
Rubber & FoamSKU IP-EPDM-12X17-10M
EPDM Sponge Boot Seal – 12mm x 17mm – Adhesive Backed – 10m to 50m Lengths
Price shown updates with the option you pick.
This 12mm x 17mm EPDM sponge boot seal is a hollow, figure-of-eight sealing profile with a self-adhesive base, made to close boot lids, hatches, enclosure doors and access panels against air, water and dust. Choose one continuous length from 10m to 50m; each length is supplied as a single piece, and the full 50m coil is the best value per metre.
At a glance
- Expanded (sponge) EPDM rubber seal with a skinned outer surface
- 12mm wide x 17mm high, two hollow chambers that compress evenly
- Self-adhesive backing for quick, clip-free fitting
- Soft 40 Shore OO sponge seals against uneven or slightly bowed surfaces
- Non-marking black finish
- Good UV, ozone and weather resistance for indoor or outdoor use
Typical uses
- Boot lid, tailgate and hatch weather seals on restored and working vehicles
- Door and lid seals on electrical enclosures, cabinets and kiosks
- Draught and dust strip for access panels and inspection hatches
- Light cushioning and anti-rattle strip between panels
Which one do I need?
| Seal | Size | Best for |
|---|---|---|
| TPE sponge seal, adhesive backed | 9.5mm x 9.5mm | Small gaps on light panels and lids |
| EPDM sponge boot seal (this one) | 12mm x 17mm | Boot lids, hatches and enclosure doors with a medium closing gap |
| EPDM sponge hood seal | 28mm x 23mm | Larger lids and bonnets with wider, deeper gaps |
Technical drawing
Specification
| Material | Expanded EPDM sponge, skinned |
| Colour | Black |
| Size | 12mm wide x 17mm high |
| Profile | Hollow figure-of-eight, two chambers |
| Fixing | Self-adhesive backing |
| Hardness | 40° Shore OO |
| Density range | 0.5 – 0.9 g/cm³ |
| Water absorption | 5% max |
| Compression set (22 hours) | 50% |
| Oven ageing (7 days at 70°C) | ±30% |
| Unit of sale | One continuous length, 10m to 50m (50m = full coil) |
How much do I need?
Measure the full perimeter you need to seal and round up to the next whole metre. For example, four openings of 1.2m x 0.8m have a 4.0m perimeter each, so 16m in total; a 17m length leaves enough for trimming and tight joints. If you need 39m or more, the full 50m coil costs less than the longer cut lengths.
Fitting tips
- Clean the mounting face with a solvent wipe and let it dry fully before peeling the backing.
- Lay the seal on without stretching it; stretched sponge shrinks back and opens gaps at the joins.
- Cut slightly over-length and push the ends together so the joint is under light compression.
- Use a sharp knife or scissors for a square cut, and place joins away from corners where possible.
- Press firmly along the full length after fitting to bed the adhesive in.
Complete your project
- EPDM Sponge Hood Seal – 28mm x 23mm – Dual Hardness – 10m to 50m Lengths
- TPE Sponge Seal – Adhesive Backed – 9.5mm x 9.5mm – 100m Coil
- Watertight Hatch Seal – 35mm x 20mm – 10m Roll
Questions
How do I check the 12mm x 17mm boot seal suits my gap?
Measure the gap between the frame and the closed lid or door. The seal works by being squeezed, so the gap should be clearly smaller than its 17mm height; if the gap is larger, choose the bigger hood seal.
Is this EPDM sponge seal suitable for outdoor use?
Yes. EPDM has good resistance to UV, ozone and weathering and suits interior and exterior use.
Will it seal against an uneven surface?
Yes. The soft sponge and hollow profile compress to follow minor irregularities in the mating face.
Is my length supplied in one piece?
Yes. Each option is one continuous length; the 50m option is a full coil.
Need help choosing a seal? Contact our team.
Product details
| SKU | IP-EPDM-12X17-10M |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:EPDM Sponge Boot Seal – 12mm x 17mm – Adhesive Backed – 10m to 50m Lengths