Rubber & FoamSKU IP-SILP-3X1-BLACK
Silicone L Profile – 3mm x 1mm – 25m Coil
This 3mm x 1mm silicone L profile is the finest angle trim in our silicone range: a flat 3mm base with a tiny 1mm-high lip along one side. It finishes and protects small corners and thin edges on enclosures, instrument cases, glazing, light sheet metal and food or lab equipment, where a bulkier trim would look clumsy or not fit at all. It is sold as one continuous 25m coil in seven colours, which works out at £27.00 per metre inc VAT.
At a glance
- Micro angle trim: 3mm wide x 1mm high overall
- Solid section: 0.5mm-thick base and 0.5mm-wide upright lip
- Firm 80 Shore A silicone keeps a crisp, straight line
- Works from -50°C to +180°C
- Food-contact compliant (FDA 21 CFR 177.2600, EC 1935/2004) and WRAS-approved material
- Resists UV, ozone, weathering and radiation
- Seven colours for colour coding or a matched finish
- Held in stock for fast dispatch
Typical uses
- Fine edge finishing on instrument cases, control panels and small enclosures
- Corner protection on thin glass, acrylic and polycarbonate sheets
- Low-profile trim on food and drink processing and handling equipment
- Clean, easy-wipe edges in laboratories and cleanrooms
- Colour-coded edge marking on panels, guards and fixtures
- Small heat-resistant trims near ovens, lamps and warm equipment
Which one do I need?
| Profile | Best for |
|---|---|
| 3mm x 1mm (this item) | The finest edges, where only a very thin, low trim will fit |
| 4.5mm x 3.7mm | Small, firm trim with a thicker, more protective section |
| 5mm x 3mm, 40 Shore A | A softer, more flexible trim that compresses into gaps |
| 6.2mm x 5.2mm | Larger edges that need more cover |
Technical drawing
![]()
Specification
| Property | Value | Test method |
|---|---|---|
| Product | Silicone L profile (angle trim) | – |
| Overall width | 3mm | – |
| Overall height | 1mm | – |
| Wall thickness | 0.5mm base, 0.5mm upright lip | – |
| Dimensional tolerance | ISO 3302-1:2014, Class E2 | – |
| Material | Solid silicone rubber | – |
| Hardness | 80° Shore A | DIN ISO 48-4 |
| Density | 1.20 g/cm³ | DIN EN ISO 1183-1 A |
| Tensile strength | 10 N/mm² | ISO 37 Type 1 |
| Elongation at break | 440% | ISO 37 Type 1 |
| Tear strength | 28 N/mm | ASTM D 624 B |
| Compression set (22 hours at 175°C) | 78% | DIN ISO 815-1 Type B, Method A |
| Rebound resilience | 54% | ISO 4662 |
| Working temperature | -50°C to +180°C | – |
| Colours | Black, blue, green, red, translucent, white, yellow | – |
| Unit of sale | One continuous 25m coil (£27.00 per metre inc VAT) | – |
Typical values for guidance.
Material and compliance
Every claim below comes from the manufacturer's technical data for this exact profile.
- Food contact: the compound meets FDA 21 CFR 177.2600 and EC 1935/2004, so it can be used on food and drink processing and handling equipment.
- Drinking water: made from a WRAS-approved material, suitable for potable water and public water supply applications.
- Clean composition: free from TSE/BSE-derived by-products and free from phthalates.
- Environmental resistance: stands up to ozone, UV, oxidation, weathering, cosmic and ionising radiation, and corona discharge.
Need compliance paperwork for an audit? Contact our team and we will send what is available for your order.
How much do I need?
Add up the length of every edge you want to trim, then add about 5% for cutting and corners. Example: 30 instrument lids, each with two 400mm edges to finish, need 30 x 0.8m = 24m, plus 5% = about 25.2m. That is just over one 25m coil, so order two, or trim one edge fewer per lid.
Fitting tips
- Clean and degrease the edge first; silicone will not bond to an oily surface.
- For a permanent or watertight fit, run a very thin bead of silicone or polyurethane adhesive sealant inside the angle. On a section this small, less is more.
- For light-duty edge protection, the trim can often be positioned without adhesive.
- Cut with a fresh, sharp blade so the tiny lip stays square and clean.
- Lay the trim in without stretching it, so it does not shrink back while the adhesive cures.
Complete your project
- Silicone L Profile – 4.5mm x 3.7mm – 25m Coil
- Silicone L Profile – 5mm x 3mm, Soft 40 Shore A – 25m Coil
- Silicone Round U Channel – 3mm x 5mm – 25m Coil
Data sheet
Download the technical data sheet (PDF)
Questions
How small is this profile in real life?
Very small. The whole section is 3mm across and 1mm high, with 0.5mm walls, so once fitted it reads as a fine line along the edge. Check the technical drawing above before ordering, and if you need more cover choose the 4.5mm x 3.7mm size.
Is it safe for food contact?
Yes. The compound complies with FDA 21 CFR 177.2600 and EC 1935/2004, and it is free from TSE/BSE-derived by-products and phthalates.
Can it be used on drinking water equipment?
Yes. It is made from a WRAS-approved material for potable water use.
Will it work outdoors or near heat?
Yes. Silicone resists UV, ozone, oxidation and weathering, and this compound is rated from -50°C to +180°C.
Is it a compression seal?
Not really. At 80 Shore A it is a firm trim designed to hold a neat edge. Compression set is 78% after 22 hours at 175°C, so for gaps that are squeezed shut choose a softer seal such as the 40 Shore A L profile.
Do I need adhesive?
For light edge protection it can often be fitted without. For a permanent or watertight result, bond it with a compatible silicone or polyurethane adhesive sealant.
How accurate is the size?
It is extruded to ISO 3302-1:2014 tolerance class E2, the international standard for dimensional tolerances on extruded rubber profiles.
How is it supplied, and can I mix colours?
Each order line is one continuous 25m coil in a single colour. To get several colours, add one coil of each to your basket.
Need help choosing a size? Contact our team.
Product details
| SKU | IP-SILP-3X1-BLACK |
|---|
More from this range
Request a quote
Fast, no-obligation price from our UK team for:Silicone L Profile – 3mm x 1mm – 25m Coil