
Rubber & FoamSKU IP-EPDMS-12X6-20M
EPDM Sponge Wedge Seal – 12mm x 6mm – 20m to 99m Lengths or 100m Coil
Price shown updates with the option you pick.
A solid, tapered wedge of soft black EPDM sponge, 12 mm wide and 6 mm high, with a flat 12 mm base and a square back. Cut to any whole length from 20 m to 99 m in one continuous piece, or buy a full 100 m coil. The curved face runs from the 6 mm back down to a thin feather toe, so it finishes a raised edge with a soft ramp, closes gaps that narrow along their length, and squeezes into uneven surfaces to seal out draughts, dust and water.
At a glance
- Size: 12 mm wide × 6 mm high, solid section tapering to a feather toe
- Material: expanded (sponge) EPDM, very soft at 40° Shore OO, non-marking
- Fixing: plain flat base: bond it with a contact adhesive or rubber-compatible superglue
- Outdoors: rated excellent for ozone, weather and UV; flexible at -40 °C
- Lengths: 20 m to 99 m at £8.79 per metre, or a 100 m coil at £702.00 (£7.02 per metre)
- Stock: held in stock in the UK and dispatched from stock
Typical uses
- Soft, tapered edging along mats, sheet flooring, panels and paving to reduce trip and impact damage
- Door, window and hatch seals where the gap closes at an angle
- Glazing, closure and weather strips
- Bump and protective strips on equipment, shelving and vehicle panels
- Small expansion-joint fillers and gaskets in construction
- Anti-vibration and shock-absorbing pads in automotive and electronics work
Technical drawing

Specifications
| Property | Value | Test method / basis |
|---|---|---|
| Profile type | Solid sponge wedge: flat base, square back, curved face tapering to a feather toe | Manufacturer's profile drawing |
| Overall width (across the base) | 12.0 mm | Nominal; tolerance BS 3734 Class E3 |
| Overall height (at the square back) | 6.0 mm | Nominal; tolerance BS 3734 Class E3 |
| Flat top before the curve starts | About 3.5 mm | Scaled from the manufacturer's drawing; not separately stated |
| Height at the toe | Tapers to almost nothing (feather edge) | Manufacturer's drawing |
| Bonding face | Flat base, full 12 mm wide | Manufacturer's drawing |
| Fixing | Plain base, no adhesive tape: bond with a contact adhesive or rubber-compatible superglue | Manufacturer recommends superglue; drawing shows no tape |
| Construction | Solid (no hollow core) | Manufacturer's drawing and description |
| Material | Expanded (sponge) EPDM | Manufacturer datasheet |
| Colour | Black | - |
| Hardness | 40° Shore OO | Shore OO durometer scale (for soft foams); test standard not stated |
| Density | 0.5 to 0.9 g/cm³ | Manufacturer datasheet; method not stated |
| Weight | About 40 g/m (0.04 kg/m): about 4 kg per 100 m coil | Manufacturer datasheet. The product page's 0.42 kg/m is inconsistent with the size and density, so we use the datasheet figure |
| Water absorption | 5% maximum | Manufacturer datasheet; method not stated |
| Compression set | 25% maximum (datasheet, 24 h recovery) · 50% (product page, 22 h) | Manufacturer figures; test temperature and standard not stated. The two sources differ, so plan on the higher figure |
| Heat ageing | ±30% change after 7 days at 70 °C | Manufacturer datasheet; property measured not stated |
| Low-temperature flexibility | Pass at -40 °C | Manufacturer datasheet |
| Ozone resistance | Excellent | Manufacturer rating |
| Weather resistance | Excellent | Manufacturer rating |
| UV light resistance | Excellent | Manufacturer rating |
| Mould growth resistance | Very good | Manufacturer rating |
| Marking | Non-marking | Manufacturer description |
| Service temperature range | Not stated for this profile. Typical for EPDM sponge: about -40 °C to +100 °C (typical for EPDM sponge, not tested on this profile) | Tested points stated: flexible at -40 °C, aged at +70 °C |
| Tensile strength, elongation at break, tear strength | Not stated for this profile | Ask us if you need them |
| Dimensional tolerance | BS 3734 Class E3 (extruded sponge) | BS 3734 |
| Supplied length | Any whole length from 20 m to 99 m as one continuous piece, or a full 100 m coil | - |
| Price per metre | £8.79/m inc VAT for 20–99 m; £7.02/m inc VAT as a full 100 m coil (£702.00) | - |
The manufacturer states only the 12 × 6 mm overall size; the flat top and face curve on our drawing are scaled from its profile drawing. Sponge sections are flexible, so treat all sizes as nominal.
Materials and compliance
Expanded (closed-cell sponge) EPDM. The manufacturer describes the profile as non-marking, with good UV and weather resistance, and describes EPDM as air and watertight, electrically insulating, and resistant to ozone, heat, steam, ketones and dilute acids and alkalis. Like all EPDM it is not suited to oils, fuels or solvents.
The manufacturer does not state any food-contact (FDA, EC 1935/2004), drinking-water (WRAS), REACH, RoHS or fire-rating approval for this profile, so we do not claim any. If your job needs a certified material, ask us before you order.
How it fits

- Choose the direction. Put the square 6 mm back against the edge, upstand or frame, and let the curved face run away from it. For a gap seal, the face meets the closing part.
- Check the landing. The surface you bond to should be at least 12 mm wide and flat.
- Clean and dry. Degrease with isopropyl alcohol and let it dry.
- Bond the base. Use a contact adhesive or a rubber-compatible superglue on the flat base. Lay the strip without stretching it, or it will shrink back from the ends.
- Corners and joins. Mitre the ends at corners. Butt joins tightly and glue the cut faces together; put joins where water will not sit.
How much do I need?
Add up the edges and allow about 5% for trimming. Example: edging both long sides and one end of a 10 m × 1.2 m walkway mat needs 10 + 10 + 1.2 = 21.2 m; add 5% and choose 23 m. From 80 m upwards the full 100 m coil costs less, so pick the coil.
Which profile do I need?
| Profile | Size (W × H) | Best for |
|---|---|---|
| EPDM sponge wedge seal (this item) | 12 × 6 mm | Tapered edges and angled gaps; 20–99 m or 100 m coil |
| EPDM sponge half round | 10 × 5 mm | Low, symmetrical lid and door seals |
| EPDM sponge crown strip | 10 × 5 mm | Self-adhesive, multi-ridge gap seal |
| EPDM sponge D section | 10 × 8 mm | Hollow seal for doors that close square-on |
Data sheet
Download the technical data sheet (PDF): drawing, full specification and compliance
Questions
How is it sold?
Choose a length from 20 m to 99 m and it is cut as one continuous piece at £8.79 per metre, or choose the full 100 m coil at £702.00. The minimum length is 20 m.
Which way round does it go?
The flat 12 mm side is the base you glue down. The square 6 mm side is the back, which sits against an edge or frame. The curved face slopes down to the thin toe.
What gap will it seal?
Gaps up to about 5 mm at the back, narrowing towards the toe. It suits doors, hatches and lids that close at an angle or gaps that vary along their length. For a square-on door gap, a D section or half round compresses more evenly.
Is it self-adhesive?
No. The base is plain, so bond it with a contact adhesive or a rubber-compatible superglue.
How do I cut and join it?
A sharp craft knife or scissors gives a clean end. Mitre corners and glue butt joins with a rubber-compatible instant adhesive.
Can I use it outdoors?
Yes. The manufacturer rates its ozone, weather and UV resistance as excellent, and it absorbs no more than 5% water.
What temperatures can it take?
The manufacturer has tested it as flexible at -40 °C and heat-aged it at +70 °C, but does not state a full working range. EPDM sponge typically works from about -40 °C to +100 °C (typical for EPDM sponge, not tested on this profile).
Will it mark floors or paintwork?
The manufacturer describes it as non-marking.
Will it stand up to oil or fuel?
No. EPDM handles water, steam, weather and dilute acids and alkalis well but swells in oils, fuels and most solvents. Ask us for a neoprene or nitrile alternative.
Is it food-safe or WRAS approved?
No approvals are stated for this profile, so do not use it where certified food-contact or drinking-water material is required.
Delivery and help
Held in stock and dispatched from the UK. Trade and quantity orders welcome. Not sure it is the right profile? Call +44 1282 277786 or email sales@industrial-polymers.co.uk and we will check it for you.
Product details
| SKU | IP-EPDMS-12X6-20M |
|---|---|
| Weight | 1.98 lb |
More from this range
Request a quote
Fast, no-obligation price from our UK team for:EPDM Sponge Wedge Seal – 12mm x 6mm – 20m to 99m Lengths or 100m Coil