
Rubber & FoamSKU IP-ICPR-250X36-BLACK
Rubber Cable Protector – 250mm x 36mm, 60mm x 27mm Channel – 1.5m Length
Price shown updates with the option you pick.
This rubber cable protector 250mm x 36mm is a wide, low-profile floor cover with a single 60mm x 27mm channel, built to shield power cables, hoses and air lines where forklifts, pallet trucks and vans cross them. It is sold as one 1.5m length, in black or grey.
At a glance
- Heavy duty cable cover: 250mm wide, 36mm high, 1.5m long
- One large 60mm wide x 27mm high cable channel
- Split base opens so cables are laid in from below, not threaded from the end
- Toughened natural rubber / SBR blend, 75 Shore A
- Gently sloped sides for wheeled traffic and wheelchairs
- UV stable, halogen free, tested to BS 476 Part 7 Class 3
Typical uses
- Temporary power runs across warehouse aisles and loading bays
- Hose and cable crossings on construction sites and yards
- Machine shop floors where leads run between workstations
- Event, exhibition and outdoor site cable ramps
- Protecting compressed air lines and welding leads from vehicle damage
Which one do I need?
| Cable protector | Channel | Best for |
|---|---|---|
| 180mm x 36mm | 30mm hole | Single round cables or hoses up to about 30mm |
| 250mm x 36mm (this item) | 60mm x 27mm | Several leads side by side, flat bundles, hoses up to about 27mm high |
| 270mm x 68mm | 53mm channel | Thick armoured cables and large hoses |
| 330mm x 85mm | Large channel | The biggest cable bundles and fuel or water hoses |
Technical drawing
Specification
| Product | Rubber cable protector, single channel |
| Width | 250mm |
| Height | 36mm |
| Channel size | 60mm wide x 27mm high |
| Length | 1.5m per length |
| Material | Natural rubber / SBR blend |
| Hardness | 75 Shore A |
| Colours | Black or grey |
| Fire testing | BS 476 Part 7 Class 3 |
| Halogens | None |
| Unit of sale | One 1.5m length |
How much do I need?
Measure the width of the route the cable crosses and divide by 1.5m, rounding up. A 4m wide aisle needs three lengths (4.5m of cover); a 6m roller-door opening needs four. Lay the lengths end to end and butt them tight so the channel runs continuously.
Fitting tips
- Sweep the floor first so grit does not lift the edges of the cover.
- Open the split in the base, lay the cables in the channel and let the base close around them.
- Keep cables flat side by side inside the 60mm channel rather than stacked.
- Butt neighbouring lengths tightly and keep the whole run straight across the traffic route.
- Check the cover after heavy use and replace any length with torn sides.
Complete your project
- Rubber Cable Protector – 180mm x 36mm, 30mm Hole – 4.5m Length
- Rubber Cable Protector 270mm x 68mm – 53mm Channel – 1.5m Length
- Industrial Rubber Cable Protector – 330mm x 85mm – 1.5m Length
Questions
What size cables fit this cable protector?
The channel is 60mm wide and 27mm high, so it takes one hose or cable up to about 27mm across, or several smaller leads laid side by side.
Do I have to thread the cable through from the end?
No. The base is split along its length, so you pull it open, lay the cables in from underneath and let it close again.
Can vehicles drive over this rubber cable cover?
Yes. It is a heavy duty rubber cable ramp for wheeled site and warehouse traffic, and the sloped sides let trolleys and wheelchairs roll across.
Is it suitable for outdoor use?
Yes. The rubber is UV stable, so it can stay in place on yards and outdoor sites.
Black or grey - is there any difference?
Only the colour. Grey stands out more on dark tarmac; black blends in on most warehouse floors.
Need help choosing the right cable protector? Contact our team.
Product details
| SKU | IP-ICPR-250X36-BLACK |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Rubber Cable Protector – 250mm x 36mm, 60mm x 27mm Channel – 1.5m Length