
Rubber & FoamSKU IP-EPDMS-20.8X21.2-10M
EPDM Sponge Boot Seal – 20.8mm x 21.2mm, 6.3mm Panel Slot – 10m to 49m or 50m Coil
Price shown updates with the option you pick.
This EPDM sponge boot seal, 20.8 mm wide x 21.2 mm high, is a one-piece expanded EPDM profile with an angled 6.3 mm slot. The slot pushes over a boot aperture flange or panel edge up to about 6.3 mm thick, and the soft sponge body closes the gap when the lid shuts. It is a correct-section replacement for classic saloon boot lid seals, and it works just as well on hatches, lids and access doors.
Choose a cut length from 10 m to 49 m, supplied as one continuous piece, or a 50 m full coil at the lower coil rate. Held in stock for same-day dispatch.
At a glance
- Size: 20.8 mm W x 21.2 mm H, with a 6.3 mm angled panel slot
- Material: expanded (closed-cell) EPDM sponge, black, 40° Shore OO
- Fixing: push-on over the flange; add a rubber-compatible adhesive in the slot for a permanent fit
- Weather: excellent ozone, UV and weather resistance; passes flexibility at -40 °C
- Weight: 0.15 kg per metre
- Price: £16.23 per metre inc VAT for 10–49 m; 50 m full coil £649.50 inc VAT (£12.99/m)
Technical drawing


Specification
| Property | Value | Test method / basis |
|---|---|---|
| Overall width | 20.8 mm | Manufacturer's drawing (nominal) |
| Overall height | 21.2 mm | Manufacturer's drawing (nominal) |
| Panel slot width | 6.3 mm (fits panels / flanges up to approx. 6.3 mm) | Manufacturer's drawing (nominal) |
| Section type | Solid one-piece sponge with angled open slot; no metal carrier, no adhesive tape | Manufacturer's drawing |
| Dimensional tolerance | BS 3734 Class E3 (sponge is compressible, so sizes are approximate) | BS 3734-1 |
| Material | Expanded EPDM sponge (closed cell) | — |
| Colour | Black | — |
| Hardness | 40° Shore OO | Shore OO durometer |
| Density | 0.5 – 0.9 g/cm³ | Manufacturer's data sheet |
| Weight | 0.15 kg per metre | Manufacturer's data sheet |
| Compression set | 25% max (24 h recovery) per data sheet; 50% (22 h) per product listing | Manufacturer's data (two published values) |
| Water absorption | 5% maximum | Manufacturer's data sheet |
| Oven ageing | ±30% change after 7 days at 70 °C | Manufacturer's data sheet |
| Low-temperature flexibility | Pass at -40 °C | Manufacturer's data sheet |
| Ozone resistance | Excellent | Manufacturer's data sheet |
| Weather resistance | Excellent | Manufacturer's data sheet |
| UV light resistance | Excellent | Manufacturer's data sheet |
| Mould growth resistance | Very good | Manufacturer's data sheet |
| Service temperature | approx. -40 °C to +100 °C (typical for EPDM sponge, not tested on this profile) | Generic material guidance only |
| Tensile strength, elongation, tear | Not published for this profile | — |
| Lengths | 10 m to 49 m in 1 m steps (one piece), or 50 m full coil | — |
Materials and compliance
Expanded EPDM is a closed-cell synthetic rubber sponge chosen for outdoor sealing: it shrugs off ozone, UV and weathering, stays flexible in frost and does not support mould growth. The manufacturer does not state any food-contact, potable-water, flame-retardancy or RoHS/REACH approval for this profile, so none is claimed here. If you need a certificate for a specific approval, ask us before ordering.
Which one do I need?
| Profile | Best for |
|---|---|
| EPDM sponge boot seal 20.8 x 21.2 mm, 6.3 mm slot (this product) | Deep gaps; push-on over thick flanges up to about 6.3 mm |
| EPDM sponge boot seal 16 x 13.5 mm | Smaller gaps; thin flanges (3 mm slot) |
| EPDM sponge boot seal 12 x 17 mm | Self-adhesive twin-hollow seal for flat faces |
| EPDM sponge door seal 15 x 18 mm | Self-adhesive dual-hardness seal for frames without a flange |
How much do I need?
Measure every edge the seal runs along and add about 5% for trimming. Example: a boot opening of 1.2 m x 0.9 m has a perimeter of 2 x (1.2 + 0.9) = 4.2 m, so the 10 m minimum length covers two openings. Order the whole run as one length so there is only one joint. From 41 m upward the 50 m full coil costs less than a cut length.
Fitting tips
- Clean the flange and remove rust, old seal and sealant so the slot seats fully.
- Start at the bottom centre of the opening with the slot facing the flange and press it on with your thumbs, working round in one direction.
- Ease the seal round corners rather than stretching it; stretched sponge shrinks back and opens a gap.
- Leave the end slightly long, then cut square with a sharp knife so the two ends butt under light compression.
- For a permanent fit, run a thin bead of rubber-compatible adhesive inside the slot, and bond the butt joint with a cyanoacrylate rubber glue.
Frequently asked questions
What thickness of panel does this boot seal fit?
The slot is 6.3 mm wide, so it grips flanges and panel edges up to about 6.3 mm thick. On thinner metal it will still sit, but add adhesive in the slot so it cannot pull off.
How do I know this is the right size for my car or hatch?
Cut a short piece of your old seal and compare the end section with the technical drawing above: 20.8 mm across, 21.2 mm high, with one angled slot. Also check that your flange is no thicker than about 6.3 mm and that the closed lid will press a few millimetres into the sponge.
What can it be used for besides a boot lid?
Any push-on edge seal where a soft, deep sponge is needed: tailgates, engine covers, trailer and plant lids, steel cabinet doors, access hatches and enclosure covers.
What is expanded EPDM sponge?
It is EPDM synthetic rubber foamed into tiny closed cells. The cells make it soft (40° Shore OO) so it seals with little closing force, while the EPDM base gives excellent resistance to ozone, UV, rain and frost.
What temperatures will it take?
The manufacturer confirms it stays flexible at -40 °C and passes 7 days ageing at 70 °C. EPDM sponge is typically used up to about +100 °C, but that upper figure has not been tested on this profile.
How do I cut and join it?
Cut with a sharp craft knife or scissors, square across the section. Butt the two ends together under light compression and bond them with a cyanoacrylate glue suited to rubber.
Is it supplied in one piece?
Yes. Every length from 10 m to 49 m is cut as one continuous piece, and the 50 m option is a full uncut coil.
Does it have an adhesive backing?
No. It is a push-on seal held by the slot; use adhesive in the slot if you want it permanently fixed.
Need help choosing a seal? Contact our team, call +44 1282 277786 or email sales@industrial-polymers.co.uk.
Product details
| SKU | IP-EPDMS-20.8X21.2-10M |
|---|---|
| Weight | 3.31 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:EPDM Sponge Boot Seal – 20.8mm x 21.2mm, 6.3mm Panel Slot – 10m to 49m or 50m Coil