
Rubber & FoamSKU IP-EPDMS-19X16.5-9M
EPDM Sponge T Seal – 19mm x 16.5mm – 9m to 49m Lengths or 50m Coil
Price shown updates with the option you pick.
A soft black EPDM sponge T seal with a 19 mm domed head on a 5.5 mm leg, 16.5 mm high overall. Cut to any whole length from 9 m to 49 m in one continuous piece, or buy a full 50 m coil. Push the leg into a slot or groove and the rounded head sits over the gap: when a door, window, hatch or panel closes onto it, the sponge dome squashes down and seals out draughts, dust and water. It also works as a soft finishing and bump strip along slotted frames.
At a glance
- Size: 19 mm head × 16.5 mm high; 5.5 mm leg, 10.5 mm from the foot to the underside of the head
- Material: expanded (sponge) EPDM, very soft at 40° Shore OO
- Fixing: push-fit the leg into a slot about 5 to 5.5 mm wide, or bond it with a rubber-compatible superglue
- Outdoors: rated excellent for ozone, weather and UV; flexible at -40 °C
- Lengths: 9 m to 49 m at £18.93 per metre, or a 50 m coil at £757.50 (£15.15 per metre)
- Stock: held in stock in the UK and dispatched from stock
Typical uses
- Door and window seals on classic and kit cars, where the leg sits in a body or frame channel
- Hatch, cabinet and enclosure doors with a slotted frame
- Glazing, closure and weather strips on caravans, trailers, boats and site cabins
- Soft edge and bump strips along slotted aluminium or timber frames
- Gaskets and expansion-joint fillers in construction and shop-fitting
- Shock and vibration damping in automotive and electronics work
Technical drawing

Specifications
| Property | Value | Test method / basis |
|---|---|---|
| Profile type | T section: domed head on a single solid leg with a rounded foot | Manufacturer's profile drawing |
| Head width (overall width) | 19.0 mm | Nominal; tolerance BS 3734 Class E3 |
| Overall height (foot to top of dome) | 16.5 mm | Nominal; tolerance BS 3734 Class E3 |
| Leg (upright) width | 5.5 mm | Manufacturer's drawing and datasheet. The product page also lists 7.5 mm; the drawing shows 5.5 mm, so we use that |
| Leg height (foot to underside of the head tips) | 10.5 mm | Manufacturer's drawing |
| Head depth at the centre | About 6 mm | Derived: 16.5 mm − 10.5 mm |
| Suggested slot for the leg | About 5 to 5.5 mm wide, 11 mm or more deep | Our guidance from the drawn sizes; not a manufacturer figure |
| Fixing | Plain, no adhesive tape: push-fit the leg into a slot, or bond with a rubber-compatible superglue | Manufacturer recommends superglue |
| Construction | Solid sponge (no hollow core) | Manufacturer's drawing |
| Material | Expanded (sponge) EPDM | Manufacturer datasheet |
| Colour | Black | - |
| Hardness | 40° Shore OO | Shore OO durometer scale (for soft foams); test standard not stated |
| Density | 0.5 to 0.9 g/cm³ | Manufacturer datasheet; method not stated |
| Weight | About 80 g/m (0.08 kg/m): about 4 kg per 50 m coil | Manufacturer datasheet. The product page gives 96 g/m in one place and 0.96 kg/m in another; 0.96 kg/m does not fit the size and density |
| Water absorption | 5% maximum | Manufacturer datasheet; method not stated |
| Compression set | 25% maximum (datasheet, 24 h recovery) · 50% (product page, 22 h) | Manufacturer figures; test temperature and standard not stated. The two sources differ, so plan on the higher figure |
| Heat ageing | ±30% change after 7 days at 70 °C | Manufacturer datasheet; property measured not stated |
| Low-temperature flexibility | Pass at -40 °C | Manufacturer datasheet |
| Ozone resistance | Excellent | Manufacturer rating |
| Weather resistance | Excellent | Manufacturer rating |
| UV light resistance | Excellent | Manufacturer rating |
| Mould growth resistance | Very good | Manufacturer rating |
| Service temperature range | Not stated for this profile. About -40 °C to +100 °C (typical for EPDM sponge, not tested on this profile) | Tested points stated: flexible at -40 °C, aged at +70 °C |
| Tensile strength, elongation at break, tear strength | Not stated for this profile | Ask us if you need them |
| Dimensional tolerance | BS 3734 Class E3 (extruded sponge) | BS 3734 |
| Supplied length | Any whole length from 9 m to 49 m as one continuous piece, or a full 50 m coil | - |
| Price per metre | £18.93/m inc VAT for 9–49 m; £15.15/m inc VAT as a full 50 m coil (£757.50) | - |
All sizes are the manufacturer's nominal figures from its profile drawing. The exact curve of the dome and tips on our drawing is scaled from that drawing. Sponge sections are flexible, so treat all sizes as approximate.
Materials and compliance
Expanded (closed-cell sponge) EPDM. The manufacturer describes the seal as air and watertight with good UV and weather resistance, and describes EPDM as electrically insulating and resistant to ozone, heat, steam, ketones and dilute acids and alkalis. Like all EPDM it is not suited to oils, fuels or solvents.
The manufacturer does not state any food-contact (FDA, EC 1935/2004), drinking-water (WRAS), REACH, RoHS or fire-rating approval for this profile, so we do not claim any. If your job needs a certified material, ask us before you order.
How it fits

- Check the slot. The leg is 5.5 mm wide and 10.5 mm long to the head. A slot about 5 to 5.5 mm wide and at least 11 mm deep holds it with a light squeeze.
- Check the gap. The head stands about 6 mm proud of the frame. It seals best where the closed gap is about 3 to 5 mm.
- Clean the slot. Remove old seal, dirt and grease, and let it dry.
- Push the leg home. Start at one end and press the leg in with your thumb or a plastic roller, without stretching the strip, or it will shrink back from the ends. A rubber mallet helps on long runs.
- Glue if needed. In a loose slot, or with no slot at all, run a rubber-compatible superglue along the leg.
- Corners and joins. The sponge bends round gentle curves. Mitre tight corners. Butt joins tightly and glue the cut faces; put joins where water will not sit.
How much do I need?
Measure round each opening and allow about 5% for trimming. Example: two doors that each measure 1.0 m × 0.9 m round the frame need 2 × (1.0 + 0.9 + 1.0 + 0.9) = 7.6 m; add 5% and choose the 9 m minimum. From 41 m upwards the full 50 m coil costs less, so pick the coil.
Which profile do I need?
| Profile | Size (W × H) | Best for |
|---|---|---|
| EPDM sponge T seal (this item) | 19 × 16.5 mm | Slotted frames; domed head seals a closing door or panel |
| EPDM sponge half round | 12.5 × 6.5 mm | Glue-on lid and door seal where there is no slot |
| EPDM sponge wedge seal | 12 × 6 mm | Tapered edges and doors that close at an angle |
| EPDM sponge D section | 10 × 8 mm | Hollow glue-on seal for doors that close square-on |
| EPDM sponge tailgate seal | 10 × 20 mm | Deeper gaps on tailgates and boot lids |
Data sheet
Download the technical data sheet (PDF): drawing, full specification and compliance
Questions
How is it sold?
Choose a length from 9 m to 49 m and it is cut as one continuous piece at £18.93 per metre, or choose the full 50 m coil at £757.50. The minimum length is 9 m.
How do I fit it?
Push the 5.5 mm leg into a slot or groove about 5 to 5.5 mm wide and at least 11 mm deep, so the head tips rest on the frame. If the slot is loose or there is no slot, glue the leg with a rubber-compatible superglue.
Is this the right size for my car or frame?
Measure the slot width and depth and the closed gap. This profile suits a slot about 5 to 5.5 mm wide and a closed gap of about 3 to 5 mm. Many classic car door and window seals use this size or close to it, but always check your own measurements. Send us a photo or sketch and we will check it.
What can I use it for?
Door, window, hatch and cabinet seals on slotted frames, glazing and weather strips on caravans, boats and cabins, and soft bump or finishing strips along slotted rails.
How do I cut and join it?
A sharp craft knife or scissors gives a clean end. Mitre tight corners and glue butt joins with a rubber-compatible instant adhesive. Do not stretch it while fitting.
Is it self-adhesive?
No. It has no tape. It push-fits into a slot, or you can glue it.
Can I use it outdoors?
Yes. The manufacturer rates its ozone, weather and UV resistance as excellent, and it absorbs no more than 5% water.
What temperatures can it take?
The manufacturer has tested it as flexible at -40 °C and heat-aged it at +70 °C, but does not state a full working range. EPDM sponge typically works from about -40 °C to +100 °C (typical for EPDM sponge, not tested on this profile).
Will it stand up to oil or fuel?
No. EPDM handles water, steam, weather and dilute acids and alkalis well but swells in oils, fuels and most solvents. Ask us for a neoprene or nitrile alternative.
Is it food-safe or WRAS approved?
No approvals are stated for this profile, so do not use it where certified food-contact or drinking-water material is required.
Delivery and help
Held in stock and dispatched from the UK. Trade and quantity orders welcome. Not sure it is the right profile? Call +44 1282 277786 or email sales@industrial-polymers.co.uk and we will check it for you.
Product details
| SKU | IP-EPDMS-19X16.5-9M |
|---|---|
| Weight | 1.81 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:EPDM Sponge T Seal – 19mm x 16.5mm – 9m to 49m Lengths or 50m Coil