
Rubber & FoamSKU IP-EPDMDS-15X18-10M
EPDM Sponge Door Seal – 15mm x 18mm, Dual Hardness, Self-Adhesive – 10m to 39m or 40m Coil
Price shown updates with the option you pick.
A big, soft door seal for larger gaps: a hollow 15 mm sponge EPDM bead standing 18 mm tall on a firm, solid EPDM foot with self-adhesive tape. Cut to one continuous length from 10 m to 39 m, or a full 40 m coil. Peel the liner, press the 13.5 mm foot onto the frame, and the round bead squashes flat as the door closes. The dual-hardness build matters: the solid foot keeps the bead standing upright and stuck down, while the soft sponge tube takes up wide and uneven gaps that a thin strip cannot reach.
At a glance
- Size: Ø15 mm hollow bead, 18 mm overall height, 13.5 mm wide foot (sold as "15 × 18 mm")
- Construction: dual hardness: solid EPDM foot (70° Shore A) with an expanded EPDM sponge bead (40° Shore OO)
- Fixing: self-adhesive tape on the underside of the foot, so no glue, clips or screws
- Seals gaps: best on closed gaps of about 10 to 14 mm (our guidance)
- Outdoors: ozone, weather and UV resistance rated excellent; flexible at -40 °C
- Supplied as: one continuous length, 10 m to 39 m at £22.23 per metre, or a full 40 m coil for £687.06 (£17.18 per metre), all inc VAT
- Stock: held in stock in the UK and dispatched from stock
Typical uses
- Door and tailgate aperture seals on vans, horseboxes, trailers, buses and classic vehicles
- Weather seals on shed, workshop, garage side and garden-room doors with a wide or uneven gap
- Hatch, locker and lid seals on boats, kiosks, plant rooms and machinery covers
- Large-gap seals on electrical enclosures, cabinets and acoustic or dust doors
- Glazing and closure seals where a soft, deep-compressing bulb is needed
- Soft buffer and anti-rattle strip on panels and doors that close onto a stop
Technical drawing

Specifications
| Property | Value | Test method / basis |
|---|---|---|
| Profile type | Hollow round sponge bead on a solid T-shaped foot, self-adhesive underside | Manufacturer's profile drawing |
| Overall height (base to crown) | 18.0 mm | Nominal; tolerance BS 3734 Class E3 |
| Bead outside diameter | Ø15.0 mm (the widest point of the profile) | Nominal; tolerance BS 3734 Class E3 |
| Bead bore | About Ø10.4 mm, giving a sponge wall of about 2.3 mm | Scaled from the manufacturer's drawing; not separately stated |
| Foot (base) width | 13.5 mm on the drawing; 14 mm in the written specification | Manufacturer drawing and product page |
| Foot thickness | 2.5 mm | Manufacturer's profile drawing |
| Neck width (foot to bead) | 6.0 mm | Manufacturer's profile drawing |
| Fixing | Self-adhesive tape on the underside of the foot | Manufacturer product page and drawing |
| Material | Dual hardness EPDM: solid EPDM foot, expanded (sponge) EPDM bead | Manufacturer datasheet |
| Colour | Black | - |
| Hardness, solid foot | 70° Shore A (page); 65 to 75 IRHD (datasheet) | Shore A / IRHD; test standard not stated |
| Hardness, sponge bead | 40° Shore OO | Shore OO scale for soft foams; test standard not stated |
| Sponge density | 0.5 to 0.9 g/cm³ | Manufacturer datasheet; method not stated |
| Weight | 0.10 kg per metre (datasheet); 110 g per metre (product page). About 4.4 kg per 40 m coil | Manufacturer figures |
| Tensile strength, solid foot | 10 MPa | Manufacturer datasheet; method not stated |
| Elongation at break, solid foot | 500% | Manufacturer datasheet; method not stated |
| Tear strength, solid foot | 50 kN/m | Manufacturer datasheet; method not stated |
| Compression set, solid foot | 21% after 22 hours at 70 °C | Manufacturer datasheet |
| Compression set, sponge bead | 25% maximum (24 h recovery) on the datasheet; 50% (22 h) on the product page | Manufacturer figures differ; temperature and standard not stated |
| Heat ageing, solid foot (70 h at 70 °C) | Hardness change 0 IRHD; tensile change +9%; elongation change 0 | Manufacturer datasheet |
| Heat ageing, sponge (7 days at 70 °C) | ±30% change | Manufacturer datasheet; property measured not stated |
| Ozone resistance | Solid foot: no cracks after 72 h at 40 °C, 22 pphm, extended. Sponge: rated excellent | Manufacturer datasheet |
| Weather and UV resistance | Excellent | Manufacturer rating |
| Mould growth resistance | Very good | Manufacturer rating |
| Water absorption | 5% maximum | Manufacturer datasheet; method not stated |
| Low-temperature flexibility | Pass at -40 °C | Manufacturer datasheet |
| Service temperature | No maximum stated for this profile. EPDM sponge is typically used from about -40 °C to +100 °C (typical for EPDM, not tested on this profile) | Ask us if your job runs hot |
| Dimensional tolerance | BS 3734 Class E3 | BS 3734 |
| Supplied as | One continuous length: any whole metre from 10 m to 39 m, or a full 40 m coil | - |
| Price per metre | £22.23/m inc VAT for 10 to 39 m; £17.18/m on the 40 m coil (£687.06) | - |
The manufacturer gives two foot widths (13.5 mm on its drawing, 14 mm in its written spec) and two sponge compression set figures; we show both. Sponge sections are soft and flexible, so treat all sizes as nominal.
Materials and compliance
Two grades of EPDM extruded together. The foot is solid EPDM, chosen for strength and for holding its shape at high and low temperatures. The bead is expanded (closed-cell sponge) EPDM, which compresses easily and recovers to seal against air and water. The manufacturer describes the material as having outstanding resistance to heat, ozone and weathering, good resistance to steam and polar substances, resistance to ketones and dilute acids and alkalis, and good electrical insulating properties. Like all EPDM it is not suited to oils, fuels or most solvents.
The manufacturer does not state any food-contact (FDA, EC 1935/2004), drinking-water (WRAS), REACH, RoHS or fire-rating approval for this profile, so we do not claim any. If your job needs a certified material, ask us before you order.
How it fits

- Measure the closed gap. It must be under 18 mm so the bead is squeezed. About 10 to 14 mm (roughly 20 to 45% squeeze) is a good starting point; this is our guidance, not a manufacturer figure. For gaps under about 9 mm choose a smaller seal (see the table below), or the door will be hard to shut.
- Check the landing. The face you stick to should be flat and at least 14 mm wide. The flat foot goes on the frame; the round bead faces the door. The bead is 15 mm wide, so it overhangs the foot slightly on each side.
- Clean and dry. Wipe the surface with isopropyl alcohol and let it dry. Fit above about 10 °C so the adhesive grabs well.
- Peel and press. Peel the liner a little at a time and press the foot down firmly along its length. Do not stretch it, or it will shrink back and open gaps at the ends.
- Corners and joins. It follows gentle curves. At tight 90° corners, cut and butt or mitre the ends rather than forcing a bend, which kinks the bead. Make joins at the top of a door, where water will not sit; a spot of instant adhesive on the ends gives a fully sealed join.
How much do I need?
Add up every edge you want to seal and allow about 5% for trimming. A standard 2 m × 0.8 m door needs about 5.6 m for three sides and 6.4 m all round; a van rear barn door pair typically takes 8 to 10 m. Every length is cut as one continuous piece, so you can run several doors from one order. From 31 m upwards the full 40 m coil costs less than a cut length.
Which profile do I need?
| Profile | Size (W × H) | Best for |
|---|---|---|
| EPDM sponge door seal (white) | 9 × 7 mm | Small gaps on interior doors |
| EPDM sponge D section | 10 × 8 mm | Medium gaps, single hollow D bulb |
| EPDM sponge D section | 12 × 10 mm | Medium gaps, wider D bulb |
| EPDM sponge door seal, figure-8 | 10 × 15 mm | Closed gaps of about 8 to 11 mm on a narrow 10 mm landing |
| EPDM sponge door seal, dual hardness (this item) | 15 × 18 mm | Closed gaps of about 10 to 14 mm, wide or uneven frames |
| EPDM sponge door seal, D profile | 16 × 14 mm | Wide D bulb for large, flat landings |
| EPDM sponge boot seal | 16 × 13.5 mm | Push-on over a panel edge instead of an adhesive foot |
| EPDM sponge T seal | 19 × 16.5 mm | Larger section for wider gaps |
Questions
What gap will it seal?
Any closed gap under its 18 mm height. Aim for about 10 to 14 mm. For smaller gaps the door will be stiff to close, so choose the 10 × 15 mm or a D section instead.
What does "15 × 18 mm" mean?
The bead is 15 mm across and the whole seal is 18 mm tall from the bottom of the foot to the top of the bead. The foot is 13.5 to 14 mm wide.
Is it self-adhesive?
Yes. The underside of the foot carries adhesive tape with a peel-off liner. It sticks to clean, dry painted metal, bare metal, wood, glass, most rigid plastics and rubber.
Which way up does it go?
The flat foot with the adhesive goes on the frame or flange. The round sponge bead faces the closing door.
Why two hardnesses?
A soft bead on its own would roll over and peel off; a hard one would make the door difficult to shut. The firm foot holds the seal upright and gives the adhesive a stiff, flat surface, while the soft bead does the sealing.
How do I cut and join it?
A sharp craft knife or scissors gives a clean square end. Butt the ends tightly; for a fully sealed join, glue the ends together with instant adhesive.
Will it go round corners?
It follows gentle curves and radiused frames. For sharp 90° corners, cut and butt or mitre the strip so the bead does not kink or lift.
What temperatures can it take?
The manufacturer states it passes a -40 °C flexibility test and the solid foot is heat-aged at 70 °C with no change in hardness, but no maximum is given for this profile. EPDM sponge is typically used up to about +100 °C (typical for the material, not tested on this profile). The adhesive may soften first, so ask us about hot jobs.
Can I use it outdoors?
Yes. Ozone, weather and UV resistance are rated excellent, mould resistance is very good, and water absorption is 5% maximum.
Will it stand up to oil or fuel?
No. EPDM handles water, steam, weather and dilute acids and alkalis well, but swells in oils, fuels and most solvents.
How is it supplied?
As one continuous piece in the length you choose, from 10 m to 39 m, or as a full 40 m coil. The coil is cheaper per metre, and from 31 m upwards it is cheaper outright.
Is it food-safe or WRAS approved?
No approvals are stated for this profile, so do not use it where certified food-contact or drinking-water material is required.
Delivery and help
Held in stock and dispatched from the UK. Trade and quantity orders welcome. Not sure it is the right profile? Call +44 1282 277786 or email sales@industrial-polymers.co.uk and we will check it for you.
Product details
| SKU | IP-EPDMDS-15X18-10M |
|---|---|
| Weight | 2.43 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:EPDM Sponge Door Seal – 15mm x 18mm, Dual Hardness, Self-Adhesive – 10m to 39m or 40m Coil