
Rubber & FoamSKU IP-PVCET-6.5X9.5-50M
Self-Grip PVC Edge Trim – 6.5mm x 9.5mm – Fits 1mm to 1.5mm Panels – 50m Coil
A black PVC edge trim with a steel carrier that pushes onto 1 mm to 1.5 mm sheet edges and holds by grip alone, with no glue. The profile is 6.5 mm wide and 9.5 mm high, with a 1.5 mm slot. A U-shaped steel strip runs inside the PVC for the full length and keeps the jaws clamped, while two flexible fins inside the channel fold up against both faces of the panel and stop it pulling off. It covers sharp cut edges, protects the panel from knocks and gives a neat, finished look. It comes as one continuous 50 m coil and is in stock in the UK for same-day dispatch.
At a glance
- Fits: sheet metal, plastic, fibreglass and board edges 1 mm to 1.5 mm thick
- Size: 6.5 mm wide × 9.5 mm high, 1.5 mm slot
- Construction: flexible PVC, 67° to 82° Shore A, moulded over a U-shaped steel carrier
- Grip: twin internal fins and the steel clamp hold it on with no adhesive, so it can be removed and refitted
- Working temperature: −10 °C to +60 °C
- Supplied as: one 50 m coil, £312.57 inc VAT (£6.25 per metre)
Technical drawing

All dimensions are in mm and nominal. The drawing is not to scale. The carrier and fin shapes are shown as typical.
Specifications
| Property | Value | Test method / basis |
|---|---|---|
| Profile | Self-gripping U edge trim with steel carrier and twin internal gripping fins | Manufacturer drawing |
| Overall width | 6.5 mm | Manufacturer drawing and data sheet |
| Overall height | 9.5 mm | Manufacturer drawing and data sheet |
| Slot opening (unflexed) | 1.5 mm | Manufacturer drawing |
| Panel thickness it fits | 1.0 mm to 1.5 mm | Manufacturer product data (range data sheet lists 0.8 mm to 1.5 mm) |
| Side wall each side of the slot | 2.5 mm | Calculated: (6.5 − 1.5) ÷ 2 |
| Jacket material | Flexible PVC | Manufacturer |
| Carrier | Steel, U-shaped, full length | Manufacturer |
| Colour | Black | Manufacturer |
| Hardness | 67° to 82° Shore A | Manufacturer data; method not stated |
| Minimum working temperature | −10 °C | Manufacturer data |
| Maximum working temperature | +60 °C | Manufacturer data |
| Density | Not stated for this profile | Ask us if you need it |
| Tensile strength | Not stated for this profile | Ask us if you need it |
| Elongation at break | Not stated for this profile | Ask us if you need it |
| Tear strength | Not stated for this profile | Ask us if you need it |
| Compression set | Not stated for this profile | Ask us if you need it |
| Dimensional tolerance | Not stated; dimensions are nominal | Ask us if you need it |
| Supplied as | One continuous 50 m coil | — |
| Price | £312.57 inc VAT per coil (£6.25 per metre) | — |
Materials and compliance
The trim is a flexible PVC jacket moulded over a steel carrier. PVC stands up well to moisture, weather and many everyday chemicals, so the trim can be used indoors and outdoors within its −10 °C to +60 °C range. The manufacturer does not state any food-contact (FDA, EC 1935/2004), drinking-water (WRAS), fire-rating, REACH, RoHS or other product approvals for this profile, so we do not claim any. Do not use it where a certified material is required; ask us for a certified alternative.
How it fits

- Check the edge. The panel should be 1 mm to 1.5 mm thick. Deburr the edge and make sure it is clean and dry.
- Push on. Start at one end and press the trim fully onto the edge by hand, working along the run.
- Seat it. Tap along the top with a rubber or plastic mallet until the edge reaches the top of the channel. You need no adhesive.
- Cut and finish. Cut through the PVC and steel with side cutters, tin snips or a fine hacksaw. Butt the ends tightly together.
Typical uses
- Finishing cut edges on sheet steel and aluminium panels, enclosures and computer or electrical cabinets
- Safety edging on machine guards, brackets and access hatches
- Garage doors, sheds, playground equipment and other outdoor sheet edges
- Fibreglass, plastic and composite panels in marine and vehicle interiors
- Interior side panels, trim panels and side window surrounds
- Protecting sheet and glass edges in storage and transport
FAQ
What thickness of panel does it fit?
It is made for edges 1 mm to 1.5 mm thick, which covers most 1.2 mm sheet steel and aluminium. It will not grip firmly on thinner material. For 1.5 mm to 3 mm edges, choose a larger self-grip trim such as the 12 × 15.5 mm size.
How is it different from the 5.5 × 8.5 mm trim?
Both fit 1 mm to 1.5 mm edges. This one is larger, at 6.5 × 9.5 mm, so it gives a fuller, more visible edge and more cushioning against knocks. It also grips with two symmetrical fins rather than a barb and arm.
How much do I need?
Measure the total run in metres and add about 5 % for cuts and corners. One coil covers up to 50 m. If you need a shorter piece, our 5.5 × 8.5 mm trim is sold in lengths from 14 m.
Do I need glue?
No. The steel carrier keeps the jaws clamped and the two fins hold the trim on. Because there is no adhesive, you can remove it and fit it again.
Will it go round corners and curves?
Yes. The steel carrier bends, so the trim follows curves and radiused corners. For a sharp 90° external corner, cut a small V-notch in the inside of the trim so it folds neatly without bunching.
How do I cut and join it?
Because of the steel carrier, a knife alone will not do. Use side cutters, tin snips or a fine-tooth hacksaw, then trim any burr. Butt the ends tightly for a neat joint; no joining piece is needed.
What temperatures can it take?
The manufacturer rates it for −10 °C to +60 °C. It is not suitable for hot engine bays, ovens or places that get very cold. Ask us about a silicone or EPDM trim for those.
Can it be used outdoors?
Yes. PVC resists moisture and weather well, so it suits garage doors, sheds and outdoor equipment within its temperature range.
What is it made of?
A flexible black PVC jacket, 67° to 82° Shore A, moulded over a U-shaped steel carrier, with two gripping fins inside the channel.
Is it food safe or fire rated?
No approvals are stated for this profile, so do not use it where food-contact, drinking-water or fire certification is needed.
Complete your project
- Self-Grip PVC Edge Trim – 5.5mm x 8.5mm – 14m to 50m lengths
- PVC Self-Grip Edge Trim – 12mm x 15.5mm – for thicker panels
- Silicone Self-Grip Edge Trim – 8.9mm x 12.4mm – 1mm to 4mm panels
- EPDM U Channel – 4.8mm x 9.6mm – fits 1.6 mm panels
Need help choosing or fitting? Call +44 1282 277786, email sales@industrial-polymers.co.uk or contact our team.
Product details
| SKU | IP-PVCET-6.5X9.5-50M |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Self-Grip PVC Edge Trim – 6.5mm x 9.5mm – Fits 1mm to 1.5mm Panels – 50m Coil