
Rubber & FoamSKU IP-SGTS-6X15-17M
Self-Grip EPDM Top Seal – 6mm x 15mm – Sponge Bulb, Fits 1.6mm Panels – 17m to 50m
Price shown updates with the option you pick.
A push-on edge seal for 1.6 mm panels: a solid EPDM rubber clip with a steel carrier inside, topped by a soft sponge EPDM bulb. The clip grips the edge with no glue. When a door, hatch, lid or window closes onto the bulb, the bulb squashes and makes a watertight, draught-proof line. The section is 6 mm wide and 15 mm high, with a 7.5 mm deep grip. Choose one continuous length from 17 m to 49 m, or a full 50 m coil. It is in stock in the UK for same-day dispatch.
At a glance
- Fits: sheet, panel and flange edges 1.6 mm thick, at least 7.5 mm deep
- Size: 6 mm wide × 15 mm high; 2 mm opening; 7.5 mm grip depth
- Construction: solid EPDM grip (80 ± 5° Shore A) over a U-shaped steel carrier, with a hollow sponge EPDM sealing bulb on top
- Seals best when the closed gap squeezes the bulb by 30–40 %
- Working temperature: −40 °C to +80 °C; ozone-tested EPDM for outdoor use
- Lengths: 17 m to 49 m in 1 m steps, or a full 50 m coil. The 50 m coil costs less than any length from 39 m up.
Technical drawing

How it fits

- Clean the edge and file off any burrs.
- Start at one end and press the seal onto the edge with your thumbs. Tap it fully home with a rubber or plastic mallet, working along the run.
- Ease it round corners rather than stretching it. Stretched rubber shrinks back later and leaves gaps.
- Cut it to length with heavy-duty scissors or snips and butt the two ends tightly together.
Typical uses
- Window, side-glass and roof-panel edges on cars, vans, buses and trains
- Doors, hatches and inspection covers on machinery and enclosures
- Marine lockers, hatches and equipment covers
- Interior side panels, cabinet doors and furniture edges
Specifications
| Property | Value | Test method |
|---|---|---|
| Dimensions and supply | ||
| Overall width | 6 mm | Nominal |
| Overall height | 15 mm | Nominal |
| Grip depth (inside channel) | 7.5 mm | Nominal |
| Channel opening | 2 mm | Nominal |
| Panel thickness it fits | 1.6 mm | - |
| Dimensional tolerance | Not stated by the manufacturer; ask us before ordering for a tight fit | - |
| Colour | Black | - |
| Lengths | 17 m to 49 m in one piece (1 m steps), or a 50 m coil | - |
| Whole profile | ||
| Construction | Solid EPDM grip, sponge EPDM bulb, steel carrier | - |
| Operating temperature | −40 °C to +80 °C | - |
| Recommended bulb compression | 30–40 %; 40 % maximum in normal service (never above 50 %) | - |
| Compression set (7 days at 70 °C) | 50 % max | ASTM D1056 |
| Migration stain on painted finishes | Satisfactory | ASTM D925 |
| Contact stain on painted finishes | Satisfactory | ASTM D925 |
| Colour fastness | Satisfactory | ASTM D750 |
| Solid EPDM grip section | ||
| Hardness | 80 ± 5° Shore A (the product page quotes 67–82° across the whole profile) | ASTM D2240 |
| Tensile strength | 80 kg/cm² min (about 7.8 MPa) | ASTM D412 |
| Tear resistance | 3 kg/mm min (about 29 kN/m) | ASTM D624 |
| Brittle point | −40 °C | ASTM D746 |
| Compression set | 40 % max | ASTM D395 Type B |
| After air ageing 70 h at 70 °C: hardness change | +2° Shore A | - |
| After air ageing 70 h at 70 °C: tensile change | +15 % | - |
| Ozone resistance (70 h at 50 °C, 50 pphm, 20 % stretch) | No cracks | ASTM D1149 |
| Elongation at break | Not stated by the manufacturer | - |
| Sponge EPDM sealing bulb | ||
| Density (indicative) | 550–600 kg/m³ (0.55–0.60 g/cm³)* | - |
| Tensile strength | 7–10 kg/cm² (about 0.7–1.0 MPa) | ASTM D412 |
| Tear resistance | 0.6 / 0.8 kg/mm (about 5.9 / 7.8 kN/m) | ASTM D624 |
| Water absorption (22 h at 23 °C) | 1.2 % max | ASTM D1056 |
| Brittle point | −40 °C | ASTM D746 |
| Ozone resistance (70 h at 50 °C, 50 pphm, 50 % stretch) | No cracks | ASTM D1149 |
| Steel carrier | ||
| Grade | Fe 50 to UNI 5961-67 | - |
| Hardness | 80–90 HRB (Rockwell B) | - |
| Tensile strength | 50 kg/mm² min (about 490 MPa) | - |
All values are from the manufacturer's data for this profile. Metric conversions in brackets are ours. *The manufacturer's sheet prints the sponge density unit as g/cm³; 550–600 can only be kg/m³ for a sponge, so we show it that way.
Materials and compliance
The grip is solid EPDM rubber and the bulb is sponge EPDM, moulded together over a U-shaped Fe 50 steel carrier. EPDM is chosen for outdoor seals because it shrugs off sunlight, ozone, rain and frost. Both rubber parts of this profile have passed the ASTM D1149 ozone test with no cracking, and the profile passes the ASTM D925 staining tests, both rated satisfactory, so it is suited to painted panels.
The manufacturer states no food-contact, fire-rating, WRAS or other approvals for this profile, so we do not claim any. If you need a certified material, call or email us and we will suggest a seal that has it.
How much do I need?
Measure the full length of edge to be sealed and add 5–10 % for corners and trimming. Each length is supplied as one continuous piece, so a whole door or hatch can be sealed with only one joint. If you need more than about 39 m, the 50 m coil is the cheaper choice.
Frequently asked questions
Do I need glue or clips to fit it?
No. The steel carrier and the gripping barb inside the channel clamp both faces of the edge, so it stays on by grip alone. On edges that see heavy vibration, a few dots of contact adhesive in the channel add extra hold.
What panel thickness does it fit?
It is made for a 1.6 mm edge, which is common sheet steel and aluminium gauge. Edges a little thinner or thicker may fit, but the grip gets weaker or the seal gets harder to push on. The edge needs to be at least 7.5 mm deep so the channel can seat fully. For other thicknesses, ask us for a matching profile.
How big a gap should the bulb seal?
Size the gap so the closed door or lid squeezes the bulb by 30–40 %. Squeezing it more than 40 % in service makes the sponge take a permanent set and stop springing back, and it must never go past 50 %.
Will it go round corners?
Yes. The steel carrier lets it bend round curves and corners by hand. Ease it round tight corners rather than pulling it, and on very tight 90° corners cut a small V out of the grip section (not the bulb) so it lies flat.
How do I cut and join it?
Cut it with heavy-duty scissors, tin snips or a sharp knife and side cutters for the steel. Cut square and butt the two ends tightly together. A drop of rubber-compatible instant adhesive on the end faces makes the joint neater and keeps water out.
Can it be used outdoors and in the cold?
Yes. The EPDM is rated from −40 °C to +80 °C and has passed the ozone test with no cracks, so it suits vehicles, boats and outdoor enclosures all year round.
Can I take it off and refit it?
Yes. It pulls off by hand and can be refitted. Grip strength drops a little each time the carrier is opened up, so do not refit it more often than you need to.
Is it in stock?
Yes. All lengths and the 50 m coil are held in stock in the UK and go out the same day on orders placed before the cut-off.
Complete your project
- Self-Grip PVC Edge Trim – 6.5mm x 9.5mm – 50m Coil
- Neoprene U Channel – 6mm x 13.5mm Profile – 1.6mm Panel – Cut Lengths
- EPDM Rubber U Channel – 6mm x 8.5mm – Per Length
Not sure it is the right profile? Call +44 1282 277786 or email sales@industrial-polymers.co.uk with your edge thickness and gap, and we will check it for you.
Product details
| SKU | IP-SGTS-6X15-17M |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Self-Grip EPDM Top Seal – 6mm x 15mm – Sponge Bulb, Fits 1.6mm Panels – 17m to 50m