
Rubber & FoamSKU IP-EPDMS-10X7-STD
EPDM Sponge P-Section Seal – 10mm x 7mm, Self-Adhesive, Black – 100m Coil
A small, soft P-section seal in black EPDM sponge: 10 mm wide, 7 mm high, with a hollow bulb and a self-adhesive back, on a 100 m coil. Peel the liner, press it onto the frame, and the hollow 7 mm bulb squashes down when a door, lid or hatch closes on it. The short 3 mm flange beside the bulb adds bonding area and helps it sit straight. It gives a quiet, air- and water-resistant seal on cabinets, enclosures, windows and vehicle hatches.
At a glance
- Size: 10 mm wide × 7 mm high; 7 mm hollow D-bulb with a 4 mm core, plus a 3 × 1.5 mm flange
- Fixing: self-adhesive tape across the full 10 mm base, so no glue or fixings
- Material: expanded (sponge) EPDM, very soft at 40° Shore OO
- Seals gaps: best on closed gaps of about 4 to 5.5 mm (our guidance)
- Outdoors: ozone, weather and UV resistance rated excellent; flexible at -40 °C
- Supplied as: one continuous 100 m coil, £3.33 per metre inc VAT
- Stock: held in stock in the UK and dispatched from stock
Typical uses
- Door seals on electrical enclosures, control cabinets and steel lockers
- Draught and weather seals on windows, sheds, garden rooms and loft hatches
- Hatch, locker and tailgate seals on vans, trailers, caravans, horseboxes and boats
- Glazing and closure seals on panels, covers and machine guards
- Dust and splash seals on electronics housings and instrument boxes
- Soft anti-rattle and impact strip between metal, wood and plastic parts
Technical drawing

Specifications
| Property | Value | Test method / basis |
|---|---|---|
| Profile type | Hollow P-section: D-shaped bulb with a side flange, flat self-adhesive base | Manufacturer's profile drawing |
| Overall width (across the base) | 10.0 mm | Nominal; tolerance BS 3734 Class E3 |
| Overall height (base to top of bulb) | 7.0 mm | Nominal; tolerance BS 3734 Class E3 |
| Bulb width | 7.0 mm (round crown, R 3.5 mm) | Manufacturer's profile drawing |
| Hollow core width | 4.0 mm | Manufacturer's profile drawing |
| Hollow core height / wall thickness | About 4 mm / about 1.5 mm | Scaled from the manufacturer's drawing; not separately stated |
| Flange (tail) length | 3.0 mm beyond the bulb | Manufacturer's profile drawing |
| Flange thickness | 1.5 mm | Manufacturer's profile drawing |
| Fixing | Self-adhesive tape on the full 10 mm base | Manufacturer product page and datasheet |
| Material | Expanded (sponge) EPDM | Manufacturer datasheet |
| Colour | Black | - |
| Hardness | 40° Shore OO | Shore OO durometer scale (for soft foams); test standard not stated |
| Density | 0.5 to 0.9 g/cm³ | Manufacturer datasheet; method not stated |
| Weight | 13 g/m (product page) to 20 g/m (datasheet): about 1.3 to 2 kg per 100 m coil | Manufacturer figures differ; both shown |
| Service temperature | Not stated for this profile. EPDM sponge is typically used from about -40 °C to +100 °C (typical for EPDM sponge, not tested on this profile) | Ask us if your job runs hot |
| Low-temperature flexibility | Pass at -40 °C | Manufacturer datasheet |
| Heat ageing | ±30% change after 7 days at 70 °C | Manufacturer datasheet; property measured not stated |
| Compression set | 25% maximum (24 h recovery) on the datasheet; 50% (22 h) on the product page | Manufacturer figures differ; test temperature and standard not stated |
| Water absorption | 5% maximum | Manufacturer datasheet; method not stated |
| Ozone resistance | Excellent | Manufacturer rating |
| Weather resistance | Excellent | Manufacturer rating |
| UV light resistance | Excellent | Manufacturer rating |
| Mould growth resistance | Very good | Manufacturer rating |
| Tensile strength, elongation at break, tear strength | Not stated for this profile | Ask us if you need them |
| Dimensional tolerance | BS 3734 Class E3 (extruded sponge) | BS 3734 |
| Supplied as | One 100 m coil | - |
| Price per metre | £3.33/m inc VAT (£333.00 per 100 m coil) | - |
The manufacturer's own figures differ in places: its product page and catalogue give 10 × 7 mm, while its PDF data sheet drawing shows 9 × 6 mm with a 2.5 mm flange; weight is 13 g/m on the page and 20 g/m on the data sheet; compression set is 50% on the page and 25% maximum on the data sheet. We show both. Sponge sections are soft and flexible, so treat all sizes as nominal.
Materials and compliance
Expanded (closed-cell sponge) EPDM. The manufacturer describes it as air and water resistant, with outstanding resistance to heat, ozone, weathering and steam, resistance to ketones and dilute acids and alkalis, and good electrical insulating properties. Like all EPDM it is not suited to oils, fuels or most solvents.
The manufacturer does not state any food-contact (FDA, EC 1935/2004), drinking-water (WRAS), REACH, RoHS or fire-rating approval for this profile, so we do not claim any. If your job needs a certified material, ask us before you order.
How it fits

- Measure the closed gap. It must be under 7 mm so the bulb is squeezed. About 4 to 5.5 mm (20 to 40% squeeze) is a good starting point; this is our guidance, not a manufacturer figure.
- Check the landing. The face you stick to should be flat and at least 10 mm wide. The flange can face into or out of the opening.
- Clean and dry. Wipe the surface with isopropyl alcohol and let it dry. Fit above about 10 °C so the adhesive grabs well.
- Peel and press. Peel the liner a little at a time and press the strip down firmly along its length. Do not stretch it, or it will shrink back and open gaps at the ends.
- Corners and joins. It bends round gentle corners. For tight 90° corners, notch the base or cut and butt the ends. Butt joins tightly; a spot of instant adhesive on the ends gives a fully sealed join.
How much do I need?
Add up every edge you want to seal and allow about 5% for trimming. A 600 × 400 mm enclosure door takes 2 m, so one 100 m coil does around 45 to 50 doors; a standard 1200 × 1050 mm casement window frame takes about 4.5 m.

Which profile do I need?
| Profile | Size (W × H) | Best for |
|---|---|---|
| EPDM sponge P-section (this item) | 10 × 7 mm | Closed gaps of about 4 to 5.5 mm, hollow bulb, self-adhesive |
| EPDM sponge crown strip | 10 × 5 mm | Smaller gaps, low profile, self-adhesive |
| EPDM sponge door seal (white) | 9 × 7 mm | Similar gap, white wrap-over lip for interior doors |
| EPDM sponge D section | 8 × 10 mm | Larger gaps (6 to 8 mm), hollow, self-adhesive |
| TPE P profile | 16 mm flange × 6 mm bulb | Firmer solid-skin TPE with a wider fixing flange |
Data sheet
Download the technical data sheet (PDF): drawing, full specification and compliance
Questions
What gap will it seal?
Any closed gap under its 7 mm height. Aim for about 4 to 5.5 mm. For 3 to 4 mm gaps choose the 10 × 5 mm crown strip; for 6 to 8 mm use the 8 × 10 mm D section.
Is it self-adhesive?
Yes. The full 10 mm base carries adhesive tape with a peel-off liner. It sticks to clean, dry metal, painted surfaces, wood, glass, most rigid plastics and rubber.
Which way round does it go?
The flat base goes on the frame or door stop and the bulb faces the closing door or lid. The 3 mm flange can face either way; put it on the side with the most landing width.
How do I cut and join it?
Scissors or a sharp craft knife gives a clean square end. Butt the ends tightly; for a fully sealed join, glue the ends together with instant adhesive.
Will it go round corners?
Yes, it follows gentle curves easily. For sharp 90° corners, cut a small V-notch in the base, or cut and butt the strip, so it does not lift.
What temperatures can it take?
The manufacturer states it passes a -40 °C flexibility test but gives no maximum for this profile. EPDM sponge is typically used up to about +100 °C (typical for the material, not tested on this profile). The adhesive may soften before the rubber does, so ask us about hot jobs.
Can I use it outdoors?
Yes. The manufacturer rates its ozone, weather and UV resistance as excellent and mould resistance as very good, and water absorption is 5% maximum.
Will it stand up to oil or fuel?
No. EPDM handles water, steam, weather and dilute acids and alkalis well, but swells in oils, fuels and most solvents. Ask us for a neoprene or nitrile alternative.
Can I buy it by the metre?
This listing is a full 100 m coil, which works out at £3.33 per metre inc VAT. Need a shorter length? Call or email and we will quote.
Is it food-safe or WRAS approved?
No approvals are stated for this profile, so do not use it where certified food-contact or drinking-water material is required.
Delivery and help
Held in stock and dispatched from the UK. Trade and quantity orders welcome. Not sure it is the right profile? Call +44 1282 277786 or email sales@industrial-polymers.co.uk and we will check it for you.
Product details
| SKU | IP-EPDMS-10X7-STD |
|---|---|
| Weight | 4.41 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:EPDM Sponge P-Section Seal – 10mm x 7mm, Self-Adhesive, Black – 100m Coil