
Rubber & FoamSKU IP-EPDM-9X14-15M
EPDM Sponge Caravan Seal – 9mm x 14mm Dual Hardness – Cut Length or 50m Coil
Price shown updates with the option you pick.
A black dual-hardness EPDM caravan seal, 9 mm wide by 14 mm high. A soft 10 mm hollow sponge bulb sits on a solid rubber T-foot with a 5 mm base, and the foot slides or pushes into the slotted channel found around caravan and motorhome doors, windows, lockers and shower cubicles. When the door closes, the bulb compresses and fills uneven gaps to keep out draughts and rain. It is supplied as one continuous length, 15 m to 49 m, or as a full 50 m coil, and is held in stock for dispatch.
At a glance
- Size: 9 mm wide x 14 mm high overall: 10 mm sponge bulb on a 4 mm foot with a 5 mm base
- Two hardnesses in one strip: 70° Shore A solid EPDM foot grips the slot; 40° Shore OO sponge bulb seals
- Weatherproof: ozone, weather and UV resistance rated excellent; flexible at -40 °C
- Low water uptake: sponge absorbs 5% maximum
- Non-marking, cuts cleanly with a sharp knife
- Lengths: any whole metre from 15 m to 49 m in one piece, or a 50 m coil at the lowest price per metre
Will it fit my frame?
This seal is for frames with a slot: a narrow mouth with a wider chamber behind it that holds the T-foot. The foot is 5 mm wide, so the chamber needs to be at least 5 mm wide. It is not self-adhesive and will not stay on a flat surface without a slot. If your old seal has a similar round bulb on a T-shaped foot, measure its overall height and width and compare them with the drawing below. If you are unsure, email a photo of the cut end next to a ruler to sales@industrial-polymers.co.uk and we will check it for you.
Technical drawing

Specifications
| Property | Value | Test method / basis |
|---|---|---|
| Profile type | Hollow sponge bulb on a solid T-foot (push-in / slide-in seal) | Manufacturer's profile drawing |
| Overall width (across the bulb) | 9.0 mm (data sheet drawing: 8.5 mm) | Nominal; tolerance BS 3734 Class E3. The product page and data sheet differ |
| Overall height (foot to top of bulb) | 14.0 mm (data sheet drawing: 14.5 mm) | Nominal; tolerance BS 3734 Class E3. The product page and data sheet differ |
| Sponge bulb height | 10.0 mm | Manufacturer's profile drawing |
| Foot height below the bulb | 4.0 mm | Worked out from 14 mm overall less 10 mm bulb; not separately stated |
| Base (T-foot) width | 5.0 mm | Manufacturer's profile drawing |
| Stem width, flange thickness, bulb wall, core size | Not stated | Shown indicatively on our drawing only. Send us your slot size if the fit is tight |
| Fits | A slotted groove in a door, window, locker or shower frame with a chamber at least 5 mm wide behind a narrower mouth | From the 5 mm foot width; check your frame |
| Material: foot | Solid (dense) EPDM rubber | Manufacturer data sheet |
| Material: bulb | Expanded (sponge) EPDM | Manufacturer data sheet |
| Colour | Black | - |
| Hardness: solid foot | 70° Shore A (data sheet: 65–75 IRHD) | Shore A / IRHD; test standard not stated |
| Hardness: sponge bulb | 40° Shore OO | Shore OO durometer scale (for soft foams); test standard not stated |
| Tensile strength (solid EPDM) | 10 MPa | Manufacturer data sheet; method not stated |
| Elongation at break (solid EPDM) | 500% | Manufacturer data sheet; method not stated |
| Tear strength (solid EPDM) | 50 kN/m | Manufacturer data sheet; method not stated |
| Compression set (solid EPDM) | 21% after 22 h at 70 °C | Manufacturer data sheet; standard not stated |
| Compression set (sponge bulb) | 25% maximum (data sheet, 24 h recovery) · 50% (product page, 22 h) | Manufacturer figures; temperature and standard not stated. The two sources differ, so plan on the higher figure |
| Heat ageing (solid EPDM), 70 h at 70 °C | Hardness change 0 IRHD · tensile change +9% · elongation change 0 | Manufacturer data sheet |
| Heat ageing (sponge), 7 days at 70 °C | ±30% change | Manufacturer data sheet; property measured not stated |
| Ozone resistance (solid EPDM) | No cracks after 72 h at 40 °C, 22 pphm, extended | Manufacturer data sheet |
| Sponge density | 0.5 to 0.9 g/cm³ | Manufacturer data sheet; method not stated |
| Water absorption (sponge) | 5% maximum | Manufacturer data sheet; method not stated |
| Low-temperature flexibility | Pass at -40 °C | Manufacturer data sheet |
| Ozone, weather and UV resistance (sponge) | Excellent | Manufacturer rating |
| Mould growth resistance | Very good | Manufacturer rating |
| Service temperature range | Not stated for this profile. Typical for EPDM: about -40 °C to +100 °C (typical for EPDM, not tested on this profile) | Tested points stated: flexible at -40 °C, aged at +70 °C |
| Weight | 116 g/m (product page) · 50 g/m (data sheet) | Manufacturer figures; the two sources differ. We ship on the higher figure |
| Dimensional tolerance | BS 3734 Class E3 (extruded sponge) | BS 3734 |
| Supplied length | One continuous length, 15 m to 49 m in 1 m steps, or a full 50 m coil | - |
| Price per metre | £12.77/m inc VAT for cut lengths · £9.90/m on the 50 m coil (£495.00) | - |
Materials and compliance
Solid EPDM foot co-extruded with an expanded (sponge) EPDM bulb. The manufacturer describes it as non-marking, air and watertight, and resistant to heat, ozone, weather, steam, ketones and dilute acids and alkalis.
The manufacturer does not state any food-contact (FDA, EC 1935/2004), drinking-water (WRAS), REACH, RoHS or fire-rating approval for this profile, so we do not claim any. If your application needs a certified material, ask us before you order.
Choosing a length
Cut lengths are £12.77 per metre inc VAT (15 m = £191.58, 20 m = £255.42, 30 m = £383.13). The full 50 m coil is £495.00, only £9.90 per metre, so if you need 39 m or more the coil costs less than the cut length. Measure the full run of each slot, add about 5% for trimming and for easing the seal round corners, and round up to the next metre. A typical 1.8 m x 0.6 m caravan entrance door has a 4.8 m perimeter, so three doors or lockers of that size need about 15 m.
How to fit it

- Pull out the old seal and clean the slot of dirt, old sealant and grit.
- Start at the bottom of the frame, away from the hinge side, and feed the T-foot into the end of the slot or press it in with your thumbs. A little soapy water helps it slide.
- Work round the frame without stretching the seal: stretched EPDM shortens back and leaves gaps at the joints.
- At corners, ease the seal round in a gentle curve rather than cutting it, so the bulb does not kink.
- Leave 5 mm extra at the end, then cut square with a sharp knife and push the two ends tightly together. A spot of rubber-compatible adhesive on the butt joint stops it opening up.
- Close the door and check that it shuts without forcing: with the bulb about a third compressed, the door should close easily and seal along its full length.
Frequently asked questions
Is this the right seal for my caravan door?
It suits doors, windows and lockers whose frames have a slot that takes a T-shaped foot about 5 mm wide. Compare your old seal with the drawing: if it is a round sponge bulb about 9 mm wide and 14 mm tall on a T-foot, this is the match. Many different seals are used across makes and years, so check the cut end before ordering.
Do I need glue to fit it?
No. The solid foot is held by the slot. Adhesive is only worth using on the butt joint where the two ends meet.
How much does the bulb compress, and what gap does it seal?
The sponge bulb is 10 mm tall and is designed to be squashed. As a guide, it seals best with the door closing to leave about 6 to 8 mm between the door and the frame face, so the bulb is compressed by about a third. Much tighter than that and the door may be hard to shut.
Can I use it outdoors and in winter?
Yes. EPDM is the standard outdoor seal rubber: the manufacturer rates its ozone, weather and UV resistance as excellent and it passes a flexibility test at -40 °C.
Can I use it in a shower or washroom?
Yes, the manufacturer lists shower seals as a use. The sponge absorbs no more than 5% water and mould growth resistance is rated very good. It is not approved for food or drinking-water contact.
How do I cut and join it?
Cut square with a sharp knife or scissors. Push the ends together tightly when you finish a run; a small amount of rubber-compatible adhesive keeps the joint closed. Ease it round corners rather than mitring.
Why are the sizes on the data sheet slightly different?
The manufacturer's product page says 9 x 14 mm and its data sheet drawing says 8.5 x 14.5 mm. Both are within the normal tolerance for soft sponge extrusions (BS 3734 Class E3), and we show both so you can judge the fit.
Will it come in one piece?
Yes. Every length from 15 m to 49 m is cut as one continuous strip, and the 50 m option is a full unbroken coil.
Data sheet
Download the technical data sheet (PDF) with the drawing, full specification and compliance notes.
Complete your project
- Silicone Sponge Rubber Strip – 3mm Thick – 25m Roll
- Self-Grip EPDM Top Seal – 6mm x 15mm – Sponge Bulb, Fits 1.6mm Panels
- TPE U Channel – 12mm x 17.5mm for 4.5mm Panels – 50m Coil
Need help choosing the right profile? Call +44 1282 277786, email sales@industrial-polymers.co.uk or contact our team.
Product details
| SKU | IP-EPDM-9X14-15M |
|---|---|
| Weight | 4.06 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:EPDM Sponge Caravan Seal – 9mm x 14mm Dual Hardness – Cut Length or 50m Coil