good resistance to UV, ozone and weathering
- Weight: 0.11 kg per metre
- Lengths: 10 m to 49 m at £7.98 per metre, a 50 m coil for £267.00 (£5.34 per metre), and up to 100 m for £504.00 (£5.04 per metre)
Technical drawing

All dimensions are in mm and nominal. The manufacturer gives the 13.4, 7.6, 11 and 2.2 mm dimensions. The wall, fin, carrier and bulb are drawn in proportion to the manufacturer's section and have no separate tolerance.
Specifications
| Property | Value | Test method / basis |
|---|---|---|
| Dimensions and fit | ||
| Profile | Self-gripping U grip with steel wire carrier and one internal fin, with a closed-cell sponge bulb on one side | Manufacturer drawing |
| Overall width (grip + bulb) | 13.4 mm | Manufacturer drawing, data sheet and product data |
| Overall height | 11 mm | Manufacturer drawing, data sheet and product data |
| Grip width | 7.6 mm | Manufacturer drawing |
| Mouth opening (unflexed) | 2.2 mm | Manufacturer drawing |
| Panel thickness it fits | 1 mm to 2 mm | Manufacturer data sheet and product data |
| Sponge bulb width, including the two small lips | About 5.8 mm | Calculated: 13.4 − 7.6 |
| Recommended bulb compression | 30 % to 40 % (about 1.7 mm to 2.3 mm of squeeze). The technical table gives 40 % as the maximum, and the fitting notes say never more than 50 %. | Manufacturer product data |
| Dimensional tolerance | Not stated for this profile | Ask us if you need it |
| Weight | 0.11 kg per metre (about 5.5 kg for a 50 m coil) | Manufacturer data |
| Colour | Black | Manufacturer |
| Working temperature (complete seal) | −40 °C to +70 °C | Manufacturer product data. The sponge sets the upper limit. |
| Solid EPDM grip (measured value, with the requirement in brackets) | ||
| Hardness | 70 to 71 Shore A (requirement 70 ± 5) | ISO 7619-1 |
| Tensile strength | 7.8 MPa (minimum 7.5 MPa) | ISO 37 |
| Elongation at break | 340 % (minimum 300 %) | ISO 37 |
| Tear resistance | 22.18 N/mm (minimum 8 N/mm) | ISO 34-1 |
| Compression set, 22 h at 100 °C | 23.12 % (maximum 35 %) | ISO 815 |
| Hardness change after low-temperature ageing, 168 h at −10 °C | +4 Shore A (maximum +10) | DIN 53505 |
| Ozone resistance, 72 h at 40 °C, 50 pphm | No cracks | ISO 1431-1 A |
| UV resistance | No migration | ASTM D 1148 |
| Brittleness point, 24 h at −40 °C | No cracks | ISO 812 |
| Working temperature of the grip compound | −40 °C to +120 °C | Manufacturer data sheet |
| Carrier | Steel wire (metal insert), moulded into the grip for its full length | Manufacturer |
| EPDM sponge bulb | ||
| Compound | Closed-cell EPDM sponge | Manufacturer data sheet |
| Density | 0.6 g/cm³ | TS 2817 ISO 2781 |
| Tensile strength | 2.8 MPa | TS ISO 37 |
| Elongation at break | 140 % | TS ISO 37 |
| Compression deflection | 42 kPa | ASTM D 1056 |
| Water absorption | 0.98 % | ASTM D 1056 |
| Ozone resistance, 72 h at 40 °C, 50 pphm | No cracking | ISO 1431-1 A |
| Thermal conductivity | 0.15 W/m·K | ASTM C 518 |
| Recovery after ageing | 82 % | Manufacturer data sheet; method not stated |
| Working temperature | −40 °C to +70 °C | Manufacturer data sheet |
Lengths and prices
Prices include VAT. Lengths from 10 m to 50 m are one continuous piece with no joins.
| Length | Price | Per metre | Supplied as |
|---|---|---|---|
| 10 m to 49 m (1 m steps) | £79.80 to £391.02 | £7.98 | One continuous cut length |
| Examples: 10 m / 20 m / 30 m / 40 m | £79.80 / £159.60 / £239.40 / £319.20 | £7.98 | One continuous cut length |
| 50 m full coil | £267.00 | £5.34 | One continuous coil |
| 60 m / 70 m / 80 m / 90 m | £320.40 / £373.80 / £427.20 / £480.60 | £5.34 | A 50 m coil plus one cut length for the rest |
| 100 m | £504.00 | £5.04 | Two 50 m coils |
Tip: for 34 m or more, the full 50 m coil costs less than a cut length. It is priced at our 50 m+ bulk rate.
To work out how much you need, measure all round the door or hatch opening and add about 5 % for trimming. For example, a 900 × 2000 mm cabinet door has a 5.8 m perimeter, so eight doors need 46.4 m. With 5 % extra that is 48.7 m, so the 50 m coil is the cheaper choice.
How it fits

- Check the edge. It should be 1 mm to 2 mm thick, deburred, clean and dry. Decide which side of the panel the frame or the other door closes against. The bulb must face that side.
- Push on. Start in the middle of a straight run, away from a corner. Press the grip fully home by hand as you work along the edge. Do not stretch the seal as you go, because it will shrink back and leave gaps at the ends.
- Seat it. Tap along the top of the grip with a rubber or plastic mallet until the panel edge reaches the bottom of the channel. Never hit the sponge bulb.
- Check the squeeze. Close the door. The bulb should be squashed by about a third (30 % to 40 %). If it is squashed flat, the gap is too small for this profile.
- Finish. Cut through the rubber and carrier with side cutters or a sharp knife and snips. Butt the two ends tightly together at the bottom of the door, where they are least visible.
Typical uses
- Doors and access hatches on control cabinets, machine enclosures, kiosks and plant rooms
- Garage, shed and workshop doors made from thin sheet steel or aluminium
- Car, van, bus and train doors, side windows, boot lids and interior side panels
- Hatches and lockers on boats and marine equipment
- Furniture, display cases and glazed doors where a cushioned, quiet close is wanted
Which self-grip seal do I need?
Measure the panel edge thickness and the gap the seal has to close when the door shuts. For 30 % to 40 % squeeze across this bulb, the gap should be about 3.5 mm to 4 mm. Related profiles for 1 mm to 2 mm edges:
- EPDM Self-Grip Door Seal 12.5 × 8 mm: a smaller, lower profile
- This seal, 13.4 × 11 mm: a 5.8 mm sponge side bulb
- EPDM Self-Grip Door Seal 15.5 × 10 mm: a wider side bulb for larger gaps
- EPDM Self-Grip Edge Trim 7.4 × 9.7 mm: the same type of grip with no bulb, for edge protection only
Materials and compliance
Both the grip and the bulb are EPDM, which suits outdoor doors and hatches. The manufacturer quotes excellent resistance to UV, ozone and weathering and good resistance to chemicals. EPDM handles water, steam, dilute acids and alkalis, and many cleaning products well. Like all EPDM, it is not suitable for petrol, diesel, mineral oils or greases. The steel carrier is fully enclosed in rubber except at the cut ends.
The manufacturer does not state any product approvals for this seal (such as FDA, EC 1935/2004, WRAS, REACH or RoHS), so we do not claim any. If you need a declaration for your application, contact us before ordering.
Frequently asked questions
Do I need glue to fit it?
No. The steel wire carrier and the internal fin clamp the grip onto the panel edge. You push it on by hand and seat it with a rubber mallet. With no adhesive, it can be pulled off and refitted.
What thickness of panel does it fit?
Edges from 1 mm to 2 mm thick. On thinner edges it will not grip firmly, and thicker edges will not go fully into the 2.2 mm mouth.
Which way round does the bulb go?
The bulb goes on the side that closes against the frame, the door stop or the other door. On a cabinet door that closes onto a flange, the bulb faces the flange.
How big a gap will it seal?
The bulb is about 5.8 mm wide. For a lasting seal it should be squeezed by 30 % to 40 %, so it suits a closed gap of about 3.5 mm to 4 mm between the panel face and the frame. Do not squeeze it by more than 50 %, or it will take a set and stop sealing.
Will it go round corners?
Yes. The carrier lets it follow radiused corners and curves. For a sharp 90° corner, cut a small V-notch in the base of the grip (never the bulb) so it folds round without bunching. Alternatively, cut and butt-join the seal at the corner.
How do I cut it and join the ends?
Cut through the rubber and the steel wire with side cutters, or score the rubber with a sharp knife and snip the wire. Cut the ends square and butt them tightly together. If a fully sealed join is needed, a drop of cyanoacrylate rubber adhesive on the sponge faces works well.
What temperatures can it take?
The complete seal is rated −40 °C to +70 °C. The solid grip compound itself is rated to +120 °C, but the sponge bulb sets the 70 °C limit, so keep it away from exhausts, ovens and similar heat sources.
Is it watertight?
Yes, when the bulb is squeezed by 30 % to 40 % all the way round. The sponge is closed-cell, with 0.98 % water absorption, so it does not soak up water.
When will it arrive?
All lengths are held in stock in the UK and dispatched the same working day, as shown in the dispatch message on this page.
If you need help choosing a profile, call +44 1282 277786 or email sales@industrial-polymers.co.uk.
Product details
| SKU | IP-SGDS-13.4X11-10M |
|---|---|
| Weight | 2.43 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Self-Grip Door Seal with Sponge Side Bulb – 13.4mm x 11mm – EPDM, Fits 1-2mm Panels – 10m to 100m