
Rubber & FoamSKU IP-EPDMS-16X13.5-06M
EPDM Sponge Boot Seal – 16mm x 13.5mm with 3mm Side Slot – 6m to 50m Lengths
Price shown updates with the option you pick.
A soft, black EPDM sponge seal 16 mm wide and 13.5 mm high, with a 3 mm wide, 9 mm deep slot along one side. Push the slot onto a lip, flange or panel edge and the rounded sponge top forms an air- and water-tight cushion for a closing boot lid, hatch, door or cover. It is a reproduction of a classic-car boot-lid seal profile and works equally well on enclosures, cabinets and access panels.
Choose any length from 6 m to 49 m, supplied as one continuous piece, or the full 50 m coil at a lower rate per metre.
At a glance
- Size: 16 mm wide x 13.5 mm high, 14 mm across the base
- Slot: 3 mm wide x 9 mm deep, opening to one side; takes an edge up to about 3 mm thick
- Material: expanded EPDM sponge, black, 40° Shore OO
- Weather: ozone, weather and UV resistance rated excellent; flexible at −40 °C
- Lengths: 6 m to 49 m in 1 m steps, or a 50 m coil; about 0.1 kg per metre
- In stock in our UK warehouse
Technical drawing

Specifications
| Property | Value | Test method / source |
|---|---|---|
| Overall width | 16 mm | Manufacturer's drawing |
| Overall height | 13.5 mm | Manufacturer's drawing |
| Base width (flat underside) | 14 mm | Manufacturer's drawing |
| Slot (channel) width | 3 mm | Manufacturer's drawing |
| Slot depth | 9 mm | Manufacturer's product data |
| Edge thickness it takes | Up to about 3 mm | Derived from the 3 mm slot |
| Dimensional tolerance | BS 3734 Class E3 (sponge, so sizes are approximate) | BS 3734 |
| Material | Expanded EPDM sponge | Manufacturer's data sheet |
| Colour | Black | — |
| Hardness | 40° Shore OO | Shore OO durometer |
| Density | 0.5 – 0.9 g/cm³ | Manufacturer's data sheet |
| Water absorption | 5% maximum | Manufacturer's data sheet |
| Compression set | 25% maximum after 24 h recovery (data sheet); 50% at 22 h (product page) | Manufacturer's data; the two sources differ |
| Oven ageing | ±30% change after 7 days at 70 °C | Manufacturer's data sheet |
| Low-temperature flexibility | Pass at −40 °C | Manufacturer's data sheet |
| Ozone resistance | Excellent | Manufacturer's data sheet |
| Weather resistance | Excellent | Manufacturer's data sheet |
| UV light resistance | Excellent | Manufacturer's data sheet |
| Mould growth resistance | Very good | Manufacturer's data sheet |
| Upper service temperature | About +100 °C (typical for EPDM sponge, not tested on this profile) | General material guidance |
| Tensile strength, elongation, tear | Not stated by the manufacturer for this profile | — |
| Weight | About 0.10 kg per metre | Manufacturer's data sheet |
| Lengths | 6 m to 49 m (one piece) or 50 m full coil | — |
Materials and compliance
Made from expanded EPDM (ethylene propylene diene) sponge rubber, which is naturally resistant to ozone, weathering and sunlight. The manufacturer does not state any food-contact, water (WRAS), fire, REACH or RoHS approval for this profile, so we do not claim one. If you need a certified material, ask us before ordering.
Price per metre
| Length | Price inc VAT | Per metre |
|---|---|---|
| 6 m to 49 m | £91.80 to £749.70 | £15.30 |
| 50 m full coil | £612.00 | £12.24 |
Tip: 40 m costs the same as the 50 m coil, so if you need 40 m or more, choose the full coil.
Typical uses
- Boot-lid, tailgate and bonnet aperture seals on classic and specialist vehicles
- Hatch, access-panel and inspection-cover weather seals
- Electrical cabinet and enclosure door seals
- Edge cushions and gap fillers on glazing, joinery and closures
- Light anti-vibration and anti-rattle strips
How to fit
- Clean the lip or flange and remove old seal and adhesive.
- Start at a low, hidden point, such as the bottom centre of the opening.
- Push the slot onto the edge by hand, working along a little at a time; do not stretch the sponge.
- Ease it round corners rather than cutting them.
- Cut the end square with a sharp knife, leaving a few millimetres extra so the ends butt tightly.
- For extra hold, or to join the ends, use a rubber-compatible contact adhesive or cyanoacrylate.
How much do I need?
Measure round the whole opening along the edge the seal will sit on, then add about 5% for trimming. Example: a boot opening of 3.8 m needs about 4 m, so the 6 m minimum length leaves plenty spare.
Which profile do I need?
| Your situation | Suggested seal |
|---|---|
| Lip or flange up to about 3 mm thick | This 16 x 13.5 mm boot seal |
| Thicker flange, about 6 mm | 20.8 x 21.2 mm sponge boot seal, 6.3 mm channel |
| Flat face, no flange, stick-on fixing | 12 x 17 mm self-adhesive twin-hollow boot seal |
Frequently asked questions
How does this seal fit?
It push-fits: the 3 mm side slot slides over a lip, flange or panel edge up to about 3 mm thick and grips it along its 9 mm depth. Adhesive is optional.
How do I check it is the right size?
Measure the thickness of the edge it will sit on (up to 3 mm) and the gap between that edge and the closing face. The seal stands 13.5 mm tall and should be squeezed by roughly a quarter to a third when shut.
Can I use it outdoors?
Yes. The manufacturer rates its ozone, weather and UV resistance as excellent, and it passes a flexibility test at −40 °C.
What temperatures can it take?
It stays flexible down to −40 °C (manufacturer's test). EPDM sponge typically copes with about +100 °C continuous; that upper figure is typical for the material, not a test on this profile.
How do I cut and join it?
Cut with a sharp knife or scissors in one clean stroke. Butt the ends together and bond them with cyanoacrylate or a rubber-compatible contact adhesive.
Is it the same material as a solid rubber seal?
No. It is expanded (sponge) EPDM at 0.5–0.9 g/cm³ and 40° Shore OO, much softer than solid rubber, so it compresses easily against uneven surfaces with little closing force.
Will it suit my classic car?
The profile reproduces a period boot-lid seal for 1950s and 1960s sports cars. Compare the drawing with your old seal and the flange on your car before ordering.
Is it in stock?
Yes, it is held in stock and cut to your chosen length.
Complete your project
- EPDM sponge door seal, 10 x 15 mm self-adhesive figure-8
- EPDM sponge T seal, 19 x 16.5 mm
- EPDM sponge wedge seal, 12 x 6 mm
Not sure which profile you need? Send us a photo or the old seal's measurements via our contact page.
Product details
| SKU | IP-EPDMS-16X13.5-06M |
|---|---|
| Weight | 1.32 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:EPDM Sponge Boot Seal – 16mm x 13.5mm with 3mm Side Slot – 6m to 50m Lengths