
Rubber & FoamSKU IP-TPES-9.5X9.5-STD
TPE Sponge Seal – Self-Adhesive, Dual Hardness – 9.5mm x 9.5mm for 6–8mm Gaps – 100m Coil
A compact, self-adhesive TPE sponge seal, 9.5mm x 9.5mm, for closing gaps of 6mm to 8mm on cabinet and enclosure doors, hatches, lids and access panels. It is a dual-hardness extrusion: a firm, flat 30 Shore D TPE base carries the adhesive tape and keeps the strip straight, and a soft 15 Shore A TPE foam bulb (9mm diameter, hollow) squashes down when the door closes, so it seals against air, dust and water. Peel the liner, press it on, done. Supplied as one continuous 100m coil, black, from UK stock.
At a glance
- Size: 9.5mm wide x 9.5mm high; 9mm diameter hollow foam bulb on a 9.5mm wide flat base
- Seals gaps of 6mm to 8mm (closed-door clearance between the frame and the door)
- Dual hardness: 30 Shore D solid TPE base, 15 Shore A TPE foam bulb
- Self-adhesive: factory-applied adhesive tape with a peel-off liner, no glue or fixings needed
- Wide temperature range: −50°C to +75°C in use
- Light: 35g per metre; cuts cleanly with a sharp knife or heavy-duty scissors; 100% recyclable TPE
- Value: £1,133.91 per 100m coil inc VAT, which is about £11.34 per metre
Typical uses
- Electrical, control and instrument enclosure doors and covers
- Cabinet, locker and cupboard doors in workshops, vehicles and boats
- Inspection hatches, access panels and equipment lids
- Draught and dust sealing on doors and windows with a 6–8mm gap
- Light impact and surface protection along frames, edges and runs of pipe or cable
Technical drawing

Nominal dimensions in mm, free state before compression. The 9.5mm height is measured to the underside of the base; the adhesive tape and liner sit below it.
How it seals

Stick the flat base to the frame (or to the door) so the bulb faces the mating surface. When the door closes to a gap of 6–8mm, the hollow foam bulb is squeezed by roughly 15–35% and presses evenly along its length. The manufacturer rates the foam for about 25% working compression, which lets it take up small irregularities in the frame.
Which size do I need?
Measure the gap between the frame and the closed door (a stack of feeler gauges or a strip of card works). Choose a seal whose recommended gap range covers what you measured.
| Profile | Overall size | Coil | Best for |
|---|---|---|---|
| TPE sponge D profile 6 x 5.5mm | 6 x 5.5mm | 100m | Very small gaps |
| TPE sponge D profile 10 x 8mm | 10 x 8mm | 100m | Slightly lower, D-shaped bulb |
| TPE sponge seal 9.5 x 9.5mm (this item) | 9.5 x 9.5mm | 100m | 6–8mm gaps, round hollow bulb |
| TPE sponge seal 10 x 17mm | 10 x 17mm | 50m | Larger gaps, taller tube |
| TPE sponge seal 14 x 20mm | 14 x 20mm | 50m | Large, uneven gaps |
Specification
| Property | Value | Test method / source |
|---|---|---|
| Profile and dimensions | ||
| Profile | Self-adhesive bulb seal: hollow round foam tube on a flat solid base | – |
| Overall width (base) | 9.5 mm | Nominal, ISO 3302-1 |
| Overall height (to underside of base) | 9.5 mm | Nominal, ISO 3302-1 |
| Foam bulb outside diameter | 9.0 mm | Nominal, manufacturer drawing |
| Thickness (foam wall) | 2.0 mm | Manufacturer data |
| Bore of the bulb | ≈ 5 mm | Derived from 9mm diameter and 2mm wall |
| Gap (clearance) to fill | 6 mm to 8 mm | Manufacturer data sheet |
| Working compression of the foam | About 25% | Manufacturer data |
| Dimensional tolerance | ISO 3302-1 class E2 (cross-section) / L2 (length), quality level 2 | ISO 3302-1 |
| Materials | ||
| Base material | Solid thermoplastic elastomer (TPE) | Manufacturer data sheet |
| Base hardness | 30 Shore D | Shore D durometer (manufacturer data sheet) |
| Bulb material | TPE foam (sponge) | Manufacturer data sheet |
| Bulb hardness | 15 Shore A | Shore A durometer (manufacturer data sheet) |
| Colour | Black | – |
| Fixing | Adhesive tape on the base, with peel-off liner | – |
| Performance | ||
| Use temperature | −50 °C to +75 °C | Manufacturer data sheet |
| Weathering | Good UV and weather resistance, indoor and outdoor use | Manufacturer data |
| Recyclability | 100% recyclable TPE | Manufacturer data |
| Tensile strength, elongation, tear, compression set | Not published for this profile | Ask us if you need test data |
| Supply | ||
| Weight | 35 g per metre (about 3.5 kg per coil) | Manufacturer data sheet |
| Supplied as | One continuous 100 m coil | – |
| Price per metre | ≈ £11.34 inc VAT | £1,133.91 ÷ 100 m |
| Part number | IP-TPES-9.5X9.5-STD | – |
Materials and compliance
The base is solid TPE (thermoplastic elastomer) and the bulb is TPE foam, so both parts are the same polymer family and the whole strip can be recycled. TPE behaves like rubber but is processed like a plastic; it stays flexible in the cold and resists UV and weather. The manufacturer does not state any food-contact, WRAS, fire or other approvals for this profile, so we do not claim any. If your application needs a certificate, contact us before ordering.
Fitting tips
- Clean the mounting surface with isopropyl alcohol or a degreaser and let it dry. The tape bonds best to clean, dry, smooth metal, painted or plastic surfaces at room temperature.
- Peel back a short length of liner, position the seal and press it down firmly as you go, peeling the liner a little at a time.
- Run the seal round corners in one length where you can; on tight corners, cut a small V-notch out of the base only so the bulb stays continuous.
- Butt the two ends together at the top of the opening so water runs away from the joint.
- Allow the adhesive a day to reach full strength before heavy use or washing down.
Data sheet
Download the technical data sheet (PDF)
Questions
What gap will this seal?
It is designed for a closed-door clearance of 6mm to 8mm between the surface it is stuck to and the surface that closes onto it. Below 6mm the door becomes hard to close; above 8mm the bulb may not touch all the way round.
How do I fit it?
Clean and dry the surface, peel the liner and press the flat base down firmly along its length. No glue, screws or clips are needed. See the fitting tips above.
How do I cut and join it?
Cut it with a sharp utility knife or heavy-duty scissors. For a sealed joint, cut both ends square and butt them tightly together; a drop of cyanoacrylate (superglue) on the base can hold the ends, and placing the joint at the top of the opening keeps water out.
Can it be used outdoors?
Yes. The TPE base and foam bulb are UV and weather resistant and suitable for exterior doors, hatches and enclosures.
What temperature range does it handle?
−50°C to +75°C. It is not meant for oven doors or hot exhausts; for hotter applications choose a silicone seal.
What is it made of, and why two hardnesses?
Both parts are TPE. The 30 Shore D base is firm so the strip stays straight and the tape stays flat; the 15 Shore A foam bulb is very soft so it compresses easily and seals with little closing force.
Will the bulb stay sealed if the frame is slightly uneven?
Yes, within reason. The foam is designed for about 25% working compression, so it can take up small variations along the frame.
Can I buy a shorter length?
This listing is for a full 100m coil. If you need a different length or a quantity of coils, contact us for a quote.
For advice on choosing the right seal, call +44 1282 277786 or email sales@industrial-polymers.co.uk.
Product details
| SKU | IP-TPES-9.5X9.5-STD |
|---|---|
| Weight | 8.38 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:TPE Sponge Seal – Self-Adhesive, Dual Hardness – 9.5mm x 9.5mm for 6–8mm Gaps – 100m Coil