Rubber & FoamSKU IP-SILP-10X4X2-BLACK
Silicone L Profile – 10mm x 4mm – 25m Coil
A slim, low-profile silicone angle (L) trim: 10mm wide by just 4mm high, with a 2mm wall on both legs. Lay the wide 10mm leg on the face of a panel and the 4mm upright covers the edge, giving a soft, neat finish that protects the edge, cushions knocks and helps seal the joint. The 60 Shore A silicone stays flexible from -50°C to +180°C and is made from a compound with written FDA, EC 1935/2004 and WRAS approvals. Sold as a continuous 25m coil in seven colours, held in stock for same-day dispatch.
At a glance
- Size: 10mm wide x 4mm high, 2mm upright wall, 2mm base wall
- Inside of the angle: 8mm along the base and 2mm up the upright
- Material: solid silicone rubber, 60 Shore A (medium, flexible)
- Temperature: -50°C to +180°C working range
- Approvals: FDA 21 CFR 177.2600, EC 1935/2004, WRAS approved material
- Weathering: resists UV, ozone, oxidation and outdoor exposure
- Colours: black, blue, green, red, translucent, white, yellow, all at one price
- Supplied as: one 25m coil (£27.00 per metre inc VAT)
Technical drawing
![]()
Specification
| Property | Value | Test method / note |
|---|---|---|
| Profile type | Solid L / angle section, low profile | - |
| Overall width (base leg) | 10.0 mm | Nominal |
| Overall height (upright) | 4.0 mm | Nominal |
| Upright wall thickness | 2.0 mm | Nominal |
| Base wall thickness | 2.0 mm | Nominal |
| Inner leg, base (10 - 2) | 8.0 mm | Derived from the nominal sizes |
| Inner leg, upright (4 - 2) | 2.0 mm | Derived from the nominal sizes |
| Dimensional tolerance | Class E2 | ISO 3302-1:2014 |
| Coil length | 25 m continuous | - |
| Material | Silicone rubber | - |
| Hardness | 60 Shore A | DIN ISO 48-4 |
| Density | 1.15 g/cm³ | DIN EN ISO 1183-1 A |
| Tensile strength | 11 N/mm² (MPa) | ISO 37 Type 1 |
| Elongation at break | 550 % | ISO 37 Type 1 |
| Tear strength | 26 N/mm | ASTM D 624 B |
| Compression set, 22 h at 175°C | 31 % | DIN ISO 815-1 Type B, Method A |
| Rebound resilience | 59 % | ISO 4662 |
| Working temperature | -50°C to +180°C | - |
| Environmental resistance | Ozone, UV, oxidation, weathering, cosmic and ionising radiation, corona discharge | Manufacturer's material data |
| Colours | Black, blue, green, red, translucent, white, yellow | Same data for every colour |
Materials and compliance
The manufacturer's data for this profile states the following in writing:
- FDA 21 CFR 177.2600 compliant compound (rubber articles for repeated food contact)
- EC 1935/2004 compliant for food-contact materials
- WRAS approved material, for use with potable (drinking) water
- Free from TSE/BSE-derived by-products
- Free from phthalates
Food-contact and WRAS approvals apply to the material. Check the finished installation against the rules for your own application.
Typical uses
- Slim edge trim on sheet-metal machine guards, panels, cabinets and enclosures
- Low corner seal where a panel meets a frame on food, drink and pharma equipment
- Soft edge on glass, acrylic and polycarbonate panels in displays, cabinets and screens
- Finishing strip on cleanroom, laboratory and HVAC fit-outs
- Potable-water equipment where a WRAS approved material is specified
- Colour-coded edges for hygiene zoning, identification or safety marking
- Caravan, motorhome, classic car and rail interior trim
Which size do I need?
This is the slimmest 10mm-wide angle in the range: the upright stands only 4mm proud, and the space inside the L is 8mm across and 2mm high. Choose a taller upright if you need to wrap a thicker edge.
| Profile | Upright height | Best for |
|---|---|---|
| 10mm x 3mm | 3mm | Flattest finish, lowest lip |
| 10mm x 4mm (this one) | 4mm | Slim 4mm lip with 2mm walls |
| 10mm x 5mm | 5mm | Slightly deeper lip |
| 10mm x 7mm | 7mm | Deeper wrap for thicker edges |
How much do I need?
Add up every edge you want to cover and allow about 5% for trimming and mitred corners. Edging four guard doors, each 600mm x 900mm, all the way round takes 4 x 3.0m = 12m, plus 5% = about 12.6m, so one 25m coil covers the job with plenty to spare.
Fitting
- Clean and dry the edge. Remove oil, dust and old sealant.
- Lay the coil flat for a few hours so it relaxes straight.
- Cut to length with a sharp knife against a straightedge. Cut square for butt joints, or mitre at 45° on outside corners.
- Position the profile so the inside corner of the L sits tight against the edge, then work along the full length.
- For a permanent or watertight fit, bond it with a compatible silicone or polyurethane adhesive/sealant.
Frequently asked questions
How do I fit it?
Lay the 10mm leg flat on the face of the panel with the 4mm upright over the edge. On many edges it can be positioned without adhesive. Where it must not move, or must keep water out, bond it with a compatible silicone or polyurethane sealant.
What size of edge does it suit?
The inside of the angle is 8mm across the base and 2mm up the upright; the outside is 10mm x 4mm. It is made for thin edges and for a slim, low trim line. For thicker edges, see the 10mm x 5mm and 10mm x 7mm sizes in the table above.
What is it used for?
Protecting and finishing sharp sheet and panel edges, sealing low panel-to-frame corners, and colour-coded or hygienic trim on food, water, laboratory and HVAC equipment.
Is it safe for food and drinking water?
The silicone compound is stated to comply with FDA 21 CFR 177.2600 and EC 1935/2004 for food contact, and it is a WRAS approved material for potable water. It is also free from phthalates and TSE/BSE-derived ingredients.
What temperatures can it take?
-50°C to +180°C. It stays flexible in freezers and cold stores and keeps its shape near ovens and hot equipment. It also resists UV, ozone and weathering, so it can be used outdoors.
How hard or flexible is it?
60 Shore A, a medium grade of silicone. It is soft enough to cushion knocks and follow gentle curves, and firm enough to hold a straight line on an edge.
Can I cut and join it?
Yes. Cut it with a sharp knife or shears. For corners, mitre two ends at 45°. Joints can be sealed or bonded with a silicone adhesive/sealant; ordinary superglue does not bond well to silicone.
Does the colour change the specification?
No. All seven colours are the same 10mm x 4mm profile in the same 60 Shore A silicone with the same data and the same price.
Is it in stock?
Yes. All colours are held in stock as 25m coils and dispatched the same day on qualifying orders.
Need help choosing a profile or colour? Contact our team, call +44 1282 277786 or email sales@industrial-polymers.co.uk.
Product details
| SKU | IP-SILP-10X4X2-BLACK |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Silicone L Profile – 10mm x 4mm – 25m Coil