Rubber & FoamSKU IP-SILP-10X3-7BEC-BLACK
Silicone L Profile – 10mm x 3mm – 25m Coil
This silicone L profile 10mm x 3mm is a very low angle extrusion: a flat 10mm base only 1mm thick, with a 3mm upright 1.5mm thick, and a chamfered tip that feathers the base down onto the surface. It caps and protects thin sheet, glass and panel edges with almost no visible build-up. Solid 60 Shore A silicone, rated -50°C to +180°C, food-contact compliant and WRAS approved. Sold as a continuous 25m coil (£27.00 per metre inc VAT) in seven colours, held in stock.
At a glance
- 10mm wide x 3mm high L section; 1mm base, 1.5mm upright
- 2mm inside drop: covers the whole edge of sheet up to 2mm thick
- 1mm chamfered base tip: no hard step to catch or lift
- 60 Shore A silicone: flexible, cuts cleanly with a knife
- -50°C to +180°C working range; resists UV, ozone and weathering
- FDA 21 CFR 177.2600, EC 1935/2004 and WRAS approved material
- Black, blue, green, red, translucent, white or yellow; 25m coil
Technical drawing
![]()
How it fits
The L sits with its 10mm base flat on the face and its 3mm upright over the edge. With 1mm of silicone over the face, the inside drop is 2mm, so on sheet up to 2mm thick the upright covers the full edge; on thicker material it caps the top 2mm of the edge as a corner protector.
![]()
Specifications
| Property | Value | Test method / note |
|---|---|---|
| Material | Solid silicone rubber | - |
| Section | Low L (angle) with chamfered base tip | - |
| Overall width (base) | 10.0 mm | Nominal |
| Overall height (upright) | 3.0 mm | Nominal |
| Upright thickness | 1.5 mm | Nominal |
| Base thickness | 1.0 mm | Nominal |
| Base tip chamfer | 1.0 mm x 1.0 mm | Nominal |
| Inside width / inside drop | 8.5 mm / 2.0 mm | Calculated from the nominal dimensions |
| Dimensional tolerance | Class E2 | ISO 3302-1:2014 |
| Coil length | 25 m continuous | - |
| Hardness | 60 Shore A | DIN ISO 48-4 |
| Density | 1.15 g/cm³ | DIN EN ISO 1183-1 A |
| Tensile strength | 11 N/mm² (11 MPa) | ISO 37 Type 1 |
| Elongation at break | 550 % | ISO 37 Type 1 |
| Tear strength | 26 N/mm | ASTM D 624 B |
| Compression set, 22 h at 175°C | 31 % | DIN ISO 815-1 Type B, Method A |
| Rebound resilience | 59 % | ISO 4662 |
| Working temperature | -50°C to +180°C | - |
| Environmental resistance | Ozone, UV, oxidation, weathering, cosmic and ionising radiation, corona discharge | - |
| Colours | Black, blue, green, red, translucent, white, yellow | - |
Materials and compliance
- FDA: the silicone complies with 21 CFR 177.2600 (rubber articles for repeated food contact).
- EU food contact: complies with EC 1935/2004.
- WRAS: WRAS approved material, for use with potable water.
- Free from TSE/BSE-derived products.
- Free from phthalates.
Compliance applies to the material. Confirm suitability for your own process and conditions of use.
Typical uses
- Edge capping on thin sheet metal, polycarbonate and acrylic up to 2mm
- Low-profile protection for glass edges on cabinets, displays and partitions
- Discreet corner trim on enclosures, HVAC panels and machine guards
- Food and beverage equipment where a food-contact grade is needed
- Potable water equipment, using the WRAS approved material
- Colour-coded edges in cleanrooms, labs and production areas
- Edging on caravans, motorhomes and classic vehicle trim panels
Which one do I need?
| Profile | Best for |
|---|---|
| Silicone L profile 10mm x 3mm (this item) | The flattest option: 1mm over the face, caps edges up to 2mm thick |
| Silicone L profile 10mm x 4mm | Slightly deeper upright for a little more edge cover |
| Silicone L profile 10mm x 5mm | Deeper drop for thicker panels |
| Silicone L profile 10mm x 10mm, thin wall | Equal legs when both faces of a corner need covering |
How much do I need?
Add up every edge and allow about 5% for trimming. Example: capping the top and both side edges of ten 900mm x 1200mm panels needs 10 x (0.9 + 1.2 + 1.2) = 33m, about 34.7m with allowance, so order two 25m coils.
Fitting tips
- Clean and degrease the edge first; silicone will not grip an oily surface.
- Cut with a sharp knife or scissors for a clean, square end; mitre corners at 45°.
- Many edge-protection jobs need no adhesive. For a permanent or watertight fit, run a thin bead of compatible silicone or polyurethane sealant inside the angle.
- Lay the strip on relaxed, not stretched, so the ends do not pull back.
Data sheet
Download the technical data sheet (PDF)
Frequently asked questions
How do I fit it?
Seat the inside corner of the L on the edge, with the 10mm base on the face and the 3mm upright over the edge. On many jobs it stays in place on its own; bond it with silicone or PU sealant inside the angle for a permanent or sealed fit.
What thickness of panel does it suit?
The inside drop is 2mm, so it fully covers the edge of sheet, glass or panel up to 2mm thick. On thicker material it protects the corner and the top 2mm of the edge.
Can I cut and join it?
Yes. Cut it with a sharp knife or scissors. Mitre corners at 45°, and join ends with a silicone adhesive or sealant. Butt the ends together without stretching the strip.
What temperatures will it take?
-50°C to +180°C continuous working range, so it suits ovens, hot equipment and cold stores alike.
Is it food safe?
The silicone complies with FDA 21 CFR 177.2600 and EC 1935/2004 for food contact, and is free from phthalates and TSE/BSE-derived products. Check suitability for your exact process.
Can it be used outdoors or near water?
Yes. It resists UV, ozone and weathering, and the material is WRAS approved for potable water use.
Which colour should I choose?
Black and translucent are the most discreet. Blue, green, red, yellow and white suit colour coding; blue is often chosen in food areas because it is easy to spot.
Is it in stock, and how long is the coil?
Yes, all seven colours are held in stock. Each order line is one continuous 25m coil.
Complete your project
- Silicone L Profile – 10mm x 4mm – 25m Coil
- Silicone L Profile – 10mm x 10mm, Thin 1.5mm Wall – 25m Coil
- Silicone L Profile – 3mm x 1mm – 25m Coil
Need help choosing a profile? Call +44 1282 277786, email sales@industrial-polymers.co.uk, or contact our team.
Product details
| SKU | IP-SILP-10X3-7BEC-BLACK |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Silicone L Profile – 10mm x 3mm – 25m Coil