
Rubber & FoamSKU IP-EPDMS-10X15-10M
EPDM Sponge Door Seal – 10mm x 15mm Figure-8 Double Hollow, Self-Adhesive, Black – 10m to 50m
Price shown updates with the option you pick.
A soft, deep-compressing door seal in black EPDM sponge: 10 mm wide and 15 mm tall, with two hollow chambers stacked in a figure-8, and a self-adhesive base. Cut to one continuous length from 10 m to 50 m. Peel the liner, press it onto the door frame or aperture flange, and the round upper chamber and the wider lower chamber both squash down when the door shuts. That two-stage squeeze closes larger and less even gaps than a single bulb, which is why this section is used on classic car doors as well as enclosures, hatches and garden-room doors.
At a glance
- Size: 10 mm wide × 15 mm high; Ø6 mm round bore over a 7 × 5 mm lower hollow
- Walls: 2 mm side walls, 1.5 mm dividing wall between the chambers
- Fixing: self-adhesive tape across the full 10 mm base, so no glue or clips
- Material: expanded (sponge) EPDM, very soft at 40° Shore OO
- Seals gaps: best on closed gaps of about 8 to 11 mm (our guidance)
- Classic cars: the manufacturer makes this section as a replacement door seal for Jaguar Mk 1 saloons (original part numbers BD 10896, BD 10900, BD 17885 and BD 17886)
- Outdoors: ozone, weather and UV resistance rated excellent; flexible at -40 °C
- Supplied as: one continuous length, 10 m to 49 m at £21.34 per metre, or a full 50 m coil at £16.48 per metre (inc VAT)
- Stock: held in stock in the UK and dispatched from stock
Typical uses
- Door aperture seals on classic and kit cars, including the Jaguar Mk 1
- Door seals on electrical enclosures, control cabinets, lockers and kiosks
- Draught and weather seals on shed, workshop, garden-room and loft-hatch doors
- Locker, hatch and tailgate seals on vans, trailers, horseboxes and boats
- Glazing and closure seals on panels, covers and machine guards
- Soft anti-rattle and impact strip where a gap of around 10 mm must be closed
Technical drawing

Specifications
| Property | Value | Test method / basis |
|---|---|---|
| Profile type | Figure-8 double hollow: round upper chamber over a rounded-rectangle lower chamber, flat self-adhesive base | Manufacturer's profile drawing |
| Overall width (across the base) | 10.0 mm | Nominal; tolerance BS 3734 Class E3 |
| Overall height (base to crown) | 15.0 mm | Nominal; tolerance BS 3734 Class E3 |
| Upper bore | Ø6.0 mm | Manufacturer's profile drawing |
| Lower hollow | 7.0 mm wide × 5.0 mm high | Manufacturer's profile drawing |
| Side wall (upper chamber) | 2.0 mm | Manufacturer's profile drawing |
| Dividing wall between chambers | 1.5 mm | Manufacturer's profile drawing |
| Top and base wall, waist notch | About 1.25 mm walls; shallow waist about 1 mm deep each side | Scaled from the manufacturer's drawing; not separately stated |
| Fixing | Self-adhesive tape on the full 10 mm base | Manufacturer product page and datasheet |
| Material | Expanded (sponge) EPDM | Manufacturer datasheet |
| Colour | Black | - |
| Hardness | 40° Shore OO | Shore OO durometer scale (for soft foams); test standard not stated |
| Density | 0.5 to 0.9 g/cm³ | Manufacturer datasheet; method not stated |
| Weight | 0.05 kg per metre (0.5 kg per 10 m, 2.5 kg per 50 m coil) | Manufacturer datasheet |
| Service temperature | Not stated for this profile. EPDM sponge is typically used from about -40 °C to +100 °C (typical for EPDM sponge, not tested on this profile) | Ask us if your job runs hot |
| Low-temperature flexibility | Pass at -40 °C | Manufacturer datasheet |
| Heat ageing | ±30% change after 7 days at 70 °C | Manufacturer datasheet; property measured not stated |
| Compression set | 25% maximum (24 h recovery) on the datasheet; 50% (22 h) on the product page | Manufacturer figures differ; test temperature and standard not stated |
| Water absorption | 5% maximum | Manufacturer datasheet; method not stated |
| Ozone resistance | Excellent | Manufacturer rating |
| Weather resistance | Excellent | Manufacturer rating |
| UV light resistance | Excellent | Manufacturer rating |
| Mould growth resistance | Very good | Manufacturer rating |
| Tensile strength | Not stated for this profile | Ask us if you need it |
| Elongation at break | Not stated for this profile | Ask us if you need it |
| Tear strength | Not stated for this profile | Ask us if you need it |
| Dimensional tolerance | BS 3734 Class E3 (extruded sponge) | BS 3734 |
| Supplied as | One continuous length: any whole metre from 10 m to 49 m, or a full 50 m coil | - |
| Price per metre | £21.34/m inc VAT for 10 to 49 m; £16.48/m on the 50 m coil (£824.19) | - |
The manufacturer's compression set figures differ: 50% after 22 hours on its product page and 25% maximum (24 hour recovery) on its datasheet. We show both. Sponge sections are soft and flexible, so treat all sizes as nominal.
Materials and compliance
Expanded (closed-cell sponge) EPDM. The manufacturer describes it as air and water tight, with outstanding resistance to heat, ozone and weathering, good resistance to steam and polar substances, resistance to ketones and dilute acids and alkalis, and good electrical insulating properties. Like all EPDM it is not suited to oils, fuels or most solvents.
The manufacturer does not state any food-contact (FDA, EC 1935/2004), drinking-water (WRAS), REACH, RoHS or fire-rating approval for this profile, so we do not claim any. If your job needs a certified material, ask us before you order.
How it fits

- Measure the closed gap. It must be under 15 mm so the seal is squeezed. About 8 to 11 mm (roughly 25 to 45% squeeze) is a good starting point; this is our guidance, not a manufacturer figure.
- Check the landing. The face you stick to should be flat and at least 10 mm wide. The flat base goes on the frame and the rounded crown faces the door.
- Clean and dry. Wipe the surface with isopropyl alcohol and let it dry. Fit above about 10 °C so the adhesive grabs well.
- Peel and press. Peel the liner a little at a time and press the strip down firmly along its length. Do not stretch it, or it will shrink back and open gaps at the ends.
- Corners and joins. It follows gentle curves such as car door tops. For tight 90° corners, cut and butt the ends or mitre them. Butt joins tightly and make the join at the top of the door, where water will not sit; a spot of instant adhesive on the ends gives a fully sealed join.
How much do I need?
Add up every edge you want to seal and allow about 5% for trimming. A classic saloon front door opening is typically about 4 to 5 m round, so a four-door car needs roughly 17 to 20 m. A 600 × 800 mm enclosure door takes 2.8 m. Every length is cut as one continuous piece, so you can run several doors from one order. From 39 m upwards the full 50 m coil costs less than a cut length.

Which profile do I need?
| Profile | Size (W × H) | Best for |
|---|---|---|
| EPDM sponge door seal (white) | 9 × 7 mm | Small gaps on interior doors, white wrap-over lip |
| EPDM sponge P-section | 10 × 7 mm | Closed gaps of about 4 to 5.5 mm, hollow bulb with flange |
| EPDM sponge D section | 10 × 8 mm | Medium gaps, single hollow D bulb |
| EPDM sponge door seal, figure-8 (this item) | 10 × 15 mm | Closed gaps of about 8 to 11 mm, double hollow, uneven frames |
| EPDM sponge door seal | 15 × 18 mm | Larger gaps and heavier doors, wider base |
Questions
What gap will it seal?
Any closed gap under its 15 mm height. Aim for about 8 to 11 mm. For smaller gaps choose the 10 × 8 mm D section or the 10 × 7 mm P-section; for bigger gaps use the 15 × 18 mm door seal.
Will it fit my Jaguar Mk 1?
Yes. The manufacturer makes this section as a replacement door seal for Jaguar Mk 1 saloons, matching original part numbers BD 10896, BD 10900, BD 17885 and BD 17886. Check the shape against your old seal before fitting.
Is it self-adhesive?
Yes. The full 10 mm base carries adhesive tape with a peel-off liner. It sticks to clean, dry painted metal, bare metal, wood, glass, most rigid plastics and rubber.
Which way up does it go?
The flat base with the adhesive goes on the frame or flange. The rounded top over the 6 mm bore faces the closing door.
How do I cut and join it?
Scissors or a sharp craft knife gives a clean square end. Butt the ends tightly; for a fully sealed join, glue the ends together with instant adhesive.
Will it go round corners?
Yes, it follows the gentle curves of a car door or a radiused frame. For sharp 90° corners, cut and butt or mitre the strip so it does not lift or pucker.
What temperatures can it take?
The manufacturer states it passes a -40 °C flexibility test but gives no maximum for this profile. EPDM sponge is typically used up to about +100 °C (typical for the material, not tested on this profile). The adhesive may soften before the rubber does, so ask us about hot jobs.
Can I use it outdoors?
Yes. The manufacturer rates its ozone, weather and UV resistance as excellent and mould resistance as very good, and water absorption is 5% maximum.
Will it stand up to oil or fuel?
No. EPDM handles water, steam, weather and dilute acids and alkalis well, but swells in oils, fuels and most solvents.
How is it supplied?
As one continuous piece in the length you choose, from 10 m to 49 m, or as a full 50 m coil. The coil works out cheaper per metre, and from 39 m upwards it is cheaper outright.
Is it food-safe or WRAS approved?
No approvals are stated for this profile, so do not use it where certified food-contact or drinking-water material is required.
Delivery and help
Held in stock and dispatched from the UK. Trade and quantity orders welcome. Not sure it is the right profile? Call +44 1282 277786 or email sales@industrial-polymers.co.uk and we will check it for you.
Product details
| SKU | IP-EPDMS-10X15-10M |
|---|---|
| Weight | 1.1 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:EPDM Sponge Door Seal – 10mm x 15mm Figure-8 Double Hollow, Self-Adhesive, Black – 10m to 50m