
Rubber & FoamSKU IP-IHVCP-178X30-STD
Hi-Vis Rubber Cable Protector – 178mm x 30mm, 3 x 23mm Channels – 4.5m Length
This hi-vis cable protector 178mm x 30mm is a heavy rubber floor ramp with three 23mm channels and bright yellow side strips, made to guard power cables, hoses and pipes where vehicles and pedestrians cross. It is sold as one 4.5m length.
At a glance
- 178mm wide x 30mm high low-profile ramp
- Three cable channels, each 23mm diameter
- Yellow strips along both sides as a clear hazard warning
- Tough NR/SBR rubber at 75 Shore A for industrial vehicle traffic
- Split base lets cables be pressed in and lifted out without threading
- Supplied as a single 4.5m length
Typical uses
- Protecting power cables across warehouse and factory floors
- Guarding air and water hoses at workshop crossings
- Temporary cable runs at loading bays and yards
- Keeping walkways safe where leads must cross a route
- Site and event cable crossings with wheelchair-friendly low ramps
Which one do I need?
| Protector | Best for |
|---|---|
| Hi-vis 178 x 30mm, 3 x 23mm (this product) | Three medium cables or hoses with a high-visibility warning edge |
| Rubber 127 x 28mm, 23mm hole | A single cable or hose on a narrower run |
| Rubber 180 x 36mm, 30mm hole | Larger single cables or hoses up to 30mm |
Technical drawing
Specification
| Material | NR/SBR rubber |
| Hardness | 75 Shore A |
| Width | 178mm |
| Height | 30mm |
| Channels | 3, each 23mm diameter |
| Colour | Black with yellow side strips |
| Unit of sale | One 4.5m length |
How much do I need?
Measure the width of the route each cable crosses and round up to whole 4.5m lengths. Example: a 4m wide aisle needs one length; a 7m wide loading bay needs two lengths laid end to end.
Check that each cable or hose is no more than 23mm across so it sits fully inside its channel.
Fitting tips
- Lay the protector flat on a clean, swept floor so the base sits evenly.
- Open the split in the base and press each cable up into its channel; the rubber closes back around it.
- Keep each cable in a channel of its own rather than doubling up.
- Run the protector square to the traffic so wheels cross it straight.
- Unroll it a few hours before use in cold weather so it lies flat.
Complete your project
- Rubber Cable Protector – 127mm x 28mm, 23mm Hole
- Rubber Cable Protector – 180mm x 36mm, 30mm Hole
- Industrial Rubber Cable Protector – 330mm x 85mm
Questions
What size cables fit this hi-vis cable protector?
Each of the three channels is 23mm in diameter, so cables, hoses or pipes up to 23mm across fit one per channel.
Do I have to thread cables through it?
No. The base is split, so you open it and push the cables up into the channels, then lift them out again when needed.
Can vehicles drive over it?
Yes. It is a heavy-duty rubber protector made for industrial areas with vehicle traffic, and its low 30mm profile keeps the crossing gentle.
Why the yellow strips?
They run along both sides to mark the crossing as a trip hazard and make it easy to see on a grey floor.
How long is each piece?
Each protector is one 4.5m length, 178mm wide and 30mm high.
Need help choosing? Contact our team for practical advice on sizes, materials and fitting.
Product details
| SKU | IP-IHVCP-178X30-STD |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Hi-Vis Rubber Cable Protector – 178mm x 30mm, 3 x 23mm Channels – 4.5m Length